Commit message (Expand) | Author | Age | Files | Lines | |
---|---|---|---|---|---|
* | Port some fixes from eval-clock to picardy | Matthias P. Braendli | 2021-06-04 | 2 | -5/+12 |
* | Implement encoder acceleration and create two UI menus | Matthias P. Braendli | 2021-05-25 | 2 | -109/+120 |
* | Fix display update after freq change | Matthias P. Braendli | 2021-05-25 | 1 | -2/+3 |
* | Change sysclk to 32MHz to avoid i2c noise at 144.320MHz | Matthias P. Braendli | 2021-05-25 | 1 | -1/+1 |
* | Setup clocks properly | Matthias P. Braendli | 2021-05-25 | 1 | -1/+3 |
* | eval-clock-cw-tx LED is CW beep | Matthias P. Braendli | 2021-05-22 | 1 | -10/+4 |
* | Add sequencing | Matthias P. Braendli | 2021-05-17 | 2 | -5/+9 |
* | Get FELDHELL to work | Matthias P. Braendli | 2021-04-15 | 8 | -57/+882 |
* | Update gitignore | Matthias P. Braendli | 2021-04-08 | 1 | -0/+9 |
* | Add some QUCS files | Matthias P. Braendli | 2021-04-08 | 14 | -0/+9974 |
* | Make cw key active low | Matthias P. Braendli | 2021-04-02 | 2 | -12/+11 |
* | Enable USB CDC ACM for eval-clock-cw-tx | Matthias P. Braendli | 2021-03-31 | 5 | -2/+140 |
* | Work on eval-clock-cw-tx sequencing | Matthias P. Braendli | 2021-03-29 | 4 | -28/+44 |
* | Create eval-clock-cw-tx sw | Matthias P. Braendli | 2021-03-20 | 17 | -0/+103724 |
* | Separate LM386 muting from switching, slow down a T/R switch a bit | Matthias P. Braendli | 2021-03-05 | 2 | -1/+14 |
* | Some updates to improve PTT clicking | Matthias P. Braendli | 2021-03-05 | 2 | -30/+43 |
* | Calibrate S meter | Matthias P. Braendli | 2021-02-17 | 2 | -10/+31 |
* | Add some schematic notes | Matthias P. Braendli | 2021-02-17 | 6 | -315/+517 |
* | Fix keyer timing | Matthias P. Braendli | 2021-01-31 | 1 | -2/+14 |
* | Add CW keyer | Matthias P. Braendli | 2021-01-31 | 5 | -84/+317 |
* | Implement CW with tone injection | Matthias P. Braendli | 2021-01-30 | 6 | -125/+222 |
* | Update README | Matthias P. Braendli | 2021-01-24 | 3 | -15/+28 |
* | Update README, notes and Qucs BPF145 | Matthias P. Braendli | 2020-12-28 | 3 | -9/+21 |
* | Add disabled CW, replace sequencer, ticks and set VFO/BFO logic | Matthias P. Braendli | 2020-12-24 | 6 | -50/+112 |
* | Switch clock timer to TIM2 | Matthias P. Braendli | 2020-12-22 | 3 | -12/+22 |
* | Simplify buttons input | Matthias P. Braendli | 2020-12-18 | 4 | -101/+28 |
* | LCD: fix setup and hold for I2C commands | Matthias P. Braendli | 2020-12-18 | 3 | -3/+42 |
* | Power decoupling and IF improvements | Matthias P. Braendli | 2020-12-15 | 8 | -562/+594 |
* | Update XTAL IF filter | Matthias P. Braendli | 2020-12-14 | 1 | -26/+26 |
* | Move to 6MHz IF | Matthias P. Braendli | 2020-12-12 | 3 | -19/+19 |
* | Add IF amp board | Matthias P. Braendli | 2020-12-08 | 6 | -3/+2193 |
* | Update README | Matthias P. Braendli | 2020-12-07 | 3 | -4/+17 |
* | Fix PTT, add AGC readout | Matthias P. Braendli | 2020-12-07 | 4 | -18/+131 |
* | Rework UI | Matthias P. Braendli | 2020-12-07 | 3 | -179/+309 |
* | Add T/R sequencer | Matthias P. Braendli | 2020-12-07 | 1 | -23/+80 |
* | Update firmware for new LO | Matthias P. Braendli | 2020-11-29 | 4 | -21/+24 |
* | Apply a few LO board corrections | Matthias P. Braendli | 2020-11-29 | 2 | -841/+857 |
* | Some changes on picardy board | Matthias P. Braendli | 2020-11-24 | 6 | -4647/+4678 |
* | Add LO board, sent to manufacturing | Matthias P. Braendli | 2020-11-24 | 8 | -1/+4450 |
* | Fix buttons and filter frequencies for LSB and USB | Matthias P. Braendli | 2020-08-28 | 4 | -847/+954 |
* | Continue TX assembly, update versions | Matthias P. Braendli | 2020-08-28 | 10 | -4736/+4887 |
* | Connect voltage switch relay | Matthias P. Braendli | 2020-07-24 | 7 | -55/+158 |
* | Configure i2c2 for display | Matthias P. Braendli | 2020-07-23 | 1 | -18/+35 |
* | Add picardy firmware project | Matthias P. Braendli | 2020-07-22 | 15 | -0/+103020 |
* | Adapt component values as assembled | Matthias P. Braendli | 2020-07-22 | 3 | -22/+25 |
* | SW: handle buttons | Matthias P. Braendli | 2020-07-17 | 5 | -127/+388 |
* | Add a few readme embellishments | Matthias P. Braendli | 2020-07-08 | 1 | -33/+34 |
* | Clarify licences | Matthias P. Braendli | 2020-07-08 | 4 | -4/+254 |
* | Prepare manufacturing filesmanufacture_20200708 | Matthias P. Braendli | 2020-07-08 | 1 | -6/+6 |
* | Explicitly connect GND and GNDA, add USB ID resistor | Matthias P. Braendli | 2020-07-08 | 3 | -9861/+9908 |