dsp rework: implemented dsp changes for other top levels

added user registers into each toplevel (not used yet)

2 files changed, 65 insertions, 1 deletions

diff --git a/usrp2/control_lib/Makefile.srcs b/usrp2/control_lib/Makefile.srcs
index 567feacde..6ee7ea262 100644
--- a/usrp2/control_lib/Makefile.srcs
+++ b/usrp2/control_lib/Makefile.srcs
@@ -1,5 +1,5 @@
 #
-# Copyright 2010 Ettus Research LLC
+# Copyright 2010-2012 Ettus Research LLC
 #
 
 ##################################################
@@ -54,4 +54,5 @@ settings_bus_16LE.v \
 atr_controller16.v \
 fifo_to_wb.v \
 gpio_atr.v \
+user_settings.v \
 ))
diff --git a/usrp2/control_lib/user_settings.v b/usrp2/control_lib/user_settings.v
new file mode 100644
index 000000000..96ee22427
--- /dev/null
+++ b/usrp2/control_lib/user_settings.v
@@ -0,0 +1,63 @@
+//
+// Copyright 2011 Corgan Enterprises LLC
+//
+// This program is free software: you can redistribute it and/or modify
+// it under the terms of the GNU General Public License as published by
+// the Free Software Foundation, either version 3 of the License, or
+// (at your option) any later version.
+//
+// This program is distributed in the hope that it will be useful,
+// but WITHOUT ANY WARRANTY; without even the implied warranty of
+// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// GNU General Public License for more details.
+//
+// You should have received a copy of the GNU General Public License
+// along with this program.  If not, see <http://www.gnu.org/licenses/>.
+//
+
+// User settings bus
+//
+// Provides 8-bit address, 32-bit data write only bus for user settings, consumes to addresses in
+// normal settings bus.
+//
+// Write user address to BASE
+// Write user data to BASE+1
+//
+// The user_set_stb will strobe after data write, must write new address even if same as previous one.
+
+module user_settings
+  #(parameter BASE=0)
+  (input clk,
+   input rst,
+
+   input         set_stb,
+   input [7:0]   set_addr,
+   input [31:0]  set_data,
+
+   output        set_stb_user,
+   output [7:0]  set_addr_user,
+   output [31:0] set_data_user
+   );
+
+   wire 	 addr_changed, data_changed;
+   reg 		 stb_int;
+   
+   setting_reg #(.my_addr(BASE+0),.width(8)) sr_0
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(set_addr_user),.changed(addr_changed) );
+   
+   setting_reg #(.my_addr(BASE+1)) sr_1
+     (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+      .in(set_data),.out(set_data_user),.changed(data_changed) );
+   
+   always @(posedge clk)
+     if (rst|set_stb_user)
+       stb_int <= 0;
+     else
+       if (addr_changed)
+         stb_int <= 1;
+   
+   assign set_stb_user = stb_int & data_changed;
+   
+endmodule // user_settings
+