diff options
Diffstat (limited to 'host/include/uhd/rfnoc/blocks/ddc.xml')
| -rw-r--r-- | host/include/uhd/rfnoc/blocks/ddc.xml | 154 |
1 files changed, 0 insertions, 154 deletions
diff --git a/host/include/uhd/rfnoc/blocks/ddc.xml b/host/include/uhd/rfnoc/blocks/ddc.xml deleted file mode 100644 index 43e325c0e..000000000 --- a/host/include/uhd/rfnoc/blocks/ddc.xml +++ /dev/null @@ -1,154 +0,0 @@ -<!--This defines one NoC-Block.--> -<nocblock> - <name>Rx DSP (DDC/CORDIC)</name> - <blockname>DDC</blockname> - <key>DDC</key> - <!--There can be several of these:--> - <ids> - <id revision="0">DDC0000000000000</id> - </ids> - <!-- Registers --> - <registers> - <!-- AXI rate change block registers --> - <setreg> - <name>N</name> - <address>128</address> - </setreg> - <setreg> - <name>M</name> - <address>129</address> - </setreg> - <setreg> - <!-- 1 bit, enable clear user --> - <name>CONFIG</name> - <address>130</address> - </setreg> - <!-- DDC block registers --> - <setreg> - <!-- DDS phase increment word --> - <name>DDS_FREQ</name> - <address>132</address> - </setreg> - <setreg> - <!-- Scaling factor to compensate for gain through filters and CORDIC --> - <name>SCALE_IQ</name> - <address>133</address> - </setreg> - <setreg> - <!-- DDC control word, 10 bits total, 2 bits for Halfbands, 8 bits for CIC rate --> - <name>DECIM_WORD</name> - <address>134</address> - </setreg> - <setreg> - <!-- Real mode, swap IQ --> - <name>MODE</name> - <address>135</address> - </setreg> - <setreg> - <!-- Filter coefficients reload --> - <name>RELOAD</name> - <address>136</address> - </setreg> - </registers> - <!-- Args --> - <args> - <arg> - <name>freq</name> - <type>double</type> - <value>0.0</value> - <port>0</port> - <!--<action>--> - <!--SR_WRITE("CORDIC_FREQ", $cordic_freq)--> - <!--</action>--> - <!--FIXME Calculate this properly--> - </arg> - <arg> - <name>input_rate</name> - <type>double</type> - <value>1.0</value> - <port>0</port> - <check>GE($input_rate, 0.0)</check> - <check_message>The input rate must be a positive value (in Hz).</check_message> - </arg> - <arg> - <name>output_rate</name> - <type>double</type> - <value>1.0</value> - <port>0</port> - <check>GE($output_rate, 0.0)</check> - <check_message>The output rate must be a positive value (in Hz).</check_message> - </arg> - <arg> - <name>fullscale</name> - <type>double</type> - <value>1.0</value> - <port>0</port> - <check>GE($fullscale, 0.0)</check> - </arg> - <arg> - <name>scalar_correction</name> - <type>double</type> - <value>1.0</value> - <port>0</port> - </arg> - <arg> - <name>freq</name> - <type>double</type> - <value>0.0</value> - <port>1</port> - <!--<action>--> - <!--SR_WRITE("CORDIC_FREQ", $cordic_freq)--> - <!--</action>--> - <!--FIXME Calculate this properly--> - </arg> - <arg> - <name>input_rate</name> - <type>double</type> - <value>1.0</value> - <port>1</port> - <check>GE($input_rate, 0.0)</check> - <check_message>The input rate must be a positive value (in Hz).</check_message> - </arg> - <arg> - <name>output_rate</name> - <type>double</type> - <value>1.0</value> - <port>1</port> - <check>GE($output_rate, 0.0)</check> - <check_message>The output rate must be a positive value (in Hz).</check_message> - </arg> - <arg> - <name>fullscale</name> - <type>double</type> - <value>1.0</value> - <port>1</port> - <check>GE($fullscale, 0.0)</check> - </arg> - <arg> - <name>scalar_correction</name> - <type>double</type> - <value>1.0</value> - <port>1</port> - </arg> - </args> - <!--All the connections to the outside world are listed in 'ports':--> - <ports> - <sink> - <name>in0</name> - <type>sc16</type> - </sink> - <sink> - <name>in1</name> - <type>sc16</type> - </sink> - <source> - <name>out0</name> - <type>sc16</type> - </source> - <source> - <name>out1</name> - <type>sc16</type> - </source> - </ports> -</nocblock> - |