diff options
| -rw-r--r-- | host/docs/usrp_e3xx.dox | 2 | ||||
| -rw-r--r-- | host/docs/usrp_n3xx.dox | 12 | ||||
| -rw-r--r-- | mpm/systemd/network/int0.network | 2 |
3 files changed, 8 insertions, 8 deletions
diff --git a/host/docs/usrp_e3xx.dox b/host/docs/usrp_e3xx.dox index 500977a19..1b0cb4249 100644 --- a/host/docs/usrp_e3xx.dox +++ b/host/docs/usrp_e3xx.dox @@ -459,7 +459,7 @@ The factory settings are as follows: Address=192.168.10.2/24 [Link] - MTUBytes=8000 + MTUBytes=9000 Note: Care needs to be taken when editing these files on the device, since vi / vim sometimes generates undo files (e.g. /etc/systemd/networkd/sfp0.network~), diff --git a/host/docs/usrp_n3xx.dox b/host/docs/usrp_n3xx.dox index ee9884f49..82bffc105 100644 --- a/host/docs/usrp_n3xx.dox +++ b/host/docs/usrp_n3xx.dox @@ -297,7 +297,7 @@ that will request a network address from your DHCP server (if available on your network). The SFP+ (sfp0, sfp1) ports are configured with static addresses 192.168.10.2/24 -and 192.168.20.2/24, respectively. Their default MTU value is 8000. These +and 192.168.20.2/24, respectively. Their default MTU value is 9000. These settings are independent of the image type (HG vs. XG), i.e., the defaults are the same for 1 GigE and 10 GigE (unlike the X310!). @@ -328,7 +328,7 @@ The factory settings are as follows: Address=192.168.10.2/24 [Link] - MTUBytes=8000 + MTUBytes=9000 sfp1 (static): @@ -339,7 +339,7 @@ The factory settings are as follows: Address=192.168.20.2/24 [Link] - MTUBytes=8000 + MTUBytes=9000 Additional notes on networking: @@ -803,10 +803,10 @@ incorrect values. Often, the host computer MTU is set smaller than the device MTU, but the MTU discovery will detect a larger MTU than the host computer MTU in this error case. -The default MTU for the N3x0 series is 8000. The simplest solution is often to -set the host computer MTU to 8000 as well: +The default MTU for the N3x0 series is 9000. The simplest solution is often to +set the host computer MTU to 9000 as well: - $ [sudo] ifconfig eth0 mtu 8000 # Replace eth0 with the device you're using + $ [sudo] ifconfig eth0 mtu 9000 # Replace eth0 with the device you're using Of course, you can also reduce the MTU on the device to match your host computer, see Section \ref n3xx_getting_started_connectivity. diff --git a/mpm/systemd/network/int0.network b/mpm/systemd/network/int0.network index 1b939a2f9..67a04c322 100644 --- a/mpm/systemd/network/int0.network +++ b/mpm/systemd/network/int0.network @@ -6,4 +6,4 @@ Address=169.254.0.1/24 IPForward=ipv4 [Link] -MTUBytes=8000 +MTUBytes=9000 |