diff options
Diffstat (limited to 'firmware/fx2/include/fpga_regs_standard.v')
| -rw-r--r-- | firmware/fx2/include/fpga_regs_standard.v | 256 |
1 files changed, 256 insertions, 0 deletions
diff --git a/firmware/fx2/include/fpga_regs_standard.v b/firmware/fx2/include/fpga_regs_standard.v new file mode 100644 index 000000000..d09aa6116 --- /dev/null +++ b/firmware/fx2/include/fpga_regs_standard.v @@ -0,0 +1,256 @@ +// +// This file is machine generated from ./fpga_regs_standard.h +// Do not edit by hand; your edits will be overwritten. +// + +// Register numbers 0 to 31 are reserved for use in fpga_regs_common.h. +// Registers 64 to 79 are available for custom FPGA builds. + + +// DDC / DUC + +`define FR_INTERP_RATE 7'd32 // [1,1024] +`define FR_DECIM_RATE 7'd33 // [1,256] + +// DDC center freq + +`define FR_RX_FREQ_0 7'd34 +`define FR_RX_FREQ_1 7'd35 +`define FR_RX_FREQ_2 7'd36 +`define FR_RX_FREQ_3 7'd37 + +// See below for DDC Starting Phase + +// ------------------------------------------------------------------------ +// configure FPGA Rx mux +// +// 3 2 1 +// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 +// +-----------------------+-------+-------+-------+-------+-+-----+ +// | must be zero | Q3| I3| Q2| I2| Q1| I1| Q0| I0|Z| NCH | +// +-----------------------+-------+-------+-------+-------+-+-----+ +// +// There are a maximum of 4 digital downconverters in the the FPGA. +// Each DDC has two 16-bit inputs, I and Q, and two 16-bit outputs, I & Q. +// +// DDC I inputs are specified by the two bit fields I3, I2, I1 & I0 +// +// 0 = DDC input is from ADC 0 +// 1 = DDC input is from ADC 1 +// 2 = DDC input is from ADC 2 +// 3 = DDC input is from ADC 3 +// +// If Z == 1, all DDC Q inputs are set to zero +// If Z == 0, DDC Q inputs are specified by the two bit fields Q3, Q2, Q1 & Q0 +// +// NCH specifies the number of complex channels that are sent across +// the USB. The legal values are 1, 2 or 4, corresponding to 2, 4 or +// 8 16-bit values. + +`define FR_RX_MUX 7'd38 + +// ------------------------------------------------------------------------ +// configure FPGA Tx Mux. +// +// 3 2 1 +// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 +// +-----------------------+-------+-------+-------+-------+-+-----+ +// | | DAC3 | DAC2 | DAC1 | DAC0 |0| NCH | +// +-----------------------------------------------+-------+-+-----+ +// +// NCH specifies the number of complex channels that are sent across +// the USB. The legal values are 1 or 2, corresponding to 2 or 4 +// 16-bit values. +// +// There are two interpolators with complex inputs and outputs. +// There are four DACs. (We use the DUC in each AD9862.) +// +// Each 4-bit DACx field specifies the source for the DAC and +// whether or not that DAC is enabled. Each subfield is coded +// like this: +// +// 3 2 1 0 +// +-+-----+ +// |E| N | +// +-+-----+ +// +// Where E is set if the DAC is enabled, and N specifies which +// interpolator output is connected to this DAC. +// +// N which interp output +// --- ------------------- +// 0 chan 0 I +// 1 chan 0 Q +// 2 chan 1 I +// 3 chan 1 Q + +`define FR_TX_MUX 7'd39 + +// ------------------------------------------------------------------------ +// REFCLK control +// +// Control whether a reference clock is sent to the daughterboards, +// and what frequency. The refclk is sent on d'board i/o pin 0. +// +// 3 2 1 +// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 +// +-----------------------------------------------+-+------------+ +// | Reserved (Must be zero) |E| DIVISOR | +// +-----------------------------------------------+-+------------+ + +// +// Bit 7 -- 1 turns on refclk, 0 allows IO use +// Bits 6:0 Divider value + +`define FR_TX_A_REFCLK 7'd40 +`define FR_RX_A_REFCLK 7'd41 +`define FR_TX_B_REFCLK 7'd42 +`define FR_RX_B_REFCLK 7'd43 + + +// ------------------------------------------------------------------------ +// DDC Starting Phase + +`define FR_RX_PHASE_0 7'd44 +`define FR_RX_PHASE_1 7'd45 +`define FR_RX_PHASE_2 7'd46 +`define FR_RX_PHASE_3 7'd47 + +// ------------------------------------------------------------------------ +// Tx data format control register +// +// 3 2 1 +// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 +// +-------------------------------------------------------+-------+ +// | Reserved (Must be zero) | FMT | +// +-------------------------------------------------------+-------+ +// +// FMT values: + +`define FR_TX_FORMAT 7'd48 + +// ------------------------------------------------------------------------ +// Rx data format control register +// +// 3 2 1 +// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 +// +-----------------------------------------+-+-+---------+-------+ +// | Reserved (Must be zero) |B|Q| WIDTH | SHIFT | +// +-----------------------------------------+-+-+---------+-------+ +// +// FMT values: + +`define FR_RX_FORMAT 7'd49 + + +// The valid combinations currently are: +// +// B Q WIDTH SHIFT +// 0 1 16 0 +// 0 1 8 8 + + +// Possible future values of WIDTH = {4, 2, 1} +// 12 takes a bit more work, since we need to know packet alignment. + +// ------------------------------------------------------------------------ +// FIXME register numbers 50 to 63 are available + +// ------------------------------------------------------------------------ +// Registers 64 to 95 are reserved for user custom FPGA builds. +// The standard USRP software will not touch these. + +`define FR_USER_0 7'd64 +`define FR_USER_1 7'd65 +`define FR_USER_2 7'd66 +`define FR_USER_3 7'd67 +`define FR_USER_4 7'd68 +`define FR_USER_5 7'd69 +`define FR_USER_6 7'd70 +`define FR_USER_7 7'd71 +`define FR_USER_8 7'd72 +`define FR_USER_9 7'd73 +`define FR_USER_10 7'd74 +`define FR_USER_11 7'd75 +`define FR_USER_12 7'd76 +`define FR_USER_13 7'd77 +`define FR_USER_14 7'd78 +`define FR_USER_15 7'd79 +`define FR_USER_16 7'd80 +`define FR_USER_17 7'd81 +`define FR_USER_18 7'd82 +`define FR_USER_19 7'd83 +`define FR_USER_20 7'd84 +`define FR_USER_21 7'd85 +`define FR_USER_22 7'd86 +`define FR_USER_23 7'd87 +`define FR_USER_24 7'd88 +`define FR_USER_25 7'd89 +`define FR_USER_26 7'd90 +`define FR_USER_27 7'd91 +`define FR_USER_28 7'd92 +`define FR_USER_29 7'd93 +`define FR_USER_30 7'd94 +`define FR_USER_31 7'd95 + +//Registers needed for multi usrp master/slave configuration +// +//Rx Master/slave control register (FR_RX_MASTER_SLAVE = FR_USER_0) +// +`define FR_RX_MASTER_SLAVE 7'd64 +`define bitnoFR_RX_SYNC 0 +`define bitnoFR_RX_SYNC_MASTER 1 +`define bitnoFR_RX_SYNC_SLAVE 2 + + +//Caution The master settings will output values on the io lines. +//They inheritely enable these lines as output. If you have a daughtercard which uses these lines also as output then you will burn your usrp and daughtercard. +//If you set the slave bits then your usrp won't do anything if you don't connect a master. +// Rx Master/slave control register +// +// The way this is supposed to be used is connecting a (short) 16pin flatcable from an rx daughterboard in RXA master io_rx[8..15] to slave io_rx[8..15] on RXA of slave usrp +// This can be done with basic_rx boards or dbsrx boards +//dbsrx: connect master-J25 to slave-J25 +//basic rx: connect J25 to slave-J25 +//CAUTION: pay attention to the lineup of your connector. +//The red line (pin1) should be at the same side of the daughterboards on master and slave. +//If you turnaround the cable on one end you will burn your usrp. + +//You cannot use a 16pin flatcable if you are using FLEX400 or FLEX2400 daughterboards, since these use a lot of the io pins. +//You can still link them but you must use only a 2pin or 1pin cable +//You can also use a 2-wire link. put a 2pin header on io[15],gnd of the master RXA daughterboard and connect it to io15,gnd of the slave RXA db. +//You can use a cable like the ones found with the leds on the mainbord of a PC. +//Make sure you don't twist the cable, otherwise you connect the sync output to ground. +//To be save you could also just use a single wire from master io[15] to slave io[15], but this is not optimal for signal integrity. + + +// Since rx_io[0] can normally be used as a refclk and is not exported on all daughterboards this line +// still has the refclk function if you use the master/slave setup (it is not touched by the master/slave settings). +// The master/slave circuitry will only use io pin 15 and does not touch any of the other io pins. +`define bitnoFR_RX_SYNC_INPUT_IOPIN 15 +`define bmFR_RX_SYNC_INPUT_IOPIN (1<<bitnoFR_RX_SYNC_INPUT_IOPIN) +//TODO the output pin is still hardcoded in the verilog code, make it listen to the following define +`define bitnoFR_RX_SYNC_OUTPUT_IOPIN 15 +`define bmFR_RX_SYNC_OUTPUT_IOPIN (1<<bitnoFR_RX_SYNC_OUTPUT_IOPIN) +// ======================================================================= +// READBACK Registers +// ======================================================================= + +`define FR_RB_IO_RX_A_IO_TX_A 7'd1 // read back a-side i/o pins +`define FR_RB_IO_RX_B_IO_TX_B 7'd2 // read back b-side i/o pins + +// ------------------------------------------------------------------------ +// FPGA Capability register +// +// 3 2 1 +// 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 +// +-----------------------------------------------+-+-----+-+-----+ +// | Reserved (Must be zero) |T|NDUC |R|NDDC | +// +-----------------------------------------------+-+-----+-+-----+ +// +// Bottom 4-bits are Rx capabilities +// Next 4-bits are Tx capabilities + +`define FR_RB_CAPS 7'd3 + + |