blob: c73e6ed423ce17a295f0b34dbb7081d21bab1034 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
|
/*! \page page_usrp_e1x0 USRP-E1x0 Series Device Manual
\tableofcontents
\section e1x0_features Comparative features list
- Hardware Capabilities:
- 1 transceiver card slot
- Internal PPS reference input
- Internal 10 MHz reference input
- Configurable clock rate (defaults to 64 MHz)
- Internal GPSDO option
- FPGA Capabilities:
- 2 RX DDC chains in FPGA
- 1 TX DUC chain in FPGA
- Timed commands in FPGA
- Timed sampling in FPGA
- sc8 and sc16 sample modes
- Up to 8 MHz of RF BW with 16-bit samples
- Up to 16 MHz of RF BW with 8-bit samples
\section e1x0_imgs Specify a Non-standard Image
UHD software will automatically select the USRP-Embedded FPGA image from
the installed images package. The FPGA image selection can be overridden
with the `fpga` device address parameter.
Example device address string representations to specify non-standard
FPGA image:
fpga=usrp_e100_custom.bin
\section e1x0_mcr Changing the Master Clock Rate
The master clock rate of the USRP-Embedded feeds both the FPGA DSP and
the codec chip. Hundreds of rates between 32 MHz and 64 MHz are
available. A few notable rates are:
- **64 MHz:** maximum rate of the codec chip
- **61.44 MHz:** good for UMTS/WCDMA applications
- **52 MHz:** good for GSM applications
\subsection e1x0_mcr_extvcxo Set 61.44MHz - uses external VCXO
To use the 61.44 MHz clock rate with the USRP-Embedded, two jumpers must
be moved on the device.
- **J16** is a two pin header; remove the jumper (or leave it on pin1
only).
- **J15** is a three pin header; move the jumper to (pin1, pin2).
**Note:** See instructions below to communicate the desired clock rate
to UHD software.
\subsection e1x0_intvco Set other rates - uses internal VCO
To use other clock rates, the jumpers will need to be in the default
position.
- **J16** is a two pin header; move the jumper to (pin1, pin2).
- **J15** is a three pin header; move the jumper to (pin2, pin3).
To communicate the desired clock rate into UHD software, specify the a
special device address argument, where the key is
`master_clock_rate` and the value is a rate in Hz. Example:
uhd_usrp_probe --args="master_clock_rate=52e6"
\section e1x0_clksync Clock Synchronization
\subsection e1x0_clksync_ref Ref Clock - 10MHz
The E1xx has a 10MHz TCXO which can be used to discipline the flexible
clocking by selecting `REF_INT` for the uhd::clock_config_t.
Alternately, an external 10MHz reference clock can be supplied by
soldering a connector.
- Connector **J10** (REF_IN) needs MCX connector **WM5541-ND** or
similar.
- Square wave will offer the best phase noise performance, but
sinusoid is acceptable.
- **Power level:** 0 to 15dBm
- Select `REF_SMA` in uhd::clock_config_t.
\subsection e1x0_clksync_pps PPS - Pulse Per Second
An external PPS signal for timestamp synchronization can be supplied by
soldering a connector.
- Connector **J13** (PPS) needs MCX connector **WM5541-ND** or
similar.
- Requires a square wave signal.
- **Amplitude:** 3.3 to 5 Vpp
Test the PPS input with the following app (`<args>` are device
address arguments, optional if only one USRP device is on your machine):
cd <install-path>/lib/uhd/examples
./test_pps_input --args=<args>
\subsection e1x0_clksync_gpsdo Internal GPSDO
Please see the \ref page_gpsdo for
information on configuring and using the internal GPSDO.
UHD software will always try to detect an installed GPSDO at runtime. It
is not necessary to burn a special EEPROM value for GPSDO detection.
\section e1x0_hw Hardware Setup Notes
\subsection e1x0_hw_leds Front panel LEDs
The LEDs on the front panel can be useful in debugging hardware and
software issues. The LEDs reveal the following about the state of the
device:
- **LED A:** transmitting
- **LED B:** PPS signal
- **LED C:** receiving
- **LED D:** FPGA loaded
- **LED E:** reference lock
- **LED F:** board power
\section e1x0_misc Miscellaneous
\subsection e1x0_misc_sensors Available Sensors
The following sensors are available; they can be queried through the
API.
- **ref_locked:** clock reference locked (internal/external)
- other sensors are added when the GPSDO is enabled
*/
// vim:ft=doxygen:
|
