path: root/fpga/usrp3/top/x300/bus_int.v

//
// Copyright 2013 Ettus Research LLC
//

`define LOG2(N) (\
                 N < 2 ? 0 : \
                 N < 4 ? 1 : \
                 N < 8 ? 2 : \
                 N < 16 ? 3 : \
                 N < 32 ? 4 : \
                 N < 64 ? 5 : \
		 N < 128 ? 6 : \
		 N < 256 ? 7 : \
		 N < 512 ? 8 : \
		 N < 1024 ? 9 : \
                 10)

module bus_int
  #(
    parameter  dw  = 32,  // Data bus width
    parameter  aw  = 16,  // Address bus width, for byte addressibility, 16 = 64K byte memory space
    parameter  sw  = 4   // Select width -- 32-bit data bus with 8-bit granularity.
    )
   (input clk, input reset,
    output sen, output sclk, output mosi, input miso,
    inout scl0, inout sda0,
    inout scl1, inout sda1,
    inout scl2, inout sda2,
    output gps_txd, input gps_rxd,
    output debug_txd, input debug_rxd,
    output [7:0] leds,
    output [3:0] sw_rst,
    // SFP+ 0
    input SFPP0_ModAbs,
    input SFPP0_TxFault, // Current 10G PMA/PCS apparently ignores this signal.
    input SFPP0_RxLOS,
    inout SFPP0_RS0,
    inout SFPP0_RS1,
    // SFP+ 1
    input SFPP1_ModAbs,
    input SFPP1_TxFault, // Current 10G PMA/PCS apparently ignores this signal.
    input SFPP1_RxLOS,
    inout SFPP1_RS0,
    inout SFPP1_RS1,
    //
    input [4:0] clock_status,
    output [6:0] clock_control,
    // ETH0
    output [63:0] eth0_tx_tdata, output [3:0] eth0_tx_tuser, output eth0_tx_tlast, output eth0_tx_tvalid, input eth0_tx_tready,
    input [63:0] eth0_rx_tdata, input [3:0] eth0_rx_tuser, input eth0_rx_tlast, input eth0_rx_tvalid, output eth0_rx_tready,
    // ETH1
    output [63:0] eth1_tx_tdata, output [3:0] eth1_tx_tuser, output eth1_tx_tlast, output eth1_tx_tvalid, input eth1_tx_tready,
    input [63:0] eth1_rx_tdata, input [3:0] eth1_rx_tuser, input eth1_rx_tlast, input eth1_rx_tvalid, output eth1_rx_tready,
    // Radio0
    output [63:0] r0o_tdata, output r0o_tlast, output r0o_tvalid, input r0o_tready,
    input [63:0] r0i_tdata, input r0i_tlast, input r0i_tvalid, output r0i_tready,
    // Radio1
    output [63:0] r1o_tdata, output r1o_tlast, output r1o_tvalid, input r1o_tready,
    input [63:0] r1i_tdata, input r1i_tlast, input r1i_tvalid, output r1i_tready,
    // CE0
    output [63:0] ce0o_tdata, output ce0o_tlast, output ce0o_tvalid, input ce0o_tready,
    input [63:0] ce0i_tdata, input ce0i_tlast, input ce0i_tvalid, output ce0i_tready,
    // CE1
    output [63:0] ce1o_tdata, output ce1o_tlast, output ce1o_tvalid, input ce1o_tready,
    input [63:0] ce1i_tdata, input ce1i_tlast, input ce1i_tvalid, output ce1i_tready,
    // CE2
    output [63:0] ce2o_tdata, output ce2o_tlast, output ce2o_tvalid, input ce2o_tready,
    input [63:0] ce2i_tdata, input ce2i_tlast, input ce2i_tvalid, output ce2i_tready,
    //iop2 message fifos
    output [63:0] o_iop2_msg_tdata, output o_iop2_msg_tvalid, output o_iop2_msg_tlast, input o_iop2_msg_tready,
    input [63:0] i_iop2_msg_tdata, input i_iop2_msg_tvalid, input i_iop2_msg_tlast, output i_iop2_msg_tready,
    // PCIe
    output [63:0] pcio_tdata, output pcio_tlast, output pcio_tvalid, input pcio_tready,
    input [63:0] pcii_tdata, input pcii_tlast, input pcii_tvalid, output pcii_tready,
    //------------------------------------------------------------------
    // Wishbone Slave Interface(s)
    //------------------------------------------------------------------
    input [dw-1:0] s4_dat_i,
    output [dw-1:0] s4_dat_o,
    output [aw-1:0] s4_adr,
    output [sw-1:0] s4_sel,
    input s4_ack,
    output s4_stb,
    output s4_cyc,
    output s4_we,
    input s4_int,  // IJB. Nothing to connect this too!! No IRQ controller on x300.

    input [dw-1:0] s5_dat_i,
    output [dw-1:0] s5_dat_o,
    output [aw-1:0] s5_adr,
    output [sw-1:0] s5_sel,
    input s5_ack,
    output s5_stb,
    output s5_cyc,
    output s5_we,
    input s5_int,  // IJB. Nothing to connect this too!! No IRQ controller on x300.

    // AXI_DRAM_FIFO BIST. Not for production.
    output bist_start,
    output [15:0] bist_control,
    input bist_done,
    input bist_fail,


   // Debug
    input [3:0] fifo_flags,
    output [31:0] debug0,
    output [31:0] debug1,
    output [127:0] debug2);

   localparam SR_AWIDTH = 8;
   localparam RB_AWIDTH = 8;

   localparam SR_LEDS       = 8'd00;
   localparam SR_SW_RST     = 8'd01;
   localparam SR_CLOCK_CTRL = 8'd02;
   localparam SR_XB_LOCAL   = 8'd03;
   localparam SR_SFPP_CTRL0 = 8'd08;
   localparam SR_SFPP_CTRL1 = 8'd09;
   localparam SR_FIFOFLAGS  = 8'd10;
   localparam SR_SPI        = 8'd32;
   localparam SR_ETHINT0    = 8'd40;
   localparam SR_ETHINT1    = 8'd56;
   // For AXI_DRAM_FIFO debug, not production
   localparam SR_BIST       = 8'd128;


   localparam RB_COUNTER      = 8'd00;
   localparam RB_SPI_RDY      = 8'd01;
   localparam RB_SPI_DATA     = 8'd02;
   localparam RB_CLK_STATUS   = 8'd03;
   localparam RB_ETH_TYPE0    = 8'd04;
   localparam RB_ETH_TYPE1    = 8'd05;
   localparam RB_COMPAT_NUM   = 8'd06;

   localparam RB_SFPP_STATUS0 = 8'd08;
   localparam RB_SFPP_STATUS1 = 8'd09;
   localparam RB_FIFOFLAGS    = 8'd10;
   localparam RB_CROSSBAR     = 8'd64; // Block of 64 addresses start here.
   // For AXI_DRAM_FIFO debug, not production
   localparam RB_BIST         = 8'd128;


   localparam COMPAT_MAJOR    = 16'h0004;
   localparam COMPAT_MINOR    = 16'h0000;

   wire [31:0] 	  set_data;
   wire [7:0] 	  set_addr;
   reg [31:0] 	  rb_data;
   wire [RB_AWIDTH-1:0] rb_addr;
   wire 		rb_rd_stb;
   wire 	  set_stb;
   wire 	  spi_ready;
   wire [31:0] 	  rb_spi_data;
   wire [17:0] 	  eth_debug_flags;


   // ZPU in and ZPU out axi streams
   wire [63:0] 	  zpui_tdata, zpuo_tdata;
   wire [3:0] 	  zpui_tuser, zpuo_tuser;
   wire 	  zpui_tlast, zpuo_tlast, zpui_tvalid, zpuo_tvalid, zpui_tready, zpuo_tready;
   wire [63:0] 	  zpui0_tdata, zpuo0_tdata;
   wire [3:0] 	  zpui0_tuser, zpuo0_tuser;
   wire 	  zpui0_tlast, zpuo0_tlast, zpui0_tvalid, zpuo0_tvalid, zpui0_tready, zpuo0_tready;
   wire [63:0] 	  zpui1_tdata, zpuo1_tdata;
   wire [3:0] 	  zpui1_tuser, zpuo1_tuser;
   wire 	  zpui1_tlast, zpuo1_tlast, zpui1_tvalid, zpuo1_tvalid, zpui1_tready, zpuo1_tready;

   // v2e (vita to ethernet) and e2v (eth to vita)
   wire [63:0] 	  v2e0_tdata, v2e1_tdata, e2v0_tdata, e2v1_tdata;
   wire 	  v2e0_tlast, v2e1_tlast, v2e0_tvalid, v2e1_tvalid, v2e0_tready, v2e1_tready;
   wire 	  e2v0_tlast, e2v1_tlast, e2v0_tvalid, e2v1_tvalid, e2v0_tready, e2v1_tready;

   //settings bus for crossbar router
   wire [31:0] 	  set_data_xb;
   wire [8:0] 	  set_addr_xb;
   wire 	  set_stb_xb;

   // SFP+ logic
   reg 		  SFPP0_ModAbs_reg, SFPP0_TxFault_reg,SFPP0_RxLOS_reg;
   reg 		  SFPP0_ModAbs_reg2, SFPP0_TxFault_reg2,SFPP0_RxLOS_reg2;
   reg 		  SFPP0_ModAbs_chgd, SFPP0_TxFault_chgd, SFPP0_RxLOS_chgd;

   reg 		  SFPP1_ModAbs_reg, SFPP1_TxFault_reg,SFPP1_RxLOS_reg;
   reg 		  SFPP1_ModAbs_reg2, SFPP1_TxFault_reg2,SFPP1_RxLOS_reg2;
   reg 		  SFPP1_ModAbs_chgd, SFPP1_TxFault_chgd, SFPP1_RxLOS_chgd;


   ////////////////////////////////////////////////////////////////////
   // Soft CPU - drives network setup, soft reset, ICMP, ...
   ////////////////////////////////////////////////////////////////////
   soft_ctrl #(.SB_ADDRW(SR_AWIDTH), .RB_ADDRW(RB_AWIDTH)) sc
     (
      .clk(clk), .rst(reset),
      //------------------------------------------------------------------
      // I2C interfaces
      //------------------------------------------------------------------
      .scl0(scl0), .sda0(sda0),
      .scl1(scl1), .sda1(sda1),
      .scl2(scl2), .sda2(sda2),
      //------------------------------------------------------------------
      // UARTs for CPU comms
      //------------------------------------------------------------------
      .gps_rxd(gps_rxd), .gps_txd(gps_txd),
      .debug_rxd(debug_rxd), .debug_txd(debug_txd),
      //------------------------------------------------------------------
      // settings bus interface
      //------------------------------------------------------------------
      .set_stb(set_stb),
      .set_addr(set_addr),
      .set_data(set_data),
      //------------------------------------------------------------------
      // settings bus interface for crossbar router
      //------------------------------------------------------------------
      .set_stb_xb(set_stb_xb),
      .set_addr_xb(set_addr_xb),
      .set_data_xb(set_data_xb),
      //------------------------------------------------------------------
      // readback bus interface
      //------------------------------------------------------------------
      .rb_addr(rb_addr),
      .rb_data(rb_data),
      .rb_rd_stb(rb_rd_stb),
      //------------------------------------------------------------------
      // packet interface in
      //------------------------------------------------------------------
      .rx_tdata(zpui_tdata),
      .rx_tuser(zpui_tuser),
      .rx_tlast(zpui_tlast),
      .rx_tvalid(zpui_tvalid),
      .rx_tready(zpui_tready),
      //------------------------------------------------------------------
      // packet interface out
      //------------------------------------------------------------------
      .tx_tdata(zpuo_tdata),
      .tx_tuser(zpuo_tuser),
      .tx_tlast(zpuo_tlast),
      .tx_tvalid(zpuo_tvalid),
      .tx_tready(zpuo_tready),
      //------------------------------------------------------------------
      // Wishbone Slave Interface(s)
      //------------------------------------------------------------------
      .s4_dat_i(s4_dat_i),
      .s4_dat_o(s4_dat_o),
      .s4_adr(s4_adr),
      .s4_sel(s4_sel),
      .s4_ack(s4_ack),
      .s4_stb(s4_stb),
      .s4_cyc(s4_cyc),
      .s4_we(s4_we),
      .s4_int(s4_int),
      //------------------------------------------------------------------
      // IoPort2 Msg Interface
      //------------------------------------------------------------------
      .o_iop2_msg_tdata(o_iop2_msg_tdata),
      .o_iop2_msg_tvalid(o_iop2_msg_tvalid),
      .o_iop2_msg_tlast(o_iop2_msg_tlast),
      .o_iop2_msg_tready(o_iop2_msg_tready),
      .i_iop2_msg_tdata(i_iop2_msg_tdata),
      .i_iop2_msg_tvalid(i_iop2_msg_tvalid),
      .i_iop2_msg_tlast(i_iop2_msg_tlast),
      .i_iop2_msg_tready(i_iop2_msg_tready),

      .s5_dat_i(s5_dat_i),
      .s5_dat_o(s5_dat_o),
      .s5_adr(s5_adr),
      .s5_sel(s5_sel),
      .s5_ack(s5_ack),
      .s5_stb(s5_stb),
      .s5_cyc(s5_cyc),
      .s5_we(s5_we),
      .s5_int(s5_int),

      //------------------------------------------------------------------
      // Debug
      //------------------------------------------------------------------
      .debug0(debug2),
      .debug1()
      );

   setting_reg #(.my_addr(SR_LEDS), .awidth(SR_AWIDTH), .width(8)) set_leds
     (.clk(clk), .rst(reset),
      .strobe(set_stb), .addr(set_addr), .in(set_data),
      .out(leds));

   //
   // SW_RST - Bit allocation:
   // [0] - PHY reset
   // [1] - Radio clk domain reset
   // [2] - Radio Clk PLL reset.
   // [3] - Usused.
   //
   setting_reg #(.my_addr(SR_SW_RST), .awidth(SR_AWIDTH), .width(4)) set_sw_rst
     (.clk(clk), .rst(reset),
      .strobe(set_stb), .addr(set_addr), .in(set_data),
      .out(sw_rst));

   setting_reg #(.my_addr(SR_CLOCK_CTRL), .awidth(SR_AWIDTH), .width(7),
        .at_reset(7'b1000000) //bit 6 high means GPSDO on by default
    ) set_clk_ctrl
     (.clk(clk), .rst(reset),
      .strobe(set_stb), .addr(set_addr), .in(set_data),
      .out(clock_control));

   simple_spi_core #(.BASE(SR_SPI), .WIDTH(1), .CLK_IDLE(0), .SEN_IDLE(1'b1)) misc_spi
     (.clock(clk), .reset(reset),
      .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
      .readback(rb_spi_data), .ready(spi_ready),
      .sen(sen), .sclk(sclk), .mosi(mosi), .miso(miso),
      .debug());

   //
   // Provide instrumentation so that abnormal FIFO conditions can be identifed.
   //
   wire 	  clear_debug_flags;
   reg [31:0] 	  debug_flags;

   setting_reg #(.my_addr(SR_FIFOFLAGS), .awidth(16), .width(1)) sr_reset_fifo_debug
     (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
      .in(set_data),.out(),.changed(clear_debug_flags));

   always @(posedge clk)
     if (reset)
       debug_flags <= 0;
     else if (clear_debug_flags)
       debug_flags <= 0;
     else
       debug_flags <= debug_flags | {
				     10'h0,
				     ~fifo_flags[3:0],
				     eth_debug_flags};

   reg [31:0] 	  counter;
   wire [31:0] 	  rb_data_crossbar;

   always @(posedge clk) counter <= counter + 1;

   always @*
     casex (rb_addr)
       RB_COMPAT_NUM: rb_data = {COMPAT_MAJOR, COMPAT_MINOR};
       RB_COUNTER: rb_data = counter;
       RB_SPI_RDY: rb_data = {31'b0, spi_ready};
       RB_SPI_DATA: rb_data = rb_spi_data;
       RB_CLK_STATUS: rb_data = {27'b0, clock_status};
       // SFPP Interface pins.
       RB_SFPP_STATUS0: rb_data = {26'b0,SFPP0_ModAbs_chgd,SFPP0_TxFault_chgd,SFPP0_RxLOS_chgd,
				  SFPP0_ModAbs_reg2,SFPP0_TxFault_reg2,SFPP0_RxLOS_reg2};
       RB_SFPP_STATUS1: rb_data = {26'b0,SFPP1_ModAbs_chgd,SFPP1_TxFault_chgd,SFPP1_RxLOS_chgd,
				  SFPP1_ModAbs_reg2,SFPP1_TxFault_reg2,SFPP1_RxLOS_reg2};
       // Allow readback of configured ethernet interfaces.
`ifdef ETH10G_PORT0
       RB_ETH_TYPE0: rb_data = {32'h1};
`else
       RB_ETH_TYPE0: rb_data = {32'h0};
`endif
`ifdef ETH10G_PORT1
       RB_ETH_TYPE1: rb_data = {32'h1};
`else
       RB_ETH_TYPE1: rb_data = {32'h0};
`endif
       // Read FIFO status from Ethernet Interfaces
       RB_FIFOFLAGS: rb_data = debug_flags;

       (RB_CROSSBAR | 6'bxxxxxx): rb_data = rb_data_crossbar;
       // AXI_DRAM_FIFO BIST. Not for production.
       RB_BIST: rb_data = {29'h0,bist_done,bist_fail,bist_start};


       default: rb_data = 32'h0;
     endcase // case (rb_addr)

   // AXI_DRAM_FIFO BIST. Not for production.
   setting_reg #(.my_addr(SR_BIST), .awidth(SR_AWIDTH), .width(17)) set_bist_start
     (.clk(clk), .rst(reset),
      .strobe(set_stb), .addr(set_addr), .in(set_data),
      .out({bist_start,bist_control}));

   // Latch state changes to SFP+ pins.
   always @(posedge clk)
     begin
	SFPP0_ModAbs_reg <= SFPP0_ModAbs;
	SFPP0_TxFault_reg <= SFPP0_TxFault;
	SFPP0_RxLOS_reg <= SFPP0_RxLOS;
	SFPP0_ModAbs_reg2 <= SFPP0_ModAbs_reg;
	SFPP0_TxFault_reg2 <= SFPP0_TxFault_reg;
	SFPP0_RxLOS_reg2 <= SFPP0_RxLOS_reg;
	if (rb_rd_stb && (rb_addr == RB_SFPP_STATUS0) ) begin
	   SFPP0_ModAbs_chgd <= 1'b0;
	   SFPP0_TxFault_chgd <= 1'b0;
	   SFPP0_RxLOS_chgd <= 1'b0;
	end else begin
	   if (SFPP0_ModAbs_reg2 != SFPP0_ModAbs_reg)
	     SFPP0_ModAbs_chgd <= 1'b1;
	   if (SFPP0_TxFault_reg2 != SFPP0_TxFault_reg)
	     SFPP0_TxFault_chgd <= 1'b1;
	   if (SFPP0_RxLOS_reg2 != SFPP0_RxLOS_reg)
	     SFPP0_RxLOS_chgd <= 1'b1;
	end // else: !if(rb_rd_stb && (rb_addr == RB_SFPP_STATUS0) )
     end

   always @(posedge clk)
     begin
	SFPP1_ModAbs_reg <= SFPP1_ModAbs;
	SFPP1_TxFault_reg <= SFPP1_TxFault;
	SFPP1_RxLOS_reg <= SFPP1_RxLOS;
	SFPP1_ModAbs_reg2 <= SFPP1_ModAbs_reg;
	SFPP1_TxFault_reg2 <= SFPP1_TxFault_reg;
	SFPP1_RxLOS_reg2 <= SFPP1_RxLOS_reg;
	if (rb_rd_stb && (rb_addr == RB_SFPP_STATUS1) ) begin
	   SFPP1_ModAbs_chgd <= 1'b0;
	   SFPP1_TxFault_chgd <= 1'b0;
	   SFPP1_RxLOS_chgd <= 1'b0;
	end else begin
	   if (SFPP1_ModAbs_reg2 != SFPP1_ModAbs_reg)
	     SFPP1_ModAbs_chgd <= 1'b1;
	   if (SFPP1_TxFault_reg2 != SFPP1_TxFault_reg)
	     SFPP1_TxFault_chgd <= 1'b1;
	   if (SFPP1_RxLOS_reg2 != SFPP1_RxLOS_reg)
	     SFPP1_RxLOS_chgd <= 1'b1;
	end // else: !if(rb_rd_stb && (rb_addr == RB_SFPP_STATUS1) )
     end

   wire [1:0] 	  sfpp0_ctrl;

   // SFPP_RS0/1 pins are open drain.
   setting_reg #(.my_addr(SR_SFPP_CTRL0), .awidth(SR_AWIDTH), .width(2), .at_reset(2'b00)) set_sfpp0_ctrl
     (.clk(clk), .rst(reset),
      .strobe(set_stb), .addr(set_addr), .in(set_data),
      .out(sfpp0_ctrl));

   assign SFPP0_RS0 = sfpp0_ctrl[0] ? 1'b0 : 1'bz;
   assign SFPP0_RS1 = sfpp0_ctrl[1] ? 1'b0 : 1'bz;

  wire [1:0] 	  sfpp1_ctrl;

   // SFPP1_RS0/1 pins are open drain.
   setting_reg #(.my_addr(SR_SFPP_CTRL1), .awidth(SR_AWIDTH), .width(2), .at_reset(2'b00)) set_sfpp1_ctrl
     (.clk(clk), .rst(reset),
      .strobe(set_stb), .addr(set_addr), .in(set_data),
      .out(sfpp1_ctrl));

   assign SFPP1_RS0 = sfpp1_ctrl[0] ? 1'b0 : 1'bz;
   assign SFPP1_RS1 = sfpp1_ctrl[1] ? 1'b0 : 1'bz;


   //assign debug = { 9'b0, set_stb, spi_ready, i2c_ready, sen, sclk, mosi, miso, set_addr[7:0], state[7:0]};

   // ////////////////////////////////////////////////////////////////
   // ETH interfaces

   wire [63:0] 	  e01_tdata, e10_tdata;
   wire [3:0] 	  e01_tuser, e10_tuser;
   wire 	  e01_tlast, e01_tvalid, e01_tready;
   wire 	  e10_tlast, e10_tvalid, e10_tready;

   eth_interface #(.BASE(SR_ETHINT0)) eth_interface0
     (.clk(clk), .reset(reset), .clear(clear),
      .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
      .eth_tx_tdata(eth0_tx_tdata), .eth_tx_tuser(eth0_tx_tuser), .eth_tx_tlast(eth0_tx_tlast),
      .eth_tx_tvalid(eth0_tx_tvalid), .eth_tx_tready(eth0_tx_tready),
      .eth_rx_tdata(eth0_rx_tdata), .eth_rx_tuser(eth0_rx_tuser), .eth_rx_tlast(eth0_rx_tlast),
      .eth_rx_tvalid(eth0_rx_tvalid), .eth_rx_tready(eth0_rx_tready),
      .e2v_tdata(e2v0_tdata), .e2v_tlast(e2v0_tlast), .e2v_tvalid(e2v0_tvalid), .e2v_tready(e2v0_tready),
      .v2e_tdata(v2e0_tdata), .v2e_tlast(v2e0_tlast), .v2e_tvalid(v2e0_tvalid), .v2e_tready(v2e0_tready),
      .xo_tdata(e01_tdata), .xo_tuser(e01_tuser), .xo_tlast(e01_tlast), .xo_tvalid(e01_tvalid), .xo_tready(e01_tready),
      .xi_tdata(e10_tdata), .xi_tuser(e10_tuser), .xi_tlast(e10_tlast), .xi_tvalid(e10_tvalid), .xi_tready(e10_tready),
      .e2z_tdata(zpui0_tdata), .e2z_tuser(zpui0_tuser), .e2z_tlast(zpui0_tlast), .e2z_tvalid(zpui0_tvalid), .e2z_tready(zpui0_tready),
      .z2e_tdata(zpuo0_tdata), .z2e_tuser(zpuo0_tuser), .z2e_tlast(zpuo0_tlast), .z2e_tvalid(zpuo0_tvalid), .z2e_tready(zpuo0_tready),
      .debug_flags(eth_debug_flags[8:0]),.debug(/*debug2*/));

   eth_interface #(.BASE(SR_ETHINT1)) eth_interface1
     (.clk(clk), .reset(reset), .clear(clear),
      .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
      .eth_tx_tdata(eth1_tx_tdata), .eth_tx_tuser(eth1_tx_tuser), .eth_tx_tlast(eth1_tx_tlast),
      .eth_tx_tvalid(eth1_tx_tvalid), .eth_tx_tready(eth1_tx_tready),
      .eth_rx_tdata(eth1_rx_tdata), .eth_rx_tuser(eth1_rx_tuser), .eth_rx_tlast(eth1_rx_tlast),
      .eth_rx_tvalid(eth1_rx_tvalid), .eth_rx_tready(eth1_rx_tready),
      .e2v_tdata(e2v1_tdata), .e2v_tlast(e2v1_tlast), .e2v_tvalid(e2v1_tvalid), .e2v_tready(e2v1_tready),
      .v2e_tdata(v2e1_tdata), .v2e_tlast(v2e1_tlast), .v2e_tvalid(v2e1_tvalid), .v2e_tready(v2e1_tready),
      .xo_tdata(e10_tdata), .xo_tuser(e10_tuser), .xo_tlast(e10_tlast), .xo_tvalid(e10_tvalid), .xo_tready(e10_tready),
      .xi_tdata(e01_tdata), .xi_tuser(e01_tuser), .xi_tlast(e01_tlast), .xi_tvalid(e01_tvalid), .xi_tready(e01_tready),
      .e2z_tdata(zpui1_tdata), .e2z_tuser(zpui1_tuser), .e2z_tlast(zpui1_tlast), .e2z_tvalid(zpui1_tvalid), .e2z_tready(zpui1_tready),
      .z2e_tdata(zpuo1_tdata), .z2e_tuser(zpuo1_tuser), .z2e_tlast(zpuo1_tlast), .z2e_tvalid(zpuo1_tvalid), .z2e_tready(zpuo1_tready),
      .debug_flags(eth_debug_flags[17:9]),.debug());

   axi_mux4 #(.PRIO(0), .WIDTH(68)) zpui_mux
     (.clk(clk), .reset(reset), .clear(clear),
      .i0_tdata({zpui0_tuser,zpui0_tdata}), .i0_tlast(zpui0_tlast), .i0_tvalid(zpui0_tvalid), .i0_tready(zpui0_tready),
      .i1_tdata({zpui1_tuser,zpui1_tdata}), .i1_tlast(zpui1_tlast), .i1_tvalid(zpui1_tvalid), .i1_tready(zpui1_tready),
      .i2_tdata(68'h0), .i2_tlast(1'b0), .i2_tvalid(1'b0), .i2_tready(),
      .i3_tdata(68'h0), .i3_tlast(1'b0), .i3_tvalid(1'b0), .i3_tready(),
      .o_tdata({zpui_tuser,zpui_tdata}), .o_tlast(zpui_tlast), .o_tvalid(zpui_tvalid), .o_tready(zpui_tready));

   // Demux ZPU to Eth output by the port number in top 8 bits of data on first line
   wire [67:0] 	  zpuo_eth_header;
   wire [1:0] 	  zpuo_eth_dest = (zpuo_eth_header[63:56] == 8'd0) ? 2'b00 : 2'b01;

   axi_demux4 #(.ACTIVE_CHAN(4'b0011), .WIDTH(68)) zpuo_demux
     (.clk(clk), .reset(reset), .clear(clear),
      .header(zpuo_eth_header), .dest(zpuo_eth_dest),
      .i_tdata({zpuo_tuser,zpuo_tdata}), .i_tlast(zpuo_tlast), .i_tvalid(zpuo_tvalid), .i_tready(zpuo_tready),
      .o0_tdata({zpuo0_tuser,zpuo0_tdata}), .o0_tlast(zpuo0_tlast), .o0_tvalid(zpuo0_tvalid), .o0_tready(zpuo0_tready),
      .o1_tdata({zpuo1_tuser,zpuo1_tdata}), .o1_tlast(zpuo1_tlast), .o1_tvalid(zpuo1_tvalid), .o1_tready(zpuo1_tready),
      .o2_tdata(), .o2_tlast(), .o2_tvalid(), .o2_tready(1'b1),
      .o3_tdata(), .o3_tlast(), .o3_tvalid(), .o3_tready(1'b1));

   // //////////////////////////////////////////////////////////////////////
   // axi_crossbar ports
   // 0 - ETH0
   // 1 - ETH1
   // 2 - Radio0
   // 3 - Radio1
   // 4 - CE0
   // 5 - CE1
   // 6 - CE2
   // 7 - PCIe

    wire [7:0] 		 local_addr;

   setting_reg #(.my_addr(SR_XB_LOCAL), .awidth(SR_AWIDTH), .width(8)) sr_local_addr
     (.clk(clk),.rst(reset),.strobe(set_stb),.addr(set_addr),
      .in(set_data),.out(local_addr),.changed());


   localparam 		 CROSSBAR_IN = 8;
   localparam 		 CROSSBAR_OUT = 8;

   axi_crossbar #(.FIFO_WIDTH(64), .DST_WIDTH(16), .NUM_INPUTS(CROSSBAR_IN), .NUM_OUTPUTS(CROSSBAR_OUT)) axi_crossbar
     (.clk(clk), .reset(reset), .clear(0),
      .local_addr(local_addr),
      .set_stb(set_stb_xb), .set_addr(set_addr_xb), .set_data(set_data_xb),
      .i_tdata({pcii_tdata,ce2i_tdata,ce1i_tdata,ce0i_tdata,r1i_tdata,r0i_tdata,e2v1_tdata,e2v0_tdata}),
      .i_tlast({pcii_tlast,ce2i_tlast,ce1i_tlast,ce0i_tlast,r1i_tlast,r0i_tlast,e2v1_tlast,e2v0_tlast}),
      .i_tvalid({pcii_tvalid,ce2i_tvalid,ce1i_tvalid,ce0i_tvalid,r1i_tvalid,r0i_tvalid,e2v1_tvalid,e2v0_tvalid}),
      .i_tready({pcii_tready,ce2i_tready,ce1i_tready,ce0i_tready,r1i_tready,r0i_tready,e2v1_tready,e2v0_tready}),
      .o_tdata({pcio_tdata,ce2o_tdata,ce1o_tdata,ce0o_tdata,r1o_tdata,r0o_tdata,v2e1_tdata,v2e0_tdata}),
      .o_tlast({pcio_tlast,ce2o_tlast,ce1o_tlast,ce0o_tlast,r1o_tlast,r0o_tlast,v2e1_tlast,v2e0_tlast}),
      .o_tvalid({pcio_tvalid,ce2o_tvalid,ce1o_tvalid,ce0o_tvalid,r1o_tvalid,r0o_tvalid,v2e1_tvalid,v2e0_tvalid}),
      .o_tready({pcio_tready,ce2o_tready,ce1o_tready,ce0o_tready,r1o_tready,r0o_tready,v2e1_tready,v2e0_tready}),
      .pkt_present({pcii_tvalid,ce2i_tvalid,ce1i_tvalid,ce0i_tvalid,r1i_tvalid,r0i_tvalid,e2v1_tvalid,e2v0_tvalid}),
      .rb_rd_stb(rb_rd_stb && ((rb_addr >> (`LOG2(NUM_OUTPUTS)+`LOG2(NUM_INPUTS))) == RB_CROSSBAR >> (`LOG2(NUM_OUTPUTS)+`LOG2(NUM_INPUTS)))),
      .rb_addr(rb_addr[`LOG2(CROSSBAR_IN)+`LOG2(CROSSBAR_OUT)-1:0]), .rb_data(rb_data_crossbar)
      );

/*
assign debug2 = {
        pcii_tdata[31:0],                                                                                   //[127:92]
        pcio_tdata[31:0],                                                                                   //[91:64]
        local_addr[5:0],                                                                                    //[63:58]
        set_stb_xb,                                                                                         //[57]
        set_addr_xb,                                                                                        //[56:48]
        pcii_tvalid,ce2i_tvalid,ce1i_tvalid,ce0i_tvalid,r1i_tvalid,r0i_tvalid,e2v1_tvalid,e2v0_tvalid,      //[47:40]
        pcii_tready,ce2i_tready,ce1i_tready,ce0i_tready,r1i_tready,r0i_tready,e2v1_tready,e2v0_tready,      //[39:32]
        pcii_tlast,ce2i_tlast,ce1i_tlast,ce0i_tlast,r1i_tlast,r0i_tlast,e2v1_tlast,e2v0_tlast,              //[31:24]
        pcio_tvalid,ce2o_tvalid,ce1o_tvalid,ce0o_tvalid,r1o_tvalid,r0o_tvalid,v2e1_tvalid,v2e0_tvalid,      //[23:16]
        pcio_tready,ce2o_tready,ce1o_tready,ce0o_tready,r1o_tready,r0o_tready,v2e1_tready,v2e0_tready,      //[15:8]
        pcio_tlast,ce2o_tlast,ce1o_tlast,ce0o_tlast,r1o_tlast,r0o_tlast,v2e1_tlast,v2e0_tlast               //[7:0]
	 };
*/
   //
   // This next section adds the ability to send messages and data via chipscope and the setting bus.
   // If chipscope is used elsewhere in the hierarchy then this must be commented.
   //
/* -----\/----- EXCLUDED -----\/-----
   wire [35:0] 		 CONTROL0;
   (* keep = "true", max_fanout = 10 *)   reg [31:0] 		 set_data_debug;
   (* keep = "true", max_fanout = 10 *)   reg [7:0] 		 set_addr_debug;
   (* keep = "true", max_fanout = 10 *)   reg 			 set_stb_debug;

   always @(posedge clk) begin
      set_data_debug = set_data;
      set_addr_debug = set_addr;
      set_stb_debug = set_stb;
   end

   chipscope_icon chipscope_icon_i0
     (
      .CONTROL0(CONTROL0) // INOUT BUS [35:0]
      );

   chipscope_ila_64 chipscope_ila_i0
     (
      .CONTROL(CONTROL0), // INOUT BUS [35:0]
      .CLK(clk), // IN
      .TRIG0(
	     {
	      set_stb_debug,       // [40]
	      set_addr_debug[7:0], // [39:32]
	      set_data_debug[31:0] // [31:0]
	      })
      );
 -----/\----- EXCLUDED -----/\----- */


   // Fixed connections
/* -----\/----- EXCLUDED -----\/-----
   assign { r0o_tvalid, r0o_tlast, r0o_tdata } = { e2v0_tvalid, e2v0_tlast, e2v0_tdata };
   assign e2v0_tready = r0o_tready;

   assign { v2e0_tvalid, v2e0_tlast, v2e0_tdata } = { r0i_tvalid, r0i_tlast, r0i_tdata };
   assign r0i_tready = v2e0_tready;
 -----/\----- EXCLUDED -----/\----- */

/*
    assign debug2 = {
        eth0_tx_tvalid, eth0_tx_tready,
        eth0_rx_tvalid, eth0_rx_tready,
        e2v0_tvalid, e2v0_tready,
        v2e0_tvalid, v2e0_tready,

        e01_tvalid, e01_tready,
        e10_tvalid, e10_tready,
        zpui0_tvalid, zpui0_tready,
        zpuo0_tvalid, zpuo0_tready,

        zpuo_tvalid, zpuo_tready,
        zpui_tvalid, zpui_tready,
        4'b0,

        8'b0
    };
*/
endmodule // bus_int