diff options
Diffstat (limited to 'usrp2/top')
| -rw-r--r-- | usrp2/top/u1e/Makefile | 2 | ||||
| -rw-r--r-- | usrp2/top/u1e/u1e_core.v | 75 |
2 files changed, 44 insertions, 33 deletions
diff --git a/usrp2/top/u1e/Makefile b/usrp2/top/u1e/Makefile index 2b78b21bd..a0f921485 100644 --- a/usrp2/top/u1e/Makefile +++ b/usrp2/top/u1e/Makefile @@ -54,7 +54,7 @@ simulator "ISE Simulator (VHDL/Verilog)" \ export SOURCE_ROOT := ../../../ export SOURCES := \ control_lib/CRC16_D16.v \ -control_lib/atr_controller.v \ +control_lib/atr_controller16.v \ control_lib/bin2gray.v \ control_lib/dcache.v \ control_lib/decoder_3_8.v \ diff --git a/usrp2/top/u1e/u1e_core.v b/usrp2/top/u1e/u1e_core.v index f2415d7e1..e692cbc3d 100644 --- a/usrp2/top/u1e/u1e_core.v +++ b/usrp2/top/u1e/u1e_core.v @@ -147,48 +147,52 @@ module u1e_core .sf_dat_o(sf_dat_mosi),.sf_adr_o(sf_adr),.sf_sel_o(sf_sel),.sf_we_o(sf_we),.sf_cyc_o(sf_cyc),.sf_stb_o(sf_stb), .sf_dat_i(sf_dat_miso),.sf_ack_i(sf_ack),.sf_err_i(0),.sf_rty_i(0) ); - assign s6_ack = 0; assign s7_ack = 0; + assign s7_ack = 0; assign s8_ack = 0; assign s9_ack = 0; assign sa_ack = 0; assign sb_ack = 0; assign sc_ack = 0; assign sd_ack = 0; assign se_ack = 0; assign sf_ack = 0; // ///////////////////////////////////////////////////////////////////////////////////// // Slave 0, Misc LEDs, Switches, controls - reg [15:0] reg_fast, reg_slow; - localparam REG_FAST = 7'd4; - localparam REG_SWITCHES = 7'd6; - localparam REG_GPIOS = 7'd8; - localparam REG_CGEN_ST = 7'd9; - localparam REG_CGEN_CTRL = 7'd10; + reg [15:0] reg_leds, reg_cgen_ctrl, reg_test; - reg [3:0] reg_gpios; - - always @(posedge wb_clk) - if(s0_cyc & s0_stb & s0_we & (s0_adr[6:0] == REG_FAST)) - reg_fast <= s0_dat_mosi; - - always @(posedge wb_clk) - if(s0_cyc & s0_stb & s0_we & (s0_adr[6:0] == REG_GPIOS)) - reg_gpios <= s0_dat_mosi; - - reg [1:0] reg_cgen_ctrls; + localparam REG_LEDS = 7'd0; // out + localparam REG_SWITCHES = 7'd2; // in + localparam REG_CGEN_CTRL = 7'd4; // out + localparam REG_CGEN_ST = 7'd6; // in + localparam REG_TEST = 7'd8; // out always @(posedge wb_clk) if(wb_rst) - reg_cgen_ctrls <= 2'b11; - else if(s0_cyc & s0_stb & s0_we & (s0_adr[6:0] == REG_CGEN_CTRL)) - reg_cgen_ctrls <= s0_dat_mosi; + begin + reg_leds <= 0; + reg_cgen_ctrl <= 2'b11; + reg_test <= 0; + end + else + if(s0_cyc & s0_stb & s0_we) + case(s0_adr[6:0]) + REG_LEDS : + reg_leds <= s0_dat_mosi; + REG_CGEN_CTRL : + reg_cgen_ctrl <= s0_dat_mosi; + REG_TEST : + reg_test <= s0_dat_mosi; + endcase // case (s0_adr[6:0]) - assign {cgen_sync_b, cgen_ref_sel} = reg_cgen_ctrls; + assign { debug_led[2],debug_led[0],debug_led[1] } = reg_leds; // LEDs are arranged funny on board + assign { cgen_sync_b, cgen_ref_sel } = reg_cgen_ctrl; + assign { rx_overrun, tx_undderun } = reg_test; - assign s0_dat_miso = (s0_adr[6:0] == REG_FAST) ? reg_fast : + assign s0_dat_miso = (s0_adr[6:0] == REG_LEDS) ? reg_leds : (s0_adr[6:0] == REG_SWITCHES) ? {5'b0,debug_pb[2:0],dip_sw[7:0]} : + (s0_adr[6:0] == REG_CGEN_CTRL) ? reg_cgen_ctrl : (s0_adr[6:0] == REG_CGEN_ST) ? {13'b0,cgen_st_status,cgen_st_ld,cgen_st_refmon} : + (s0_adr[6:0] == REG_TEST) ? reg_test : 16'hBEEF; + assign s0_ack = s0_stb & s0_cyc; - assign { rx_overrun, tx_underrun } = reg_gpios; - // ///////////////////////////////////////////////////////////////////////////////////// // Slave 1, UART // depth of 3 is 128 entries, clkdiv of 278 gives 230.4k with a 64 MHz system clock @@ -196,7 +200,7 @@ module u1e_core simple_uart #(.TXDEPTH(3),.RXDEPTH(3), .CLKDIV_DEFAULT(278)) uart (.clk_i(wb_clk),.rst_i(wb_rst), .we_i(s1_we),.stb_i(s1_stb),.cyc_i(s1_cyc),.ack_o(s1_ack), - .adr_i(s1_adr[4:2]),.dat_i({16'd0,s1_dat_mosi}),.dat_o(s1_dat_miso), + .adr_i(s1_adr[3:1]),.dat_i({16'd0,s1_dat_mosi}),.dat_o(s1_dat_miso), .rx_int_o(),.tx_int_o(), .tx_o(debug_txd),.rx_i(debug_rxd),.baud_o()); @@ -246,16 +250,25 @@ module u1e_core wire [7:0] set_addr; wire [31:0] set_data; wire set_stb; - - settings_bus_16LE settings_bus_16LE + + // only have 32 regs, 32 bits each with current setup... + settings_bus_16LE #(.AWIDTH(11),.RWIDTH(11-4-2)) settings_bus_16LE (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s5_adr),.wb_dat_i(s5_dat_mosi), .wb_stb_i(s5_stb),.wb_we_i(s5_we),.wb_ack_o(s5_ack), .strobe(set_stb),.addr(set_addr),.data(set_data) ); - // ///////////////////////////////////////////////////////////////////////////////////// - // Debug Pins + // ///////////////////////////////////////////////////////////////////////// + // ATR Controller -- Slave #6 + + atr_controller16 atr_controller16 + (.clk_i(wb_clk), .rst_i(wb_rst), + .adr_i(s6_adr), .sel_i(s6_sel), .dat_i(s6_dat_mosi), .dat_o(s6_dat_miso), + .we_i(s6_we), .stb_i(s6_stb), .cyc_i(s6_cyc), .ack_o(s6_ack), + .run_rx(), .run_tx(), .master_time(0), .ctrl_lines(atr_lines)); + // ///////////////////////////////////////////////////////////////////////////////////// // Debug circuitry + assign debug_clk = { EM_CLK, clk_fpga }; assign debug = { { rx_have_data, tx_have_space, EM_NCS6, EM_NCS4, EM_NWE, EM_NOE, EM_A[10:1] }, { EM_D } }; @@ -263,6 +276,4 @@ module u1e_core assign debug_gpio_0 = { debug_gpmc }; assign debug_gpio_1 = { debug_txd, debug_rxd }; - assign { debug_led[2],debug_led[0],debug_led[1] } = reg_fast; // LEDs are arranged funny on board - endmodule // u1e_core |