diff options
Diffstat (limited to 'fpga/usrp2/top/eth_test/eth_sim_top.v')
| -rw-r--r-- | fpga/usrp2/top/eth_test/eth_sim_top.v | 437 |
1 files changed, 0 insertions, 437 deletions
diff --git a/fpga/usrp2/top/eth_test/eth_sim_top.v b/fpga/usrp2/top/eth_test/eth_sim_top.v deleted file mode 100644 index 640a4e60f..000000000 --- a/fpga/usrp2/top/eth_test/eth_sim_top.v +++ /dev/null @@ -1,437 +0,0 @@ -////////////////////////////////////////////////////////////////////////////////// -// Module Name: u2_basic -////////////////////////////////////////////////////////////////////////////////// - -module eth_sim_top - (// Clocks - input dsp_clk, - input wb_clk, - output clock_ready, - input clk_to_mac, - input pps_in, - - // Misc, debug - output led1, - output led2, - output [31:0] debug, - output [1:0] debug_clk, - - // Expansion - input exp_pps_in, - output exp_pps_out, - - // GMII - // GMII-CTRL - input GMII_COL, - input GMII_CRS, - - // GMII-TX - output [7:0] GMII_TXD, - output GMII_TX_EN, - output GMII_TX_ER, - output GMII_GTX_CLK, - input GMII_TX_CLK, // 100mbps clk - - // GMII-RX - input [7:0] GMII_RXD, - input GMII_RX_CLK, - input GMII_RX_DV, - input GMII_RX_ER, - - // GMII-Management - inout MDIO, - output MDC, - input PHY_INTn, // open drain - input PHY_RESETn, - input PHY_CLK, // possibly use on-board osc - - // SERDES - output ser_enable, - output ser_prbsen, - output ser_loopen, - output ser_rx_en, - - output ser_tx_clk, - output [15:0] ser_t, - output ser_tklsb, - output ser_tkmsb, - - input ser_rx_clk, - input [15:0] ser_r, - input ser_rklsb, - input ser_rkmsb, - - // CPLD interface - output cpld_start, - output cpld_mode, - output cpld_done, - input cpld_din, - input cpld_clk, - input cpld_detached, - - // ADC - input [13:0] adc_a, - input adc_ovf_a, - output adc_oen_a, - output adc_pdn_a, - - input [13:0] adc_b, - input adc_ovf_b, - output adc_oen_b, - output adc_pdn_b, - - // DAC - output [15:0] dac_a, - output [15:0] dac_b, - - // I2C - input scl_pad_i, - output scl_pad_o, - output scl_pad_oen_o, - input sda_pad_i, - output sda_pad_o, - output sda_pad_oen_o, - - // Clock Gen Control - output [1:0] clk_en, - output [1:0] clk_sel, - input clk_func, // FIXME is an input to control the 9510 - input clk_status, - - // Generic SPI - output sclk, - output mosi, - input miso, - output sen_clk, - output sen_dac, - output sen_tx_db, - output sen_tx_adc, - output sen_tx_dac, - output sen_rx_db, - output sen_rx_adc, - output sen_rx_dac, - - // GPIO to DBoards - inout [15:0] io_tx, - inout [15:0] io_rx - ); - - wire [7:0] set_addr; - wire [31:0] set_data; - wire set_stb; - - wire ram_loader_done; - wire ram_loader_rst, wb_rst, dsp_rst; - - wire [31:0] ser_debug; - - ////////////////////////////////////////////////////////////////////////////////////////////////// - // Wishbone Single Master INTERCON - parameter dw = 32; // Data bus width - parameter aw = 16; // Address bus width, for byte addressibility, 16 = 64K byte memory space - parameter sw = 4; // Select width -- 32-bit data bus with 8-bit granularity. - - wire [dw-1:0] m0_dat_o, m1_dat_o, m0_dat_i, m1_dat_i; - wire [dw-1:0] s0_dat_o, s1_dat_o, s0_dat_i, s1_dat_i, s2_dat_o, s3_dat_o, s2_dat_i, s3_dat_i, - s4_dat_o, s5_dat_o, s4_dat_i, s5_dat_i, s6_dat_o, s7_dat_o, s6_dat_i, s7_dat_i; - wire [aw-1:0] m0_adr, m1_adr, s0_adr,s1_adr,s2_adr,s3_adr,s4_adr,s5_adr,s6_adr,s7_adr; - wire [sw-1:0] m0_sel, m1_sel, s0_sel, s1_sel, s2_sel, s3_sel, s4_sel, s5_sel, s6_sel, s7_sel; - wire m0_ack, m1_ack, s0_ack, s1_ack, s2_ack, s3_ack, s4_ack, s5_ack, s6_ack, s7_ack; - wire m0_stb, m1_stb, s0_stb, s1_stb, s2_stb, s3_stb, s4_stb, s5_stb, s6_stb, s7_stb; - wire m0_cyc, m1_cyc, s0_cyc, s1_cyc, s2_cyc, s3_cyc, s4_cyc, s5_cyc, s6_cyc, s7_cyc; - wire m0_err, m1_err, s0_err, s1_err, s2_err, s3_err, s4_err, s5_err, s6_err, s7_err; - wire m0_rty, m1_rty, s0_rty, s1_rty, s2_rty, s3_rty, s4_rty, s5_rty, s6_rty, s7_rty; - wire m0_we, m1_we, s0_we, s1_we, s2_we, s3_we, s4_we, s5_we, s6_we, s7_we; - - wb_1master #(.s0_addr_w(2),.s0_addr(2'b00),.s1_addr_w(2),.s1_addr(2'b01), - .s27_addr_w(4),.s2_addr(4'b1000),.s3_addr(4'b1001),.s4_addr(4'b1010), - .s5_addr(4'b1011),.s6_addr(4'b1100),.s7_addr(4'b1101), - .dw(dw),.aw(aw),.sw(sw)) wb_1master - (.clk_i(wb_clk),.rst_i(wb_rst), - - .m0_dat_o(m0_dat_o),.m0_ack_o(m0_ack),.m0_err_o(m0_err),.m0_rty_o(m0_rty),.m0_dat_i(m0_dat_i), - .m0_adr_i(m0_adr),.m0_sel_i(m0_sel),.m0_we_i(m0_we),.m0_cyc_i(m0_cyc),.m0_stb_i(m0_stb), - .s0_dat_o(s0_dat_o),.s0_adr_o(s0_adr),.s0_sel_o(s0_sel),.s0_we_o (s0_we),.s0_cyc_o(s0_cyc),.s0_stb_o(s0_stb), - .s0_dat_i(s0_dat_i),.s0_ack_i(s0_ack),.s0_err_i(s0_err),.s0_rty_i(s0_rty), - .s1_dat_o(s1_dat_o),.s1_adr_o(s1_adr),.s1_sel_o(s1_sel),.s1_we_o (s1_we),.s1_cyc_o(s1_cyc),.s1_stb_o(s1_stb), - .s1_dat_i(s1_dat_i),.s1_ack_i(s1_ack),.s1_err_i(s1_err),.s1_rty_i(s1_rty), - .s2_dat_o(s2_dat_o),.s2_adr_o(s2_adr),.s2_sel_o(s2_sel),.s2_we_o (s2_we),.s2_cyc_o(s2_cyc),.s2_stb_o(s2_stb), - .s2_dat_i(s2_dat_i),.s2_ack_i(s2_ack),.s2_err_i(s2_err),.s2_rty_i(s2_rty), - .s3_dat_o(s3_dat_o),.s3_adr_o(s3_adr),.s3_sel_o(s3_sel),.s3_we_o (s3_we),.s3_cyc_o(s3_cyc),.s3_stb_o(s3_stb), - .s3_dat_i(s3_dat_i),.s3_ack_i(s3_ack),.s3_err_i(s3_err),.s3_rty_i(s3_rty), - .s4_dat_o(s4_dat_o),.s4_adr_o(s4_adr),.s4_sel_o(s4_sel),.s4_we_o (s4_we),.s4_cyc_o(s4_cyc),.s4_stb_o(s4_stb), - .s4_dat_i(s4_dat_i),.s4_ack_i(s4_ack),.s4_err_i(s4_err),.s4_rty_i(s4_rty), - .s5_dat_o(s5_dat_o),.s5_adr_o(s5_adr),.s5_sel_o(s5_sel),.s5_we_o (s5_we),.s5_cyc_o(s5_cyc),.s5_stb_o(s5_stb), - .s5_dat_i(s5_dat_i),.s5_ack_i(s5_ack),.s5_err_i(s5_err),.s5_rty_i(s5_rty), - .s6_dat_o(s6_dat_o),.s6_adr_o(s6_adr),.s6_sel_o(s6_sel),.s6_we_o (s6_we),.s6_cyc_o(s6_cyc),.s6_stb_o(s6_stb), - .s6_dat_i(s6_dat_i),.s6_ack_i(s6_ack),.s6_err_i(s6_err),.s6_rty_i(s6_rty), - .s7_dat_o(s7_dat_o),.s7_adr_o(s7_adr),.s7_sel_o(s7_sel),.s7_we_o (s7_we),.s7_cyc_o(s7_cyc),.s7_stb_o(s7_stb), - .s7_dat_i(s7_dat_i),.s7_ack_i(s7_ack),.s7_err_i(s7_err),.s7_rty_i(s7_rty) - ); - - ////////////////////////////////////////////////////////////////////////////////////////// - // Reset Controller - system_control sysctrl (.wb_clk_i(wb_clk), - .ram_loader_rst_o(ram_loader_rst), - .wb_rst_o(wb_rst), - .ram_loader_done_i(ram_loader_done)); - - // /////////////////////////////////////////////////////////////////// - // RAM Loader - wire iram_wr_stb, iram_rd_stb, iram_wr_ack, iram_rd_ack, iram_ack, iram_wr_we; - wire [3:0] iram_wr_sel; - wire [aw-1:0] iram_wr_adr, iram_rd_adr; - wire [dw-1:0] iram_wr_dat, iram_rd_dat; - - wire bus_error, proc_int; - - assign iram_rd_ack = ram_loader_done ? iram_ack : 1'b0; - assign iram_wr_ack = ram_loader_done ? 1'b0 : iram_ack; - - ram_loader #(.AWIDTH(16)) - ram_loader (.clk_i(wb_clk),.rst_i(ram_loader_rst), - // CPLD Interface - .cfg_clk_i(cpld_clk), - .cfg_data_i(cpld_din), - .start_o(cpld_start), - .mode_o(cpld_mode), - .done_o(cpld_done), - .detached_i(cpld_detached), - // Wishbone Interface - .wb_dat_o(iram_wr_dat),.wb_adr_o(iram_wr_adr), - .wb_stb_o(iram_wr_stb),.wb_cyc_o(),.wb_sel_o(iram_wr_sel), - .wb_we_o(iram_wr_we),.wb_ack_i(iram_wr_ack), - .ram_loader_done_o(ram_loader_done)); - - // Processor - aeMB_core_BE #(.ISIZ(16),.DSIZ(16)) - aeMB (.sys_clk_i(wb_clk), .sys_rst_i(wb_rst), - // Instruction Wishbone bus to I-RAM - .iwb_stb_o(iram_rd_stb),.iwb_adr_o(iram_rd_adr), - .iwb_dat_i(iram_rd_dat),.iwb_ack_i(iram_rd_ack), - // Data Wishbone bus to system bus fabric - .dwb_we_o(m0_we),.dwb_stb_o(m0_stb),.dwb_dat_o(m0_dat_i),.dwb_adr_o(m0_adr), - .dwb_dat_i(m0_dat_o),.dwb_ack_i(m0_ack),.dwb_sel_o(m0_sel),.dwb_cyc_o(m0_cyc), - // Interrupts and exceptions - .sys_int_i(proc_int),.sys_exc_i(bus_error) ); - - assign bus_error = m0_err | m0_rty; - assign proc_int = 1'b0; - - // Dual Ported RAM -- D-Port is Slave #0 on main Wishbone - // I-port connects directly to processor and ram loader - - ram_wb_harvard #(.AWIDTH(14)) - ID_ram (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst), - - .iwb_adr_i(ram_loader_done ? iram_rd_adr : iram_wr_adr),.iwb_dat_i(iram_wr_dat),.iwb_dat_o(iram_rd_dat), - .iwb_we_i(iram_wr_we),.iwb_ack_o(iram_ack),.iwb_stb_i(ram_loader_done ? iram_rd_stb : iram_wr_stb), - .iwb_sel_i(ram_loader_done ? 4'b1111 : iram_wr_sel), - - .dwb_adr_i(s0_adr),.dwb_dat_i(s0_dat_o),.dwb_dat_o(s0_dat_i), - .dwb_we_i(s0_we),.dwb_ack_o(s0_ack),.dwb_stb_i(s0_stb),.dwb_sel_i(s0_sel)); - - assign s0_err = 1'b0; - assign s0_rty = 1'b0; - - // Buffer Pool, slave #1 - wire rd0_read, rd0_ready, rd0_done, rd0_empty; - wire rd1_read, rd1_ready, rd1_done, rd1_empty; - wire rd2_read, rd2_ready, rd2_done, rd2_empty; - wire rd3_read, rd3_ready, rd3_done, rd3_empty; - wire [31:0] rd0_dat, rd1_dat, rd2_dat, rd3_dat; - - wire wr0_write, wr0_done, wr0_ready, wr0_full; - wire wr1_write, wr1_done, wr1_ready, wr1_full; - wire wr2_write, wr2_done, wr2_ready, wr2_full; - wire wr3_write, wr3_done, wr3_ready, wr3_full; - wire [31:0] wr0_dat, wr1_dat, wr2_dat, wr3_dat; - -/* - buffer_pool buffer_pool - (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst), - .wb_we_i(s1_we),.wb_stb_i(s1_stb),.wb_adr_i(s1_adr),.wb_dat_i(s1_dat_o), - .wb_dat_o(s1_dat_i),.wb_ack_o(s1_ack),.wb_err_o(s1_err),.wb_rty_o(s1_rty), - - .stream_clk(dsp_clk),.stream_rst(dsp_rst), - // Write Interfaces - .wr0_dat_i(),.wr0_write_i(),.wr0_done_i(),.wr0_ready_o(),.wr0_full_o(), - .wr1_dat_i(),.wr1_write_i(),.wr1_done_i(),.wr1_ready_o(),.wr1_full_o(), - .wr2_dat_i(),.wr2_write_i(),.wr2_done_i(),.wr2_ready_o(),.wr2_full_o(), - .wr3_dat_i(),.wr3_write_i(),.wr3_done_i(),.wr3_ready_o(),.wr3_full_o(), - // Read Interfaces - .rd0_dat_o(rd0_dat),.rd0_read_i(rd0_read),.rd0_done_i(),.rd0_ready_o(rd0_ready),.rd0_empty_o(rd0_empty), - .rd1_dat_o(rd1_dat),.rd1_read_i(rd1_read),.rd1_done_i(),.rd1_ready_o(rd1_ready),.rd1_empty_o(rd1_empty), - .rd2_dat_o(rd2_dat),.rd2_read_i(rd2_read),.rd2_done_i(),.rd2_ready_o(rd2_ready),.rd2_empty_o(rd2_empty), - .rd3_dat_o(rd3_dat),.rd3_read_i(rd3_read),.rd3_done_i(),.rd3_ready_o(rd3_ready),.rd3_empty_o(rd3_empty) - ); -*/ - // SPI -- Slave #2 - spi_top shared_spi - (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.wb_adr_i(s2_adr),.wb_dat_i(s2_dat_o),.wb_dat_o(s2_dat_i), - .wb_sel_i(s2_sel),.wb_we_i(s2_we),.wb_stb_i(s2_stb),.wb_cyc_i(s2_cyc),.wb_ack_o(s2_ack), - - .wb_err_o(s2_err),.wb_int_o(s2_int), - .ss_pad_o({sen_tx_db,sen_tx_adc,sen_tx_dac,sen_rx_db,sen_rx_adc,sen_rx_dac,sen_dac,sen_clk}), - .sclk_pad_o(sclk),.mosi_pad_o(mosi),.miso_pad_i(miso) ); - - assign s2_rty = 1'b0; - - // I2C -- Slave #3 - i2c_master_top #(.ARST_LVL(1)) - i2c (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.arst_i(1'b0), - .wb_adr_i(s3_adr),.wb_dat_i(s3_dat_o),.wb_dat_o(s3_dat_i), - .wb_we_i(s3_we),.wb_stb_i(s3_stb),.wb_cyc_i(s3_cyc), - .wb_ack_o(s3_ack),.wb_inta_o(st_int), - .scl_pad_i(scl_pad_i),.scl_pad_o(scl_pad_o),.scl_padoen_o(scl_pad_oen_o), - .sda_pad_i(sda_pad_i),.sda_pad_o(sda_pad_o),.sda_padoen_o(sda_pad_oen_o) ); - - assign s3_err = 1'b0; - assign s3_rty = 1'b0; - - // GPIOs -- Slave #4 - wire s4_ack_a, s4_ack_b, s4_ack_c, s4_ack_d; - assign s4_ack = s4_ack_a | s4_ack_b | s4_ack_c | s4_ack_d; - - simple_gpio gpio_a(.clk_i(wb_clk),.rst_i(~wb_rst), - .cyc_i(s4_cyc),.stb_i(s4_stb&s4_sel[0]),.adr_i(s4_adr[2]),.we_i(s4_we), - .dat_i(s4_dat_o[7:0]),.dat_o(s4_dat_i[7:0]),.ack_o(s4_ack_a), - .gpio(/* io_tx[7:0]*/) ); - - simple_gpio gpio_b(.clk_i(wb_clk),.rst_i(~wb_rst), - .cyc_i(s4_cyc),.stb_i(s4_stb&s4_sel[1]),.adr_i(s4_adr[2]),.we_i(s4_we), - .dat_i(s4_dat_o[15:8]),.dat_o(s4_dat_i[15:8]),.ack_o(s4_ack_b), - .gpio(/* io_tx[15:8] */) ); - - simple_gpio gpio_c(.clk_i(wb_clk),.rst_i(~wb_rst), - .cyc_i(s4_cyc),.stb_i(s4_stb&s4_sel[2]),.adr_i(s4_adr[2]),.we_i(s4_we), - .dat_i(s4_dat_o[23:16]),.dat_o(s4_dat_i[23:16]),.ack_o(s4_ack_c), - .gpio(/* io_rx[7:0] */) ); - - simple_gpio gpio_d(.clk_i(wb_clk),.rst_i(~wb_rst), - .cyc_i(s4_cyc),.stb_i(s4_stb&s4_sel[3]),.adr_i(s4_adr[2]),.we_i(s4_we), - .dat_i(s4_dat_o[31:24]),.dat_o(s4_dat_i[31:24]),.ack_o(s4_ack_d), - .gpio(/* io_rx[15:8]*/) ); - - assign s4_err = 1'b0; - assign s4_rty = 1'b0; - - // Output control lines, SLAVE #5 - wire [7:0] clock_outs, serdes_outs, adc_outs, misc_outs; - assign {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0]; - assign {ser_enable, ser_prbsen, ser_loopen, ser_rx_en} = serdes_outs[3:0]; - assign { adc_oen_a, adc_pdn_a, adc_oen_b, adc_pdn_b } = adc_outs[3:0]; - assign {led2, led1} = misc_outs[1:0]; - - wb_output_pins32 control_lines - (.wb_rst_i(wb_rst),.wb_clk_i(wb_clk),.wb_dat_i(s5_dat_o),.wb_dat_o(s5_dat_i), - .wb_we_i(s5_we),.wb_sel_i(s5_sel),.wb_stb_i(s5_stb),.wb_ack_o(s5_ack),.wb_cyc_i(s5_cyc), - .port_output( {clock_outs,serdes_outs,adc_outs,misc_outs} ) ); - - assign s5_err = 1'b0; - assign s5_rty = 1'b0; - - // Ethernet slave, #6 - eth_wrapper eth_wrapper - (.Reset(wb_rst),.Clk_125M(),.Clk_user(stream_clk),.Clk_reg(wb_clk),.Speed(), - .Gtx_clk(GMII_GTX_CLK),.Rx_clk(GMII_RX_CLK),.Tx_clk(GMII_TX_CLK),//used only in MII mode - .Tx_er(GMII_TX_ER),.Tx_en(GMII_TX_EN),.Txd(GMII_TXD),.Rx_er(GMII_RX_ER), - .Rx_dv(GMII_RX_DV),.Rxd(GMII_RXD),.Crs(GMII_CRS),.Col(GMII_COL), - .Mdio(MDIO),.Mdc(MDC), - // FIFO Interfaces - .wr_dat_o(),.wr_write_o(),.wr_done_o(),.wr_ready_i(),.wr_full_i(), - .rd_dat_i(),.rd_read_o(),.rd_done_o(),.rd_ready_i(),.rd_empty_i(), - // Wishbone - .wb_dat_i(s6_dat_o),.wb_dat_o(s6_dat_i),.wb_adr_i(s6_adr),.wb_stb_i(s6_stb),.wb_we_i(s6_we),.wb_ack_o(s6_ack) - ); - - assign s6_err = 1'b0; - assign s6_rty = 1'b0; - - // Settings Bus -- Slave #7 - settings_bus settings_bus - (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s7_adr),.wb_dat_i(s7_dat_o), - .wb_stb_i(s7_stb),.wb_we_i(s7_we),.wb_ack_o(s7_ack), - .sys_clk(dsp_clk),.strobe(set_stb),.addr(set_addr),.data(set_data)); - - assign s7_err = 1'b0; - assign s7_rty = 1'b0; - assign s7_dat_i = 32'd0; - - /////////////////////////////////////////////////////////////////////////// - // DSP - reg [13:0] adc_a_reg1, adc_b_reg1, adc_a_reg2, adc_b_reg2; - reg adc_ovf_a_reg1, adc_ovf_a_reg2, adc_ovf_b_reg1, adc_ovf_b_reg2; - - always @(posedge dsp_clk) - begin - adc_a_reg1 <= adc_a; - adc_a_reg2 <= adc_a_reg1; - adc_b_reg1 <= adc_b; - adc_b_reg2 <= adc_b_reg1; - adc_ovf_a_reg1 <= adc_ovf_a; - adc_ovf_a_reg2 <= adc_ovf_a_reg1; - adc_ovf_b_reg1 <= adc_ovf_b; - adc_ovf_b_reg2 <= adc_ovf_b_reg1; - end // always @ (posedge dsp_clk) - - dsp_core_rx dsp_core_rx - (.clk(dsp_clk),.rst(dsp_rst), - .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data), - .adc_a(adc_a),.adc_ovf_a(adc_ovf_a),.adc_b(adc_b),.adc_ovf_b(adc_ovf_b), - .rx_dat_o(wr1_dat),.rx_write_o(wr1_write),.rx_done_o(wr1_done), - .rx_ready_i(wr1_ready),.rx_full_i(wr1_full), - .overrun() ); - - dsp_core_tx dsp_core_tx - (.clk(dsp_clk),.rst(dsp_rst), - .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data), - .dac_a(dac_a),.dac_b(dac_b), - .tx_dat_i(rd1_dat),.tx_read_o(rd1_read),.tx_done_o(rd1_done), - .tx_ready_i(rd1_ready),.tx_empty_i(rd1_empty), - .underrun() ); - - assign dsp_rst = wb_rst; - - ///////////////////////////////////////////////////////////////////////////////////// - // SERDES - serdes_tx serdes_tx - (.clk(dsp_clk),.rst(dsp_rst), - .ser_tx_clk(ser_tx_clk),.ser_t(ser_t),.ser_tklsb(ser_tklsb),.ser_tkmsb(ser_tkmsb), - .fifo_data_i(rd0_dat),.fifo_read_o(rd0_read),.fifo_done_o(rd0_done), - .fifo_ready_i(rd0_ready),.fifo_empty_i(rd0_empty) - ); - - serdes_rx serdes_rx - (.clk(dsp_clk),.rst(dsp_rst), - .ser_rx_clk(ser_rx_clk),.ser_r(ser_r),.ser_rklsb(ser_rklsb),.ser_rkmsb(ser_rkmsb), - .fifo_data_o(wr0_dat),.fifo_wr_o(wr0_write),.fifo_ready_i(wr0_ready),.fifo_done_i(wr0_done) - ); - - // Debug Pins - wire [31:0] debug1={{1'b0,ram_loader_done,clock_ready,dsp_clk,wb_clk,ram_loader_rst,wb_rst,dsp_rst}, - {1'b0,cpld_start,cpld_mode,cpld_done,1'b0,cpld_din,cpld_clk,cpld_detached}, - {8'hAF}, - {2'b0, clk_status, sen_dac, sen_clk, sclk, mosi, miso}}; - - wire [31:0] debug_wb={{iram_wr_we,ram_loader_done,clock_ready,iram_wr_ack,iram_wr_stb,ram_loader_rst,wb_rst,dsp_rst}, - {iram_rd_adr[15:8]}, - {iram_rd_adr[7:0]}, - {serdes_outs}}; - - assign io_rx = ser_debug[31:16]; - assign io_tx = ser_debug[15:0]; - - assign debug = debug_wb; - - assign debug_clk[0] = wb_clk; - assign debug_clk[1] = dsp_clk; - -endmodule // eth_test - - -// Local Variables: -// verilog-library-directories:("." "subdir" "subdir2") -// verilog-library-files:("/home/matt/u2f/opencores/wb_conbus/rtl/verilog/wb_conbus_top.v") -// verilog-library-extensions:(".v" ".h") -// End: |