diff options
Diffstat (limited to 'host/lib')
| -rw-r--r-- | host/lib/usrp/usrp_e/usrp_e_regs.hpp | 131 |
1 files changed, 94 insertions, 37 deletions
diff --git a/host/lib/usrp/usrp_e/usrp_e_regs.hpp b/host/lib/usrp/usrp_e/usrp_e_regs.hpp index 219f459a5..edd87e649 100644 --- a/host/lib/usrp/usrp_e/usrp_e_regs.hpp +++ b/host/lib/usrp/usrp_e/usrp_e_regs.hpp @@ -1,49 +1,106 @@ + + +//////////////////////////////////////////////////////////////// // -// Copyright 2010 Ettus Research LLC -// -// This program is free software: you can redistribute it and/or modify -// it under the terms of the GNU General Public License as published by -// the Free Software Foundation, either version 3 of the License, or -// (at your option) any later version. -// -// This program is distributed in the hope that it will be useful, -// but WITHOUT ANY WARRANTY; without even the implied warranty of -// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -// GNU General Public License for more details. -// -// You should have received a copy of the GNU General Public License -// along with this program. If not, see <http://www.gnu.org/licenses/>. +// Memory map for embedded wishbone bus // +//////////////////////////////////////////////////////////////// + +// All addresses are byte addresses. All accesses are word (16-bit) accesses. +// This means that address bit 0 is usually 0. +// There are 11 bits of address for the control. + +#ifndef __USRP_E_REGS_H +#define __USRP_E_REGS_H + +///////////////////////////////////////////////////// +// Slave pointers + +#define UE_REG_SLAVE(n) ((n)<<7) + +///////////////////////////////////////////////////// +// Slave 0 -- Misc Regs + +#define UE_REG_MISC_BASE UE_REG_SLAVE(0) + +#define UE_REG_MISC_LED UE_REG_MISC_BASE + 0 +#define UE_REG_MISC_SW UE_REG_MISC_BASE + 2 +#define UE_REG_MISC_CGEN_CTRL UE_REG_MISC_BASE + 4 +#define UE_REG_MISC_CGEN_ST UE_REG_MISC_BASE + 6 +#define UE_REG_MISC_TEST UE_REG_MISC_BASE + 8 + +///////////////////////////////////////////////////// +// Slave 1 -- UART +// CLKDIV is 16 bits, others are only 8 + +#define UE_REG_UART_BASE UE_REG_SLAVE(1) -#ifndef INCLUDED_USRP_E_REGS_HPP -#define INCLUDED_USRP_E_REGS_HPP +#define UE_REG_UART_CLKDIV UE_REG_UART_BASE + 0 +#define UE_REG_UART_TXLEVEL UE_REG_UART_BASE + 2 +#define UE_REG_UART_RXLEVEL UE_REG_UART_BASE + 4 +#define UE_REG_UART_TXCHAR UE_REG_UART_BASE + 6 +#define UE_REG_UART_RXCHAR UE_REG_UART_BASE + 8 + +///////////////////////////////////////////////////// +// Slave 2 -- SPI Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_SPI_BASE UE_REG_SLAVE(2) -#include <boost/cstdint.hpp> //////////////////////////////////////////////// -// GPIO, Slave 4 -// -// These go to the daughterboard i/o pins +// Slave 3 -- I2C Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_I2C_BASE UE_REG_SLAVE(3) + + +//////////////////////////////////////////////// +// Slave 4 -- GPIO -#define GPIO_BASE 0x40 +#define UE_REG_GPIO_BASE UE_REG_SLAVE(4) -struct gpio_regs_t{ - boost::uint16_t rx_io; // tx data in high 16, rx in low 16 - boost::uint16_t tx_io; - boost::uint16_t rx_ddr; // 32 bits, 1 means output. tx in high 16, rx in low 16 - boost::uint16_t tx_ddr; - boost::uint16_t tx_sel_low; // 16 2-bit fields select which source goes to TX DB - boost::uint16_t tx_sel_high; - boost::uint16_t rx_sel_low; // 16 2-bit fields select which source goes to RX DB - boost::uint16_t rx_sel_high; -}; +#define UE_REG_GPIO_RX_IO UE_REG_GPIO_BASE + 0 +#define UE_REG_GPIO_TX_IO UE_REG_GPIO_BASE + 2 +#define UE_REG_GPIO_RX_DDR UE_REG_GPIO_BASE + 4 +#define UE_REG_GPIO_TX_DDR UE_REG_GPIO_BASE + 6 +#define UE_REG_GPIO_RX_SEL UE_REG_GPIO_BASE + 8 +#define UE_REG_GPIO_TX_SEL UE_REG_GPIO_BASE + 10 +#define UE_REG_GPIO_RX_DBG UE_REG_GPIO_BASE + 12 +#define UE_REG_GPIO_TX_DBG UE_REG_GPIO_BASE + 14 // each 2-bit sel field is layed out this way -#define GPIO_SEL_SW 0 // if pin is an output, set by software in the io reg -#define GPIO_SEL_ATR 1 // if pin is an output, set by ATR logic -#define GPIO_SEL_DEBUG_0 2 // if pin is an output, debug lines from FPGA fabric -#define GPIO_SEL_DEBUG_1 3 // if pin is an output, debug lines from FPGA fabric +#define GPIO_SEL_SW 0 // if pin is an output, set by software in the io reg +#define GPIO_SEL_ATR 1 // if pin is an output, set by ATR logic +#define GPIO_SEL_DEBUG_0 0 // if pin is an output, debug lines from FPGA fabric +#define GPIO_SEL_DEBUG_1 1 // if pin is an output, debug lines from FPGA fabric + + +//////////////////////////////////////////////////// +// Slave 5 -- Settings Bus +// +// Output-only, no readback, 32 registers total +// Each register must be written 32 bits at a time +// First the address xxx_xx00 and then xxx_xx10 + +#define UE_REG_SETTINGS_BASE UE_REG_SLAVE(5) + +/////////////////////////////////////////////////// +// Slave 6 -- ATR Controller +// 16 regs + +#define UE_REG_ATR_BASE UE_REG_SLAVE(6) + +#define UE_REG_ATR_IDLE_RXSIDE UE_REG_ATR_BASE + 0 +#define UE_REG_ATR_IDLE_TXSIDE UE_REG_ATR_BASE + 2 +#define UE_REG_ATR_INTX_RXSIDE UE_REG_ATR_BASE + 4 +#define UE_REG_ATR_INTX_TXSIDE UE_REG_ATR_BASE + 6 +#define UE_REG_ATR_INRX_RXSIDE UE_REG_ATR_BASE + 8 +#define UE_REG_ATR_INRX_TXSIDE UE_REG_ATR_BASE + 10 +#define UE_REG_ATR_FULL_RXSIDE UE_REG_ATR_BASE + 12 +#define UE_REG_ATR_FULL_TXSIDE UE_REG_ATR_BASE + 14 -//#define gpio_base ((gpio_regs_t *) GPIO_BASE) +#endif -#endif /* INCLUDED_USRP_E_REGS_HPP */ |