blob: c85b78b4cf931c40faa2f3e4d3e0553b7d24569c (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
|
/*! \page page_twinrx TwinRX Daughterboard
\tableofcontents
\section twinrx_dboards TwinRX Properties
The TwinRX is a two-channel superheterodyne receiver designed for high performance spectrum monitoring and direction
finding applications. The receiver is tunable from 10 MHz - 6 GHz and has 80 MHz of instantaneous bandwidth per
channel, providing the versatility necessary to analyze a variety of signals in multiple bands of interest. Each
channel has an independent RF signal chain with preamplifiers, preselectors, and two mixer stages for superior
selectivity. Users can tune the two channels independently to simultaneously monitor uplink and downlink
communication with a combined bandwidth of 160 MHz. The ability to share the LO between channels across multiple
daughterboards enables the phase-aligned operation required to implement scalable multi-channel phased-arrays.
The receiver is capable of fast frequency hopping to detect frequency agile emitters.
\image html TwinRX_Block_Diagram.png "TwinRX Block Diagram"
\subsection twinrx_frequency_bands Frequency Bands
The receive filter banks uses switches to select between the available filters. These paths are also dependent on the
antenna switch settings. Incorrectly setting the switches generally results in attenuated input / output power. Receive
filters are band pass (series high & low pass filters).
Source code related to controlling the filter band and antenna switches resides in twinrx_experts.cpp. Specifically,
refer to the `twinrx::twinrx_freq_path_expert` class. Generally, these methods set the switches depending on the state
of the receive streams.
The following sections provide switch setting tables for antenna and filter selection for frontend's receive paths. For
further details refer to the schematics.
| Band | Range |
|--------|---------------|
| LB1 | 10 - 500 MHz |
| LB2 | 500 - 800 MHz |
| LB3 | 800 - 1.2 GHz |
| LB4 | 1.2 - 1.8 GHz |
| HB1 | 1.8 - 3.0 GHz |
| HB2 | 3.0 - 4.1 GHz |
| HB3 | 4.1 - 5.1 GHz |
| HB4 | 5.1 - 6.0 GHz |
\subsection twinrx_lo_sharing Local Oscillator Sharing
The TwinRX has the ability to export the two Local Oscillator (LO) signals from one channel to the companion channel
on the same daughterboard and/or to one or more other TwinRXs in order to form a phase-synchronous multi-channel
receiver.
| Connector | Description | Min | Nominal | Damage |
|-------------|--------------|----------|-----------|--------------|
| J1 | LO2 Export | 0 dBm | 3 dBm | NA (Output) |
| J2 | LO2 Input | 0 dBm | 2 dBm | 20 dBm |
| J3 | LO1 Export | -12 dBm | 5 dBm | NA (Output) |
| J4 | LO1 Input | -10 dBm | -5 dBm | 10 dBm |
\subsection twinrx_antenna_routing Antenna Routing
The TwinRX has two external antenna connectors (RX1 and RX2) which can be switched internally to either
receiver channel. By default RX1 is connected to the first channel and RX2 to the second.
When routing the antennas in any configuration other than the default there are some behavioral changes to be aware of.
As can be seen in the block diagram above the signal path from each antenna can be switched into a resistive divider
and then to either or both of the receive channels. If the divider is in use the incoming signal will be slightly
attenuated when compared to the direct passthrough. If both receive channels are configured to use the same antenna
the first two amplifiers and are a variable attenuator are shared. The effect of this is that the first channel's gain
settings for those amplifiers will override the second channel's. If both channels are tuned to the same frequency band
and at similar gain settings the effect will be minimal, but if the frequency or gain difference is large the resulting
gain on the second channel could be significantly lower or higher than expected. Additionally the signal path length
will increase in comparison to the direct antenna mapping so the phase of the received signal will be different
depending on the antenna mapping.
*/
// vim:ft=doxygen:
|
