1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
|
/*! \page page_transport Transport Notes
\tableofcontents
\section transport_intro Introduction
A transport is the layer between the packet interface and a device IO
interface. The advanced user can pass optional parameters into the
underlying transport layer through the device address. These optional
parameters control how the transport object allocates memory, resizes
kernel buffers, spawns threads, etc. When not spcified, the transport
layer will use values for these parameters that are known to perform
well on a variety of systems. The transport parameters are defined below
for the various transports in the UHD software:
\section transport_udp UDP Transport (Sockets)
The UDP transport is implemented with user-space sockets. This means
standard Berkeley sockets API using send()/recv().
\subsection transport_udp_params Transport parameters
The following parameters can be used to alter the transport's default
behavior (these options can be passed to a USRP device as arguments
at initialization time, see also \ref config_devaddr, or to a streamer,
see uhd::stream_args_t::args):
- `recv_frame_size:` The size of a single receive buffer in bytes
- `num_recv_frames:` The number of receive buffers to allocate
- `send_frame_size:` The size of a single send buffer in bytes
- `num_send_frames:` The number of send buffers to allocate
- `recv_buff_fullness:` The targetted fullness factor of the the buffer (typically around 90%)
<b>Notes:</b>
- `num_recv_frames` does not affect performance.
- `num_send_frames` does not affect performance.
- `recv_frame_size` and `send_frame_size` can be used
to increase or decrease the maximum number of samples per packet. The
frame sizes default to an MTU of 1472 bytes per IP/UDP packet and may be
increased if permitted by your network hardware.
\subsection transport_udp_flow Flow control parameters
The host-based flow control expects periodic update packets from the
device. These update packets inform the host of the last packet consumed
by the device, which allows the host to determine throttling conditions
for the transmission of packets. The following mechanisms affect the
transmission of periodic update packets:
- `ups_per_fifo:` The number of update packets for each FIFO's
worth of bytes sent into the device
- `ups_per_sec:` The number of update packets per second (defaults
to 20 updates per second)
\subsection transport_udp_sockbufs Resize socket buffers
It may be useful to increase the size of the socket buffers to move the
burden of buffering samples into the kernel or to buffer incoming
samples faster than they can be processed. However, if your application
cannot process samples fast enough, no amount of buffering can save you.
The following parameters can be used to alter socket's buffer sizes:
- `recv_buff_size:` The desired size of the receive buffer in
bytes
- `send_buff_size:` The desired size of the send buffer in bytes
<b>Note:</b> Large send buffers tend to decrease transmit performance.
\subsection transport_udp_latency Latency Optimization
Latency is a measurement of the time it takes a sample to travel between
the host and device. Most computer hardware and software is bandwidth
optimized, which may negatively affect latency. If your application has
strict latency requirements, please consider the following notes:
<b>Note1:</b> The time taken by the device to populate a packet is
proportional to the sample rate. Therefore, to improve receive latency,
configure the transport for a smaller frame size.
<b>Note2:</b> For overall latency improvements, look for "Interrupt
Coalescing" settings for your OS and ethernet chipset. It seems the
Intel ethernet chipsets offer fine-grained control in Linux. Also,
consult:
- <http://publib.boulder.ibm.com/infocenter/pseries/v5r3/index.jsp?topic=/com.ibm.aix.prftungd/doc/prftungd/interrupt_coal.htm>
\subsection transport_udp_linux Linux specific notes
On Linux, the maximum buffer sizes are capped by the sysctl values
`net.core.rmem_max` and `net.core.wmem_max`. To change the maximum
values, run the following commands: :
sudo sysctl -w net.core.rmem_max=<new value>
sudo sysctl -w net.core.wmem_max=<new value>
Set the values permanently by editing `/etc/sysctl.conf`.
\subsection transport_udp_windows Windows specific notes
**UDP send fast-path:** It is important to change the default UDP
behavior such that 1500 byte packets still travel through the fast path
of the sockets stack. This can be adjusted with the
FastSendDatagramThreshold registry key:
- FastSendDatagramThreshold registry key documented here:
- <http://www.microsoft.com/windows/windowsmedia/howto/articles/optimize_web.aspx#appendix_e>
- Double click and run
`<install-path>/share/uhd/FastSendDatagramThreshold.reg`
- A system reboot is recommended after the registry key change.
<b>Power profile:</b> The Windows power profile can seriously impact
instantaneous bandwidth. Application can take time to ramp-up to full
performance capability. It is recommended that users set the power
profile to "high performance".
\section transport_usb USB Transport (LibUSB)
The USB transport is implemented with LibUSB. LibUSB provides an
asynchronous API for USB bulk transfers.
\subsection transport_usb_params Transport parameters
The following parameters can be used to alter the transport's default
behavior:
- `recv_frame_size:` The size of a single receive transfers in
bytes
- `num_recv_frames:` The number of simultaneous receive transfers
- `send_frame_size:` The size of a single send transfers in bytes
- `num_send_frames:` The number of simultaneous send transfers
\subsection transport_usb_udev Setup Udev for USB (Linux)
On Linux, Udev handles USB plug and unplug events. The following
commands install a Udev rule so that non-root users may access the
device:
cd <install-path>/lib/uhd/utils
sudo cp uhd-usrp.rules /etc/udev/rules.d/
sudo udevadm control --reload-rules
sudo udevadm trigger
\subsection transport_usb_installwin Install USB driver (Windows)
A driver package must be installed to use a USB-based product with UHD
software:
- Download the driver from the UHD wiki page
<a href="http://files.ettus.com/binaries/misc/erllc_uhd_winusb_driver.zip">here</a>.
- Unzip the file into a known location. We will refer to this as the `<directory>`.
- Open the device manager and plug in the USRP device. You will see an
unrecognized USB device in the device manager.
- Right click on the unrecognized USB device and select update/install
driver software (may vary for your OS).
- In the driver installation wizard, select "browse for driver",
browse to the `<directory>`, and select the `.inf` file.
- Continue through the installation wizard until the driver is
installed.
*/
// vim:ft=doxygen:
|
