1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
|
// radio top level module
// Contains all clock-rate DSP components, all radio and hardware controls and settings
// Communication with outside world is exclusively via a single in/out axi cvita port
// Paths are separated by the lower 2 bits of stream ID, as follows:
//
// SID[1:0] IN OUT
// 0 Transmit Data (DATA) Transmit Flow Control, ACK/Error (CTXT)
// 1 Control (SPI, settings) (CTXT) Response (readback) (CTXT)
// 2 Receive Flow Control (CTXT) Receive Data (DATA)
// 3 Receive Commands (CTXT) Receive Command ACK/ERROR (CTXT)
module radio
#(
parameter CHIPSCOPE = 0,
parameter DELETE_DSP = 0
)
(input radio_clk, input radio_rst,
input [31:0] rx, output [31:0] tx,
inout [31:0] db_gpio,
inout [31:0] fp_gpio,
output [7:0] sen, output sclk, output mosi, input miso,
output [7:0] misc_outs, output [2:0] leds,
input bus_clk, input bus_rst,
input [63:0] in_tdata, input in_tlast, input in_tvalid, output in_tready,
output [63:0] out_tdata, output out_tlast, output out_tvalid, input out_tready,
input [63:0] tx_tdata_bi, input tx_tlast_bi, input tx_tvalid_bi, output tx_tready_bi,
output [63:0] tx_tdata_bo, output tx_tlast_bo, output tx_tvalid_bo, input tx_tready_bo,
input pps,
output sync_dacs,
output [31:0] debug
);
// ///////////////////////////////////////////////////////////////////////////////
// FIFO Interfacing to the bus clk domain
// in_tdata splits to tx_tdata and ctrl_tdata
// rx_tdata and resp_tdata get muxed to out_tdata
// Everything except rx flow control must cross in to radio_clk domain before further use
// _b signifies bus_clk domain, _r signifies radio_clk domain, _b_fc is bus_clk domain, post flow control
wire [63:0] ctrl_tdata_b, ctrl_tdata_r;
wire ctrl_tready_b, ctrl_tready_r, ctrl_tvalid_b, ctrl_tvalid_r;
wire ctrl_tlast_b, ctrl_tlast_r;
wire [63:0] ctrl_tdata_s_r;
wire ctrl_tready_s_r, ctrl_tvalid_s_r;
wire ctrl_tlast_s_r;
wire [63:0] resp_tdata_b, resp_tdata_r;
wire resp_tready_b, resp_tready_r, resp_tvalid_b, resp_tvalid_r;
wire resp_tlast_b, resp_tlast_r;
wire [63:0] rx_tdata_b, rx_tdata_b_fc, rx_tdata_r;
wire rx_tready_b, rx_tready_b_fc, rx_tready_r, rx_tvalid_b, rx_tvalid_b_fc, rx_tvalid_r;
wire rx_tlast_b, rx_tlast_b_fc, rx_tlast_r;
// IJB. _b signals now unused since adding DRAM FIFO.
wire [63:0] tx_tdata_b, tx_tdata_r;
wire tx_tready_b, tx_tready_r, tx_tvalid_b, tx_tvalid_r;
wire tx_tlast_b, tx_tlast_r;
wire [63:0] txresp_tdata_b, txresp_tdata_r;
wire txresp_tready_b, txresp_tready_r, txresp_tvalid_b, txresp_tvalid_r;
wire txresp_tlast_b, txresp_tlast_r;
wire [63:0] rxfc_tdata_b;
wire rxfc_tready_b, rxfc_tvalid_b, rxfc_tlast_b;
wire [63:0] rx_mux_tdata_r;
wire rx_mux_tready_r, rx_mux_tvalid_r;
wire rx_mux_tlast_r;
wire [63:0] rx_err_tdata_r;
wire rx_err_tready_r, rx_err_tvalid_r;
wire rx_err_tlast_r;
//IJB debug
wire [63:0] tx_tdata_bo_debug;
wire tx_tlast_bo_debug, tx_tvalid_bo_debug, tx_tready_bo_debug;
axi_mux4 #(.PRIO(0), .WIDTH(64), .BUFFER(1)) radio_mux
(.clk(bus_clk), .reset(bus_rst), .clear(1'b0),
.i0_tdata(txresp_tdata_b), .i0_tlast(txresp_tlast_b), .i0_tvalid(txresp_tvalid_b), .i0_tready(txresp_tready_b), // TX Flow Control/ACK
.i1_tdata(resp_tdata_b), .i1_tlast(resp_tlast_b), .i1_tvalid(resp_tvalid_b), .i1_tready(resp_tready_b), // Control Response
.i2_tdata(rx_tdata_b_fc), .i2_tlast(rx_tlast_b_fc), .i2_tvalid(rx_tvalid_b_fc), .i2_tready(rx_tready_b_fc), // RX Data
.i3_tdata(), .i3_tlast(), .i3_tvalid(1'b0), .i3_tready(), // RX Command ACK/ERR
.o_tdata(out_tdata), .o_tlast(out_tlast), .o_tvalid(out_tvalid), .o_tready(out_tready));
wire [63:0] vheader;
wire [1:0] vdest = vheader[1:0]; // Switch by bottom 2 bits of SID
axi_demux4 #(.ACTIVE_CHAN(4'b0111), .WIDTH(64)) radio_demux
(.clk(bus_clk), .reset(bus_rst), .clear(1'b0),
.header(vheader), .dest(vdest),
.i_tdata(in_tdata), .i_tlast(in_tlast), .i_tvalid(in_tvalid), .i_tready(in_tready),
.o0_tdata(tx_tdata_bo), .o0_tlast(tx_tlast_bo), .o0_tvalid(tx_tvalid_bo), .o0_tready(tx_tready_bo), // TX Data
.o1_tdata(ctrl_tdata_b), .o1_tlast(ctrl_tlast_b), .o1_tvalid(ctrl_tvalid_b), .o1_tready(ctrl_tready_b), // Control
.o2_tdata(rxfc_tdata_b), .o2_tlast(rxfc_tlast_b), .o2_tvalid(rxfc_tvalid_b), .o2_tready(rxfc_tready_b), // RX Flow Control
.o3_tdata(), .o3_tlast(), .o3_tvalid(), .o3_tready(1'b1)); // RX Command
axi_fifo_2clk #(.WIDTH(65), .SIZE(9)) ctrl_fifo
(.reset(bus_rst),
.i_aclk(bus_clk), .i_tvalid(ctrl_tvalid_b), .i_tready(ctrl_tready_b), .i_tdata({ctrl_tlast_b,ctrl_tdata_b}),
.o_aclk(radio_clk), .o_tvalid(ctrl_tvalid_s_r), .o_tready(ctrl_tready_s_r), .o_tdata({ctrl_tlast_s_r,ctrl_tdata_s_r}));
// For timing closure ..paths lead back from 64bit time comparison.
axi_fifo_short #(.WIDTH(65)) ctrl_fifo_s
(
.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.i_tdata({ctrl_tlast_s_r,ctrl_tdata_s_r}), .i_tvalid(ctrl_tvalid_s_r), .i_tready(ctrl_tready_s_r),
.o_tdata({ctrl_tlast_r,ctrl_tdata_r}), .o_tvalid(ctrl_tvalid_r), .o_tready(ctrl_tready_r),
.space(), .occupied()
);
axi_fifo_2clk #(.WIDTH(65), .SIZE(13)) tx_fifo
(.reset(bus_rst),
.i_aclk(bus_clk), .i_tvalid(tx_tvalid_bi), .i_tready(tx_tready_bi), .i_tdata({tx_tlast_bi,tx_tdata_bi}),
.o_aclk(radio_clk), .o_tvalid(tx_tvalid_r), .o_tready(tx_tready_r), .o_tdata({tx_tlast_r,tx_tdata_r}));
axi_fifo_2clk #(.WIDTH(65), .SIZE(9)) resp_fifo
(.reset(radio_rst),
.i_aclk(radio_clk), .i_tvalid(resp_tvalid_r), .i_tready(resp_tready_r), .i_tdata({resp_tlast_r,resp_tdata_r}),
.o_aclk(bus_clk), .o_tvalid(resp_tvalid_b), .o_tready(resp_tready_b), .o_tdata({resp_tlast_b,resp_tdata_b}));
axi_fifo_2clk #(.WIDTH(65), .SIZE(10)) rx_fifo
(.reset(radio_rst),
.i_aclk(radio_clk), .i_tvalid(rx_mux_tvalid_r), .i_tready(rx_mux_tready_r), .i_tdata({rx_mux_tlast_r,rx_mux_tdata_r}),
.o_aclk(bus_clk), .o_tvalid(rx_tvalid_b), .o_tready(rx_tready_b), .o_tdata({rx_tlast_b,rx_tdata_b}));
axi_fifo_2clk #(.WIDTH(65), .SIZE(9)) txresp_fifo
(.reset(radio_rst),
.i_aclk(radio_clk), .i_tvalid(txresp_tvalid_r), .i_tready(txresp_tready_r), .i_tdata({txresp_tlast_r,txresp_tdata_r}),
.o_aclk(bus_clk), .o_tvalid(txresp_tvalid_b), .o_tready(txresp_tready_b), .o_tdata({txresp_tlast_b,txresp_tdata_b}));
// /////////////////////////////////////////////////////////////////////////////////////
// Setting bus and controls
localparam SR_DACSYNC = 8'd5;
localparam SR_LOOPBACK = 8'd6;
localparam SR_TEST = 8'd7;
localparam SR_SPI = 8'd8;
localparam SR_GPIO = 8'd16;
localparam SR_MISC_OUTS = 8'd24;
localparam SR_READBACK = 8'd32;
localparam SR_TX_CTRL = 8'd64;
localparam SR_RX_CTRL = 8'd96;
localparam SR_TIME = 8'd128;
localparam SR_RX_DSP = 8'd144;
localparam SR_TX_DSP = 8'd184;
localparam SR_LEDS = 8'd196;
localparam SR_FP_GPIO = 8'd200;
localparam SR_RX_FRONT = 8'd208;
localparam SR_TX_FRONT = 8'd216;
wire set_stb;
wire [7:0] set_addr;
wire [31:0] set_data;
wire set_stb_b;
wire [7:0] set_addr_b;
wire [31:0] set_data_b;
wire [31:0] fp_gpio_readback, gpio_readback, spi_readback;
wire run_rx, run_tx;
wire strobe_tx;
wire spi_ready;
reg [63:0] rb_data;
wire [2:0] rb_addr;
wire [63:0] vita_time, vita_time_lastpps;
wire [31:0] test_readback;
wire loopback;
radio_ctrl_proc radio_ctrl_proc
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.ctrl_tdata(ctrl_tdata_r), .ctrl_tlast(ctrl_tlast_r), .ctrl_tvalid(ctrl_tvalid_r), .ctrl_tready(ctrl_tready_r),
.resp_tdata(resp_tdata_r), .resp_tlast(resp_tlast_r), .resp_tvalid(resp_tvalid_r), .resp_tready(resp_tready_r),
.vita_time(vita_time),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.ready(spi_ready), .readback(rb_data),
.debug());
// Radio Readback Mux
always @*
case(rb_addr)
3'd0 : rb_data <= { spi_readback, gpio_readback};
3'd1 : rb_data <= vita_time;
3'd2 : rb_data <= vita_time_lastpps;
3'd3 : rb_data <= {rx, test_readback};
3'd4 : rb_data <= {32'b0, fp_gpio_readback};
default : rb_data <= 64'd0;
endcase // case (rb_addr)
settings_bus_crossclock
#(.FLOW_CTRL(0))
settings_bus_crossclock
(.clk_i(radio_clk), .rst_i(radio_rst),
.set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
.clk_o(bus_clk), .rst_o(bus_rst),
.set_stb_o(set_stb_b), .set_addr_o(set_addr_b), .set_data_o(set_data_b),
.blocked(1'b0));
// Write this register with any value to create DAC sync operation
setting_reg #(.my_addr(SR_DACSYNC), .awidth(8), .width(1)) sr_dacsync
(.clk(radio_clk), .rst(radio_rst), .strobe(set_stb), .addr(set_addr), .in(set_data),
.out(), .changed(sync_dacs));
// Set this register to loop TX data directly to RX data.
setting_reg #(.my_addr(SR_LOOPBACK), .awidth(8), .width(1)) sr_loopback
(.clk(radio_clk), .rst(radio_rst), .strobe(set_stb), .addr(set_addr), .in(set_data),
.out(loopback), .changed());
// Set this register to put a test value on the readback mux.
setting_reg #(.my_addr(SR_TEST), .awidth(8), .width(32)) sr_test
(.clk(radio_clk), .rst(radio_rst), .strobe(set_stb), .addr(set_addr), .in(set_data),
.out(test_readback), .changed());
setting_reg #(.my_addr(SR_READBACK), .awidth(8), .width(3)) sr_rdback
(.clk(radio_clk), .rst(radio_rst), .strobe(set_stb), .addr(set_addr), .in(set_data),
.out(rb_addr), .changed());
setting_reg #(.my_addr(SR_MISC_OUTS), .awidth(8), .width(8), .at_reset(8'h0)) sr_misc
(.clk(radio_clk), .rst(radio_rst), .strobe(set_stb), .addr(set_addr), .in(set_data),
.out(misc_outs), .changed());
simple_spi_core #(.BASE(SR_SPI), .WIDTH(8), .CLK_IDLE(0), .SEN_IDLE(8'hFF)) radio_spi
(.clock(radio_clk), .reset(radio_rst),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.readback(spi_readback), .ready(spi_ready),
.sen(sen), .sclk(sclk), .mosi(mosi), .miso(miso),
.debug());
gpio_atr #(.BASE(SR_GPIO), .WIDTH(32)) gpio_atr
(.clk(radio_clk),.reset(radio_rst),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.rx(run_rx), .tx(run_tx),
.gpio(db_gpio), .gpio_readback(gpio_readback) );
gpio_atr #(.BASE(SR_FP_GPIO), .WIDTH(32)) fp_gpio_atr
(.clk(radio_clk),.reset(radio_rst),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.rx(run_rx), .tx(run_tx),
.gpio(fp_gpio), .gpio_readback(fp_gpio_readback) );
gpio_atr #(.BASE(SR_LEDS), .WIDTH(3), .default_ddr(3'b111), .default_idle(3'b000)) gpio_leds
(.clk(radio_clk),.reset(radio_rst),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.rx(run_rx), .tx(run_tx),
.gpio(leds), .gpio_readback() );
timekeeper #(.BASE(SR_TIME)) timekeeper
(.clk(radio_clk), .reset(radio_rst), .pps(pps),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.vita_time(vita_time), .vita_time_lastpps(vita_time_lastpps));
// /////////////////////////////////////////////////////////////////////////////////
// TX Chain
wire [175:0] txsample_tdata;
wire txsample_tvalid, txsample_tready;
wire [31:0] sample_tx;
wire ack_or_error, packet_consumed;
wire [11:0] seqnum;
wire [63:0] error_code;
wire [31:0] sid;
wire [23:0] tx_fe_i, tx_fe_q;
new_tx_deframer tx_deframer
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.i_tdata(tx_tdata_r), .i_tlast(tx_tlast_r), .i_tvalid(tx_tvalid_r), .i_tready(tx_tready_r),
.sample_tdata(txsample_tdata), .sample_tvalid(txsample_tvalid), .sample_tready(txsample_tready));
new_tx_control #(.BASE(SR_TX_CTRL)) tx_control
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.vita_time(vita_time),
.ack_or_error(ack_or_error), .packet_consumed(packet_consumed),
.seqnum(seqnum), .error_code(error_code), .sid(sid),
.sample_tdata(txsample_tdata), .sample_tvalid(txsample_tvalid), .sample_tready(txsample_tready),
.sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
.debug());
tx_responder #(.BASE(SR_TX_CTRL+2)) tx_responder
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.ack_or_error(ack_or_error), .packet_consumed(packet_consumed),
.seqnum(seqnum), .error_code(error_code), .sid(sid),
.vita_time(vita_time),
.o_tdata(txresp_tdata_r), .o_tlast(txresp_tlast_r), .o_tvalid(txresp_tvalid_r), .o_tready(txresp_tready_r));
generate
if (DELETE_DSP==0) begin: tx_dsp
duc_chain #(.BASE(SR_TX_DSP), .DSPNO(0), .WIDTH(24)) duc_chain
(.clk(radio_clk), .rst(radio_rst), .clr(1'b0),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.tx_fe_i(tx_fe_i),.tx_fe_q(tx_fe_q),
.sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
.debug() );
tx_frontend #(.BASE(SR_TX_FRONT), .WIDTH_OUT(16), .IQCOMP_EN(1)) tx_frontend
(.clk(radio_clk), .rst(radio_rst),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.tx_i(tx_fe_i), .tx_q(tx_fe_q), .run(run_tx),
.dac_a(tx[31:16]), .dac_b(tx[15:0]));
end
endgenerate
// /////////////////////////////////////////////////////////////////////////////////
// RX Chain
wire full, eob_rx;
wire strobe_rx;
wire [31:0] sample_rx;
wire [31:0] rx_sid;
wire [11:0] rx_seqnum;
source_flow_control #(.BASE(SR_RX_CTRL+6)) rx_sfc
(.clk(bus_clk), .reset(bus_rst), .clear(1'b0),
.set_stb(set_stb_b), .set_addr(set_addr_b), .set_data(set_data_b),
.fc_tdata(rxfc_tdata_b), .fc_tlast(rxfc_tlast_b), .fc_tvalid(rxfc_tvalid_b), .fc_tready(rxfc_tready_b),
.in_tdata(rx_tdata_b), .in_tlast(rx_tlast_b), .in_tvalid(rx_tvalid_b), .in_tready(rx_tready_b),
.out_tdata(rx_tdata_b_fc), .out_tlast(rx_tlast_b_fc), .out_tvalid(rx_tvalid_b_fc), .out_tready(rx_tready_b_fc) );
new_rx_framer #(.BASE(SR_RX_CTRL+4),.CHIPSCOPE(CHIPSCOPE)) new_rx_framer
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.vita_time(vita_time),
.strobe(strobe_rx), .sample(sample_rx), .run(run_rx), .eob(eob_rx), .full(full),
.sid(rx_sid), .seqnum(rx_seqnum),
.o_tdata(rx_tdata_r), .o_tlast(rx_tlast_r), .o_tvalid(rx_tvalid_r), .o_tready(rx_tready_r),
.debug());
new_rx_control #(.BASE(SR_RX_CTRL)) new_rx_control
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
.vita_time(vita_time),
.strobe(strobe_rx), .run(run_rx), .eob(eob_rx), .full(full),
.sid(rx_sid), .seqnum(rx_seqnum),
.err_tdata(rx_err_tdata_r), .err_tlast(rx_err_tlast_r), .err_tvalid(rx_err_tvalid_r), .err_tready(rx_err_tready_r),
.debug());
wire [23:0] rx_corr_i, rx_corr_q;
// Digital Loopback TX -> RX (Pipeline immediately inside rx_frontend).
wire [31:0] rx_fe = loopback ? tx : rx;
generate
if (DELETE_DSP==0)
begin: rx_dsp
rx_frontend #(.BASE(SR_RX_FRONT)) rx_frontend
(.clk(radio_clk),.rst(radio_rst),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.adc_a(rx_fe[31:16]),.adc_ovf_a(1'b0),
.adc_b(rx_fe[15:0]),.adc_ovf_b(1'b0),
.i_out(rx_corr_i), .q_out(rx_corr_q),
.run(run_rx0_d1 | run_rx1_d1), .debug());
ddc_chain_x300 #(.BASE(SR_RX_DSP), .DSPNO(0), .WIDTH(24)) ddc_chain
(.clk(radio_clk), .rst(radio_rst), .clr(1'b0),
.set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
.rx_fe_i(rx_corr_i),.rx_fe_q(rx_corr_q),
.sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
.debug() );
end
endgenerate
// /////////////////////////////////////////////////////////////////////////////////
// RX Channel Muxing
axi_mux4 #(.PRIO(1), .WIDTH(64)) rx_mux
(.clk(radio_clk), .reset(radio_rst), .clear(1'b0),
.i0_tdata(rx_tdata_r), .i0_tlast(rx_tlast_r), .i0_tvalid(rx_tvalid_r), .i0_tready(rx_tready_r),
.i1_tdata(rx_err_tdata_r), .i1_tlast(rx_err_tlast_r), .i1_tvalid(rx_err_tvalid_r), .i1_tready(rx_err_tready_r),
.i2_tdata(), .i2_tlast(), .i2_tvalid(1'b0), .i2_tready(),
.i3_tdata(), .i3_tlast(), .i3_tvalid(1'b0), .i3_tready(),
.o_tdata(rx_mux_tdata_r), .o_tlast(rx_mux_tlast_r), .o_tvalid(rx_mux_tvalid_r), .o_tready(rx_mux_tready_r));
// /////////////////////////////////////////////////////////////////////////////////
// Debug
/* -----\/----- EXCLUDED -----\/-----
generate
if (CHIPSCOPE) begin: chipscope_gen
(* keep = "true", max_fanout = 10 *) reg debug_set_stb;
(* keep = "true", max_fanout = 10 *) reg [7:0] debug_set_addr;
(* keep = "true", max_fanout = 10 *) reg [31:0] debug_set_data;
(* keep = "true", max_fanout = 10 *) reg [63:0] debug_ctrl_tdata_r;
(* keep = "true", max_fanout = 10 *) reg debug_ctrl_tlast_r;
(* keep = "true", max_fanout = 10 *) reg debug_ctrl_tvalid_r;
(* keep = "true", max_fanout = 10 *) reg debug_ctrl_tready_r;
always @(posedge radio_clk) begin
debug_set_stb <= set_stb;
debug_set_addr <= set_addr[7:0];
debug_set_data <= set_data[31:0];
debug_ctrl_tdata_r <= ctrl_tdata_r;
debug_ctrl_tlast_r <= ctrl_tlast_r;
debug_ctrl_tvalid_r <= ctrl_tvalid_r;
debug_ctrl_tready_r <= ctrl_tready_r;
end
wire [35:0] CONTROL0;
wire [63:0] TRIG0;
assign TRIG0 = {
sync_dacs, // 109
loopback, // 108
debug_ctrl_tready_r, // 107
debug_ctrl_tvalid_r, // 106
debug_ctrl_tlast_r, // 105
debug_ctrl_tdata_r, // 104:41
debug_set_stb, // 40
debug_set_addr, // 39:32
debug_set_data // 31:0
};
chipscope_ila chipscope_ila_i0
(
.CONTROL(CONTROL0), // INOUT BUS [35:0]
.CLK(radio_clk), // IN
.TRIG0(TRIG0 ) // IN BUS [255:0]
);
chipscope_icon chipscope_icon_i0
(
.CONTROL0(CONTROL0) // INOUT BUS [35:0]
);
end // block: chipscope
endgenerate
-----/\----- EXCLUDED -----/\----- */
/* -----\/----- EXCLUDED -----\/-----
generate
if (CHIPSCOPE) begin: chipscope_gen
(* keep = "true", max_fanout = 10 *) reg [5:0] debug_error_code; // 174:169
(* keep = "true", max_fanout = 10 *) reg debug_ack_or_error; // 168
(* keep = "true", max_fanout = 10 *) reg debug_run_rx; // 167
(* keep = "true", max_fanout = 10 *) reg debug_strobe_rx; // 166
(* keep = "true", max_fanout = 10 *) reg debug_rx_err_tvalid_r; // 165
(* keep = "true", max_fanout = 10 *) reg debug_rx_err_tready_r; // 164
(* keep = "true", max_fanout = 10 *) reg debug_rx_err_tlast_r; // 163
(* keep = "true", max_fanout = 10 *) reg debug_rx_tvalid_r; // 162
(* keep = "true", max_fanout = 10 *) reg debug_rx_tready_r; // 161
(* keep = "true", max_fanout = 10 *) reg debug_rx_tlast_r; // 160
(* keep = "true", max_fanout = 10 *) reg [31:0] debug_sample_rx; // 159:128
(* keep = "true", max_fanout = 10 *) reg [63:0] debug_rx_err_tdata_r; // 127:64
(* keep = "true", max_fanout = 10 *) reg [63:0] debug_rx_tdata_r; // 63:0
(* keep = "true", max_fanout = 10 *) reg debug_set_stb;
(* keep = "true", max_fanout = 10 *) reg [7:0] debug_set_addr;
(* keep = "true", max_fanout = 10 *) reg [7:0] debug_set_data;
(* keep = "true", max_fanout = 10 *) reg [63:0] debug_tx_tdata_r;
(* keep = "true", max_fanout = 10 *) reg debug_tx_tlast_r;
(* keep = "true", max_fanout = 10 *) reg debug_tx_tvalid_r;
(* keep = "true", max_fanout = 10 *) reg debug_tx_tready_r;
(* keep = "true", max_fanout = 10 *) reg [11:0] debug_seq_id;
(* keep = "true", max_fanout = 10 *) reg debug_run_tx;
(* keep = "true", max_fanout = 10 *) reg debug_strobe_tx;
always @(posedge radio_clk) begin
debug_set_stb <= set_stb;
debug_set_addr <= set_addr;
debug_set_data <= set_data[7:0];
debug_error_code <= error_code[37:32];
debug_ack_or_error <= ack_or_error;
debug_run_rx <= run_rx ;
debug_strobe_rx <= strobe_rx;
debug_rx_err_tvalid_r <= rx_err_tvalid_r;
debug_rx_err_tready_r <= rx_err_tready_r;
debug_rx_err_tlast_r <= rx_err_tlast_r;
debug_rx_tvalid_r <= rx_tvalid_r ;
debug_rx_tready_r <= rx_tready_r;
debug_rx_tlast_r <= rx_tlast_r;
debug_sample_rx[31:0] <= sample_rx[31:0];
debug_rx_err_tdata_r[63:0] <= rx_err_tdata_r[63:0];
debug_rx_tdata_r[63:0] <= rx_tdata_r[63:0];
debug_tx_tdata_r <= tx_tdata_r;
debug_tx_tlast_r <= tx_tlast_r;
debug_tx_tvalid_r <= tx_tvalid_r;
debug_tx_tready_r <= tx_tready_r;
debug_seq_id <= error_code[11:0];
debug_ack_or_error <= ack_or_error;
debug_run_tx <= run_tx;
debug_strobe_tx <= strobe_tx;
end // always @ (posedge radio_clk)
wire [35:0] CONTROL0;
wire [255:0] TRIG0;
assign TRIG0 = {
debug_strobe_tx, // 87
debug_run_tx, // 86
debug_ack_or_error, // 85
debug_error_code[5:0], // 84:79
debug_seq_id[11:0], // 78:67
debug_tx_tready_r, // 66
debug_tx_tvalid_r, // 65
debug_tx_tlast_r, // 64
debug_tx_tdata_r[63:0] // 63:0
};
chipscope_ila chipscope_ila_i0
(
.CONTROL(CONTROL0), // INOUT BUS [35:0]
.CLK(radio_clk), // IN
.TRIG0(TRIG0 ) // IN BUS [255:0]
);
chipscope_icon chipscope_icon_i0
(
.CONTROL0(CONTROL0) // INOUT BUS [35:0]
);
end // block: chipscope
endgenerate
-----/\----- EXCLUDED -----/\----- */
endmodule // radio
|
