Merge branch 'u1e' into merge_u1e

* u1e: (130 commits)
  invert led signals because they are active low
  duh
  allow for CS to rise before, at the same time, or after OE
  better debug pins
  watch the ethernet chip select on our debug bus
  fix timing issue on DAC outputs with rev 2.  This puts the whole system on a 90 degree phase shift
  send all gpmc signals to mictor
  updated pins to match rev2, removed dip switch, etc.  seems to compile ok.
  pins are different on rev2
  fixed makefile to compile with our new system
  add register to tell host about compatibility level and which image we are using
  move declaration to make loopback compile
  no need for protocol headers since we're not doing ethernet
  match the signal names in this design
  debug pins cleanup
  properly integrate the new tx chain
  catch up with tx_policy
  attach run_tx and run_rx to leds
  connect atr
  delay the q channel to make the channels line up on the AD9862
  ...

Conflicts:
	usrp2/control_lib/Makefile.srcs

1 files changed, 130 insertions, 0 deletions

diff --git a/usrp2/models/gpmc_model_async.v b/usrp2/models/gpmc_model_async.v
new file mode 100644
index 000000000..beeaee028
--- /dev/null
+++ b/usrp2/models/gpmc_model_async.v
@@ -0,0 +1,130 @@
+`timescale 1ps/1ps
+
+module gpmc_model_async
+  (output EM_CLK, inout [15:0] EM_D, output reg [10:1] EM_A, output reg [1:0] EM_NBE,
+   output reg EM_WAIT0, output reg EM_NCS4, output reg EM_NCS6, 
+   output reg EM_NWE, output reg EM_NOE );
+
+   assign EM_CLK = 0;
+   reg [15:0] EM_D_int;
+   assign EM_D = EM_D_int;
+   
+   initial
+     begin
+	EM_A <= 10'bz;
+	EM_NBE <= 2'b11;
+	EM_NWE <= 1;
+	EM_NOE <= 1;
+	EM_NCS4 <= 1;
+	EM_NCS6 <= 1;
+	EM_D_int <= 16'bz;
+ 	EM_WAIT0 <= 0;  // FIXME this is actually an input
+     end
+   
+   task GPMC_Write;
+      input ctrl;
+      input [10:0] addr;
+      input [15:0] data;
+      begin
+	 #23000;
+	 EM_A <= addr[10:1];
+	 EM_D_int <= data;
+	 #20100;
+	 if(ctrl)
+	   EM_NCS6 <= 0;
+	 else
+	   EM_NCS4 <= 0;
+	 #14000;
+	 EM_NWE <= 0;
+	 #77500;
+	 EM_NCS4 <= 1;
+	 EM_NCS6 <= 1;
+	 //#1.5;
+	 EM_NWE <= 1;
+	 #60000;
+	 EM_A <= 10'bz;
+	 EM_D_int <= 16'bz;
+      end
+   endtask // GPMC_Write
+
+   task GPMC_Read;
+      input ctrl;
+      input [10:0] addr;
+      begin
+	 #13000;
+	 EM_A <= addr[10:1];
+	 #3000;
+	 if(ctrl)
+	   EM_NCS6 <= 0;
+	 else
+	   EM_NCS4 <= 0;
+	 #14000;
+	 EM_NOE <= 0;
+	 #77500;
+	 EM_NCS4 <= 1;
+	 EM_NCS6 <= 1;
+	 //#1.5;
+	 $display("Data Read from GPMC: %X",EM_D);
+	 EM_NOE <= 1;
+	 #254000;
+	 EM_A <= 10'bz;
+      end
+   endtask // GPMC_Read
+   
+   initial
+     begin
+	#1000000;
+	GPMC_Write(1,36,16'hF00D);
+	#1000000;
+	GPMC_Read(1,36);
+	#1000000;
+	GPMC_Write(0,0,16'h1234);
+	GPMC_Write(0,0,16'h5678);
+	GPMC_Write(0,0,16'h9abc);
+	GPMC_Write(0,0,16'hF00D);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	#1000000;
+	GPMC_Write(0,0,16'h1234);
+	GPMC_Write(0,0,16'h5678);
+	GPMC_Write(0,0,16'h9abc);
+	GPMC_Write(0,0,16'hF00D);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'hDEAD);
+	GPMC_Write(0,0,16'h9876);
+	#1000000;
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	#1000000;
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	GPMC_Read(0,0);
+	#1000000;
+	GPMC_Read(0,0);
+	#100000000;
+	$finish;
+     end
+   
+endmodule // gpmc_model_async