diff options
Diffstat (limited to 'fpga/usrp2/gpmc/fifo_to_gpmc.v')
| -rw-r--r-- | fpga/usrp2/gpmc/fifo_to_gpmc.v | 159 |
1 files changed, 159 insertions, 0 deletions
diff --git a/fpga/usrp2/gpmc/fifo_to_gpmc.v b/fpga/usrp2/gpmc/fifo_to_gpmc.v new file mode 100644 index 000000000..42c71d2d6 --- /dev/null +++ b/fpga/usrp2/gpmc/fifo_to_gpmc.v @@ -0,0 +1,159 @@ +// +// Copyright 2011 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +//////////////////////////////////////////////////////////////////////// +// FIFO to GPMC +// +// Reads frames from FIFO interface and writes them into BRAM pages. +// The GPMC is asynchronously alerted when a BRAM page has been filled. +// +// EM_CLK: +// A GPMC read transaction consists of two EM_CLK cycles (idle low). +// +// EM_OE: +// Output enable is actually the combination of ~NOE & ~NCS. +// The output enable is only active for the second rising edge, +// to ensure one edge per transaction to transition on. +// +// EM_D: +// The BRAM performs a read on the first rising edge into EM_D. +// Then, data will then be read on the next rising edge by GPMC. +// +// EM_A: +// On the first rising edge of EM_CLK, the address is held. +// On the second rising edge, the address is set for the next transaction. +//////////////////////////////////////////////////////////////////////// + +module fifo_to_gpmc + #(parameter PTR_WIDTH = 2, parameter ADDR_WIDTH = 10) + (input clk, input reset, input clear, input arst, + input [17:0] data_i, input src_rdy_i, output dst_rdy_o, + output [15:0] EM_D, input [ADDR_WIDTH:1] EM_A, input EM_CLK, input EM_OE, + output reg data_available); + + //states for the GPMC side of things + wire [17:0] data_o; + reg gpmc_state; + reg [ADDR_WIDTH:1] addr; + reg [PTR_WIDTH:0] gpmc_ptr, next_gpmc_ptr; + localparam GPMC_STATE_START = 0; + localparam GPMC_STATE_EMPTY = 1; + + //states for the FIFO side of things + reg fifo_state; + reg [ADDR_WIDTH-1:0] counter; + reg [PTR_WIDTH:0] fifo_ptr; + localparam FIFO_STATE_CLAIM = 0; + localparam FIFO_STATE_FILL = 1; + + //------------------------------------------------------------------ + // State machine to control the data from GPMC to BRAM + //------------------------------------------------------------------ + always @(posedge EM_CLK or posedge arst) begin + if (arst) begin + gpmc_state <= GPMC_STATE_START; + gpmc_ptr <= 0; + next_gpmc_ptr <= 0; + addr <= 0; + end + else if (EM_OE) begin + addr <= EM_A + 1; + case(gpmc_state) + + GPMC_STATE_START: begin + if (EM_A == 0) begin + gpmc_state <= GPMC_STATE_EMPTY; + next_gpmc_ptr <= gpmc_ptr + 1; + end + end + + GPMC_STATE_EMPTY: begin + if (EM_A == 10'h3ff) begin + gpmc_state <= GPMC_STATE_START; + gpmc_ptr <= next_gpmc_ptr; + end + end + + endcase //gpmc_state + end //EM_WE + end //always + + //------------------------------------------------------------------ + // High when the gpmc pointer has not caught up to the fifo pointer. + //------------------------------------------------------------------ + wire [PTR_WIDTH:0] safe_gpmc_ptr; + cross_clock_reader #(.WIDTH(PTR_WIDTH+1)) read_gpmc_ptr + (.clk(clk), .rst(reset | clear), .in(gpmc_ptr), .out(safe_gpmc_ptr)); + + wire bram_available_to_fill = (fifo_ptr ^ (1 << PTR_WIDTH)) != safe_gpmc_ptr; + + //------------------------------------------------------------------ + // Glich free generation of data available signal: + // Data is available when the pointers dont match. + //------------------------------------------------------------------ + wire [PTR_WIDTH:0] safe_next_gpmc_ptr; + cross_clock_reader #(.WIDTH(PTR_WIDTH+1)) read_next_gpmc_ptr + (.clk(clk), .rst(reset | clear), .in(next_gpmc_ptr), .out(safe_next_gpmc_ptr)); + + always @(posedge clk) + if (reset | clear) data_available <= 0; + else data_available <= safe_next_gpmc_ptr != fifo_ptr; + + //------------------------------------------------------------------ + // State machine to control the data from BRAM to FIFO + //------------------------------------------------------------------ + always @(posedge clk) begin + if (reset | clear) begin + fifo_state <= FIFO_STATE_CLAIM; + fifo_ptr <= 0; + counter <= 0; + end + else begin + case(fifo_state) + + FIFO_STATE_CLAIM: begin + if (bram_available_to_fill) fifo_state <= FIFO_STATE_FILL; + counter <= 0; + end + + FIFO_STATE_FILL: begin + if (src_rdy_i && dst_rdy_o && data_i[17]) begin + fifo_state <= FIFO_STATE_CLAIM; + fifo_ptr <= fifo_ptr + 1; + end + if (src_rdy_i && dst_rdy_o) begin + counter <= counter + 1; + end + end + + endcase //fifo_state + end + end //always + + assign dst_rdy_o = fifo_state == FIFO_STATE_FILL; + + //assign data from bram output + assign EM_D = data_o[15:0]; + + //instantiate dual ported bram for async read + write + ram_2port #(.DWIDTH(18),.AWIDTH(PTR_WIDTH + ADDR_WIDTH)) async_fifo_bram + (.clka(clk),.ena(1'b1),.wea(src_rdy_i && dst_rdy_o), + .addra({fifo_ptr[PTR_WIDTH-1:0], counter}),.dia(data_i),.doa(), + .clkb(EM_CLK),.enb(1'b1),.web(1'b0), + .addrb({gpmc_ptr[PTR_WIDTH-1:0], addr}),.dib(18'h3ffff),.dob(data_o)); + +endmodule // fifo_to_gpmc |