moved usrp1 and usrp2 fpga dirs into fpga subdirectory

1 files changed, 292 insertions, 0 deletions

diff --git a/fpga/usrp2/serdes/serdes_rx.v b/fpga/usrp2/serdes/serdes_rx.v
new file mode 100644
index 000000000..afefccaa1
--- /dev/null
+++ b/fpga/usrp2/serdes/serdes_rx.v
@@ -0,0 +1,292 @@
+
+// SERDES Interface
+
+// LS-Byte is sent first, MS-Byte is second
+// Invalid K Codes
+//  K0.0  000-00000  Error detected
+//  K31.7 111-11111  Loss of input signal
+
+// Valid K Codes
+//  K28.0 000-11100
+//  K28.1 001-11100  Alternate COMMA?
+//  K28.2 010-11100
+//  K28.3 011-11100
+//  K28.4 100-11100
+//  K28.5 101-11100  Standard COMMA?
+//  K28.6 110-11100
+//  K28.7 111-11100  Bad COMMA?
+//  K23.7 111-10111
+//  K27.7 111-11011
+//  K29.7 111-11101
+//  K30.7 111-11110
+
+module serdes_rx
+  #(parameter FIFOSIZE = 9)
+    (input clk,
+     input rst,
+     
+     // RX HW Interface
+     input ser_rx_clk,
+     input [15:0] ser_r,
+     input ser_rklsb,
+     input ser_rkmsb,
+     
+     output [31:0] wr_dat_o,
+     output [3:0] wr_flags_o,
+     input wr_ready_i,
+     output wr_ready_o,
+     
+     output [15:0] fifo_space,
+     output xon_rcvd, output xoff_rcvd,
+
+     output [15:0] fifo_occupied, output fifo_full, output fifo_empty,
+     output reg serdes_link_up,
+     output [31:0] debug
+     );
+
+   localparam K_COMMA = 8'b101_11100;     // 0xBC K28.5
+   localparam K_IDLE = 8'b001_11100;      // 0x3C K28.1
+   localparam K_PKT_START = 8'b110_11100; // 0xDC K28.6
+   localparam K_PKT_END = 8'b100_11100;   // 0x9C K28.4
+   localparam K_XON = 8'b010_11100;       // 0x5C K28.2
+   localparam K_XOFF = 8'b011_11100;      // 0x7C K28.3
+   localparam K_LOS = 8'b111_11111;       // 0xFF K31.7
+   localparam K_ERROR = 8'b000_00000;     // 0x00 K00.0
+   localparam D_56 = 8'b110_00101;        // 0xC5 D05.6
+   
+   localparam IDLE = 3'd0;
+   localparam FIRSTLINE1 = 3'd1;
+   localparam FIRSTLINE2 = 3'd2;
+   localparam PKT1 = 3'd3;
+   localparam PKT2 = 3'd4;
+   localparam CRC_CHECK = 3'd5;
+   localparam ERROR = 3'd6;
+   localparam DONE = 3'd7;
+   
+   wire [17:0] even_data;
+   reg [17:0]  odd_data;
+   wire [17:0] chosen_data;
+   reg 	       odd;
+   
+   reg [31:0]  line_i;
+   reg 	       sop_i, eop_i, error_i;
+   wire        error_o, sop_o, eop_o, write;
+   reg [15:0]  halfline;
+   reg [8:0]   holder;
+   wire [31:0] line_o;
+   
+   reg [2:0]   state;
+
+   reg [15:0]  CRC;
+   wire [15:0] nextCRC;
+   reg 	       write_d;
+
+   wire        rst_rxclk;
+   wire        have_space;
+
+   oneshot_2clk rst_1s(.clk_in(clk),.in(rst),.clk_out(ser_rx_clk),.out(rst_rxclk));
+
+   assign      even_data = {ser_rkmsb,ser_rklsb,ser_r};
+   
+   always @(posedge ser_rx_clk)
+     if(rst_rxclk)
+       holder <= 9'd0;
+     else
+       holder <= {even_data[17],even_data[15:8]};
+   
+   always @(posedge ser_rx_clk)
+     if(rst_rxclk)
+       odd_data <= 18'd0;
+     else
+       odd_data <= {even_data[16],holder[8],even_data[7:0],holder[7:0]};
+   
+   assign      chosen_data = odd ? odd_data : even_data;
+
+   // Transfer xon and xoff info to the main system clock for flow control purposes
+   reg 	       xon_rcvd_rxclk, xoff_rcvd_rxclk;
+   always @(posedge ser_rx_clk)
+     xon_rcvd_rxclk = ({1'b1,K_XON} == {ser_rkmsb,ser_r[15:8]}) | ({1'b1,K_XON} == {ser_rklsb,ser_r[7:0]} );
+   always @(posedge ser_rx_clk)
+     xoff_rcvd_rxclk = ({1'b1,K_XOFF} == {ser_rkmsb,ser_r[15:8]}) | ({1'b1,K_XOFF} == {ser_rklsb,ser_r[7:0]} );
+   
+   oneshot_2clk xon_1s(.clk_in(ser_rx_clk),.in(xon_rcvd_rxclk),.clk_out(clk),.out(xon_rcvd));
+   oneshot_2clk xoff_1s(.clk_in(ser_rx_clk),.in(xoff_rcvd_rxclk),.clk_out(clk),.out(xoff_rcvd));
+
+   // If the other side is sending xon or xoff, or is flow controlled (b/c we told them to be), don't fill the fifos
+   wire        wait_here = ((chosen_data == {2'b10,K_COMMA,D_56})||
+			    (chosen_data == {2'b11,K_XON,K_XON})||
+			    (chosen_data == {2'b11,K_XOFF,K_XOFF}) );
+
+   always @(posedge ser_rx_clk)
+     if(rst_rxclk) sop_i <= 0;
+     else if(state == FIRSTLINE1) sop_i <= 1;
+     else if(write_d) sop_i <= 0;
+   
+   reg 	       write_pre;
+   always @(posedge ser_rx_clk)
+     if(rst_rxclk)
+       begin
+	  state <= IDLE;
+	  odd <= 0;
+	  halfline <= 0;
+	  line_i <= 0;
+	  eop_i <= 0;
+	  error_i <= 0;
+	  write_pre <= 0;
+       end
+     else
+       case(state)
+	 IDLE :
+	   begin
+	      error_i <= 0;
+	      write_pre <= 0;
+	      if(even_data == {2'b11,K_PKT_START,K_PKT_START})
+		begin
+		   state <= FIRSTLINE1;
+		   odd <= 0;
+		end
+	      else if(odd_data == {2'b11,K_PKT_START,K_PKT_START})
+		begin
+		   state <= FIRSTLINE1;
+		   odd <= 1;
+		end
+	   end
+
+	 FIRSTLINE1 :
+	   if(chosen_data[17:16] == 0)
+	     begin
+		halfline <= chosen_data[15:0];
+		state <= FIRSTLINE2;
+	     end
+	   else if(wait_here)
+	     ;  // Flow Controlled, so wait here and do nothing
+	   else
+	     state <= ERROR;
+
+	 FIRSTLINE2 :
+	   if(chosen_data[17:16] == 0)
+	     begin
+		line_i <= {chosen_data[15:0],halfline};
+		if(~have_space)  // No space to write to!  Should have been avoided by flow control
+		  state <= ERROR;
+		else
+		  begin
+		     state <= PKT1;
+		     write_pre <= 1;
+		  end
+	     end // if (chosen_data[17:16] == 0)
+	   else if(wait_here)
+	     ;  // Flow Controlled, so wait here and do nothing
+	   else
+	     state <= ERROR;
+	 
+	 PKT1 :
+	   begin
+	      write_pre <= 0;
+	      if(chosen_data[17:16] == 0)
+		begin
+		   halfline <= chosen_data[15:0];
+		   state <= PKT2;
+		end
+	      else if(wait_here)
+		;  // Flow Controlled
+	      else if(chosen_data == {2'b11,K_PKT_END,K_PKT_END})
+	  	state <= CRC_CHECK;
+	      else
+		state <= ERROR;
+	   end // case: PKT1
+	 
+	 PKT2 :
+	   if(chosen_data[17:16] == 0)
+	     begin
+		line_i <= {1'b0,1'b0,1'b0,chosen_data[15:0],halfline};
+		if(~have_space)  // No space to write to!
+		  state <= ERROR;
+		else
+		  begin
+		     state <= PKT1;
+		     write_pre <= 1;
+		  end
+	     end // if (chosen_data[17:16] == 0)
+	   else if(wait_here)
+	     ;  // Flow Controlled
+	   else
+	     state <= ERROR;
+	   
+	 CRC_CHECK :
+	   if(chosen_data[17:0] == {2'b00,CRC})
+	     begin
+		if(~have_space)
+		  state <= ERROR;
+		else
+		  begin
+		     eop_i <= 1;
+		     state <= DONE;
+		  end
+	     end
+	   else if(wait_here)
+	     ;
+	   else
+	     state <= ERROR;
+	 
+	 ERROR :
+	   begin
+	      error_i <= 1;
+	      if(have_space)
+		state <= IDLE;
+	   end
+	 DONE :
+	   begin
+	      state <= IDLE;
+	      eop_i <= 0;
+	   end
+	      
+       endcase // case(state)
+   
+   
+   always @(posedge ser_rx_clk)
+     if(rst_rxclk)
+       CRC <= 16'hFFFF;
+     else if(state == IDLE)
+       CRC <= 16'hFFFF;
+     else if(chosen_data[17:16] == 2'b00)
+       CRC <= nextCRC;
+
+   CRC16_D16 crc_blk(chosen_data[15:0],CRC,nextCRC);
+
+   always @(posedge ser_rx_clk)
+     if(rst_rxclk) write_d <= 0;
+     else write_d <= write_pre;
+
+   // Internal FIFO, size 9 is 2K, size 10 is 4K Bytes
+   assign write = eop_i | (error_i & have_space) | (write_d & (state != CRC_CHECK));
+
+   fifo_2clock_cascade #(.WIDTH(35),.SIZE(FIFOSIZE)) serdes_rx_fifo
+     (.arst(rst),
+      .wclk(ser_rx_clk),.datain({error_i,sop_i,eop_i,line_i}), 
+      .src_rdy_i(write), .dst_rdy_o(have_space), .space(fifo_space), 
+      .rclk(clk),.dataout({error_o,sop_o,eop_o,line_o}), 
+      .src_rdy_o(wr_ready_o), .dst_rdy_i(wr_ready_i), .occupied(fifo_occupied) );
+
+   assign 	       fifo_full = ~have_space;   // Note -- in the wrong clock domain
+   assign 	       fifo_empty = ~wr_ready_o;
+   
+   // Internal FIFO to Buffer interface
+   assign wr_dat_o 		      = line_o;
+   assign wr_flags_o = { 2'b00, eop_o | error_o, sop_o | error_o };
+   
+   wire slu = ~(({2'b11,K_ERROR,K_ERROR}=={ser_rkmsb,ser_rklsb,ser_r}) ||
+		       ({2'b11,K_LOS,K_LOS}=={ser_rkmsb,ser_rklsb,ser_r}));
+   
+   reg [3:0]   slu_reg;
+   
+   always @(posedge clk)
+     if(rst) slu_reg <= 0;
+     else slu_reg <= {slu_reg[2:0],slu};
+
+   always @(posedge clk)
+     serdes_link_up <= &slu_reg[3:1];
+   
+   assign      debug = { have_space, wr_ready_o, odd, sop_i, eop_i, error_i, state[2:0] };
+   
+endmodule // serdes_rx