1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
========================================================================
UHD - General Application Notes
========================================================================
.. contents:: Table of Contents
------------------------------------------------------------------------
Tuning notes
------------------------------------------------------------------------
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Two-stage tuning process
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
A USRP device has two stages of tuning:
* RF front-end: translates bewteen RF and IF
* DSP: translates between IF and baseband
In a typical use-case, the user specifies an overall center frequency for the signal chain.
The RF front-end will be tuned as close as possible to the center frequency,
and the DSP will account for the error in tuning between target frequency and actual frequency.
The user may also explicitly control both stages of tuning through the tune_request_t object.
Pseudo-code for tuning the receive chain:
::
//tuning to a desired center frequency
usrp->set_rx_freq(my_frequency_in_hz);
--OR--
//advanced tuning with tune_request_t
uhd::tune_request_t tune_req;
tune_req.target_freq = my_frequency_in_hz;
//fill in tune request fields...
usrp->set_rx_freq(tune_req);
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
RF front-end settling time
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
After tuning, the RF front-end will need time to settle into a usable state.
Typically, this means that the local oscillators must be given time to lock before streaming begins.
Lock time is not consistent; it varies depending upon the device and requested settings.
After tuning and before streaming, the user should
wait for the "lo_locked" sensor to become true,
or sleep for a conservative amount of time (perhaps a second).
Pseudo-code for dealing with settling time after tuning on receive:
::
usrp->set_rx_freq(...);
sleep(1);
usrp->issue_stream_command(...);
--OR--
usrp->set_rx_freq(...);
while (not usrp->get_rx_sensor("lo_locked").to_bool()){
//sleep for a short time in milliseconds
}
usrp->issue_stream_command(...);
------------------------------------------------------------------------
Threading notes
------------------------------------------------------------------------
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Thread safety notes
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
For the most part, UHD is thread-safe.
Please observe the following limitations:
**Fast-path thread requirements:**
It is safe to call send() and recv() simultaneously. However,
it is not safe to call recv() simultaneously from different thread contexts.
The same rule applies for recv(), send(), and recv_async_msg().
One thread context per fast-path device method at a time.
**Slow-path thread requirements:**
It is safe to change multiple settings simultaneously. However,
this could leave the settings for a device in an uncertain state.
The is because changing one setting could have an impact on how a call affects other settings.
Example: setting the channel mapping affects how the antennas are set.
It is recommended to use at most one thread context for manipulating device settings.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Thread priority scheduling
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
When the UHD spawns a new thread it may try to boost the thread's scheduling priority.
When setting the priority fails, the UHD prints out an error.
This error is harmless, it simply means that the thread will have a normal scheduling priority.
**Linux Notes:**
Non-privileged users need special permission to change the scheduling priority.
Add the following line to */etc/security/limits.conf*:
::
@<my_group> - rtprio 99
Replace <my_group> with a group to which your user belongs.
Settings will not take effect until the user has logged in and out.
------------------------------------------------------------------------
Misc notes
------------------------------------------------------------------------
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Support for dynamically loadable modules
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
For a module to be loaded at runtime, it must be:
* found in the UHD_MODULE_PATH environment variable,
* installed into the <install-path>/share/uhd/modules directory,
* or installed into /usr/share/uhd/modules directory (unix only).
|
