Reorganized firmware/ subdirectory (x300->usrp3, zpu->usrp2)

1 files changed, 235 insertions, 0 deletions

diff --git a/firmware/usrp2/usrp2p/eth_phy.h b/firmware/usrp2/usrp2p/eth_phy.h
new file mode 100644
index 000000000..d233e96e8
--- /dev/null
+++ b/firmware/usrp2/usrp2p/eth_phy.h
@@ -0,0 +1,235 @@
+/* -*- c -*- */
+/*
+ * Copyright 2007 Free Software Foundation, Inc.
+ * Copyright(c) 1999 - 2005 Intel Corporation. All rights reserved.
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+/* Much of this was extracted from the Linux e1000_hw.h file */
+
+#ifndef INCLUDED_ETH_PHY_H
+#define INCLUDED_ETH_PHY_H
+
+/* PHY 1000 MII Register/Bit Definitions */
+/* PHY Registers defined by IEEE */
+
+#define PHY_CTRL         0x00 /* Control Register */
+#define PHY_STATUS       0x01 /* Status Regiser */
+#define PHY_ID1          0x02 /* Phy Id Reg (word 1) */
+#define PHY_ID2          0x03 /* Phy Id Reg (word 2) */
+#define PHY_AUTONEG_ADV  0x04 /* Autoneg Advertisement */
+#define PHY_LP_ABILITY   0x05 /* Link Partner Ability (Base Page) */
+#define PHY_AUTONEG_EXP  0x06 /* Autoneg Expansion Reg */
+#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */
+#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */
+#define PHY_1000T_CTRL   0x09 /* 1000Base-T Control Reg */
+#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
+#define PHY_EXT_STATUS   0x0F /* Extended Status Reg */
+
+/* PHY 1000 MII Register additions in ET1011C */
+#define PHY_INT_MASK     24
+#define PHY_INT_STATUS   25
+#define PHY_PHY_STATUS   26
+#define PHY_LED2         28
+
+/* Bit definitions for some of the registers above */
+
+/* PHY Control Register (PHY_CTRL) */
+#define MII_CR_SPEED_SELECT_MSB 0x0040  /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_COLL_TEST_ENABLE 0x0080  /* Collision test enable */
+#define MII_CR_FULL_DUPLEX      0x0100  /* FDX =1, half duplex =0 */
+#define MII_CR_RESTART_AUTO_NEG 0x0200  /* Restart auto negotiation */
+#define MII_CR_ISOLATE          0x0400  /* Isolate PHY from MII */
+#define MII_CR_POWER_DOWN       0x0800  /* Power down */
+#define MII_CR_AUTO_NEG_EN      0x1000  /* Auto Neg Enable */
+#define MII_CR_SPEED_SELECT_LSB 0x2000  /* bits 6,13: 10=1000, 01=100, 00=10 */
+#define MII_CR_LOOPBACK         0x4000  /* 0 = normal, 1 = loopback */
+#define MII_CR_RESET            0x8000  /* 0 = normal, 1 = PHY reset */
+
+/* PHY Status Register (PHY_STATUS) */
+#define MII_SR_EXTENDED_CAPS     0x0001 /* Extended register capabilities */
+#define MII_SR_JABBER_DETECT     0x0002 /* Jabber Detected */
+#define MII_SR_LINK_STATUS       0x0004 /* Link Status 1 = link */
+#define MII_SR_AUTONEG_CAPS      0x0008 /* Auto Neg Capable */
+#define MII_SR_REMOTE_FAULT      0x0010 /* Remote Fault Detect */
+#define MII_SR_AUTONEG_COMPLETE  0x0020 /* Auto Neg Complete */
+#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
+#define MII_SR_EXTENDED_STATUS   0x0100 /* Ext. status info in Reg 0x0F */
+#define MII_SR_100T2_HD_CAPS     0x0200 /* 100T2 Half Duplex Capable */
+#define MII_SR_100T2_FD_CAPS     0x0400 /* 100T2 Full Duplex Capable */
+#define MII_SR_10T_HD_CAPS       0x0800 /* 10T   Half Duplex Capable */
+#define MII_SR_10T_FD_CAPS       0x1000 /* 10T   Full Duplex Capable */
+#define MII_SR_100X_HD_CAPS      0x2000 /* 100X  Half Duplex Capable */
+#define MII_SR_100X_FD_CAPS      0x4000 /* 100X  Full Duplex Capable */
+#define MII_SR_100T4_CAPS        0x8000 /* 100T4 Capable */
+
+/* Autoneg Advertisement Register (PHY_AUTONEG_ADV) */
+#define NWAY_AR_SELECTOR_FIELD 0x0001   /* indicates IEEE 802.3 CSMA/CD */
+#define NWAY_AR_10T_HD_CAPS    0x0020   /* 10T   Half Duplex Capable */
+#define NWAY_AR_10T_FD_CAPS    0x0040   /* 10T   Full Duplex Capable */
+#define NWAY_AR_100TX_HD_CAPS  0x0080   /* 100TX Half Duplex Capable */
+#define NWAY_AR_100TX_FD_CAPS  0x0100   /* 100TX Full Duplex Capable */
+#define NWAY_AR_100T4_CAPS     0x0200   /* 100T4 Capable */
+#define NWAY_AR_PAUSE          0x0400   /* Pause operation desired */
+#define NWAY_AR_ASM_DIR        0x0800   /* Asymmetric Pause Direction bit */
+#define NWAY_AR_REMOTE_FAULT   0x2000   /* Remote Fault detected */
+#define NWAY_AR_NEXT_PAGE      0x8000   /* Next Page ability supported */
+
+/* Link Partner Ability Register (Base Page) (PHY_LP_ABILITY) */
+#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */
+#define NWAY_LPAR_10T_HD_CAPS    0x0020 /* LP is 10T   Half Duplex Capable */
+#define NWAY_LPAR_10T_FD_CAPS    0x0040 /* LP is 10T   Full Duplex Capable */
+#define NWAY_LPAR_100TX_HD_CAPS  0x0080 /* LP is 100TX Half Duplex Capable */
+#define NWAY_LPAR_100TX_FD_CAPS  0x0100 /* LP is 100TX Full Duplex Capable */
+#define NWAY_LPAR_100T4_CAPS     0x0200 /* LP is 100T4 Capable */
+#define NWAY_LPAR_PAUSE          0x0400 /* LP Pause operation desired */
+#define NWAY_LPAR_ASM_DIR        0x0800 /* LP Asymmetric Pause Direction bit */
+#define NWAY_LPAR_REMOTE_FAULT   0x2000 /* LP has detected Remote Fault */
+#define NWAY_LPAR_ACKNOWLEDGE    0x4000 /* LP has rx'd link code word */
+#define NWAY_LPAR_NEXT_PAGE      0x8000 /* Next Page ability supported */
+
+/* Autoneg Expansion Register (PHY_AUTONEG_EXP) */
+#define NWAY_ER_LP_NWAY_CAPS      0x0001 /* LP has Auto Neg Capability */
+#define NWAY_ER_PAGE_RXD          0x0002 /* LP is 10T   Half Duplex Capable */
+#define NWAY_ER_NEXT_PAGE_CAPS    0x0004 /* LP is 10T   Full Duplex Capable */
+#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */
+#define NWAY_ER_PAR_DETECT_FAULT  0x0010 /* LP is 100TX Full Duplex Capable */
+
+/* Next Page TX Register (PHY_NEXT_PAGE_TX) */
+#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define NPTX_TOGGLE         0x0800 /* Toggles between exchanges
+                                    * of different NP
+                                    */
+#define NPTX_ACKNOWLDGE2    0x1000 /* 1 = will comply with msg
+                                    * 0 = cannot comply with msg
+                                    */
+#define NPTX_MSG_PAGE       0x2000 /* formatted(1)/unformatted(0) pg */
+#define NPTX_NEXT_PAGE      0x8000 /* 1 = addition NP will follow
+                                    * 0 = sending last NP
+                                    */
+
+/* Link Partner Next Page Register (PHY_LP_NEXT_PAGE) */
+#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */
+#define LP_RNPR_TOGGLE         0x0800 /* Toggles between exchanges
+                                       * of different NP
+                                       */
+#define LP_RNPR_ACKNOWLDGE2    0x1000 /* 1 = will comply with msg
+                                       * 0 = cannot comply with msg
+                                       */
+#define LP_RNPR_MSG_PAGE       0x2000  /* formatted(1)/unformatted(0) pg */
+#define LP_RNPR_ACKNOWLDGE     0x4000  /* 1 = ACK / 0 = NO ACK */
+#define LP_RNPR_NEXT_PAGE      0x8000  /* 1 = addition NP will follow
+                                        * 0 = sending last NP
+                                        */
+
+/* 1000BASE-T Control Register (PHY_1000T_CTRL) */
+#define CR_1000T_ASYM_PAUSE      0x0080 /* Advertise asymmetric pause bit */
+#define CR_1000T_HD_CAPS         0x0100 /* Advertise 1000T HD capability */
+#define CR_1000T_FD_CAPS         0x0200 /* Advertise 1000T FD capability  */
+#define CR_1000T_REPEATER_DTE    0x0400 /* 1=Repeater/switch device port */
+                                        /* 0=DTE device */
+#define CR_1000T_MS_VALUE        0x0800 /* 1=Configure PHY as Master */
+                                        /* 0=Configure PHY as Slave */
+#define CR_1000T_MS_ENABLE       0x1000 /* 1=Master/Slave manual config value */
+                                        /* 0=Automatic Master/Slave config */
+#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
+#define CR_1000T_TEST_MODE_1     0x2000 /* Transmit Waveform test */
+#define CR_1000T_TEST_MODE_2     0x4000 /* Master Transmit Jitter test */
+#define CR_1000T_TEST_MODE_3     0x6000 /* Slave Transmit Jitter test */
+#define CR_1000T_TEST_MODE_4     0x8000 /* Transmitter Distortion test */
+
+/* 1000BASE-T Status Register (PHY_1000T_STATUS) */
+#define SR_1000T_IDLE_ERROR_CNT   0x00FF /* Num idle errors since last read */
+#define SR_1000T_ASYM_PAUSE_DIR   0x0100 /* LP asymmetric pause direction bit */
+#define SR_1000T_LP_HD_CAPS       0x0400 /* LP is 1000T HD capable */
+#define SR_1000T_LP_FD_CAPS       0x0800 /* LP is 1000T FD capable */
+#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
+#define SR_1000T_LOCAL_RX_STATUS  0x2000 /* Local receiver OK */
+#define SR_1000T_MS_CONFIG_RES    0x4000 /* 1=Local TX is Master, 0=Slave */
+#define SR_1000T_MS_CONFIG_FAULT  0x8000 /* Master/Slave config fault */
+#define SR_1000T_REMOTE_RX_STATUS_SHIFT          12
+#define SR_1000T_LOCAL_RX_STATUS_SHIFT           13
+#define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT    5
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_20            20
+#define FFE_IDLE_ERR_COUNT_TIMEOUT_100           100
+
+/* Extended Status Register (PHY_EXT_STATUS) */
+#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */
+#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */
+#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */
+#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */
+
+#define PHY_TX_POLARITY_MASK   0x0100 /* register 10h bit 8 (polarity bit) */
+#define PHY_TX_NORMAL_POLARITY 0      /* register 10h bit 8 (normal polarity) */
+
+#define AUTO_POLARITY_DISABLE  0x0010 /* register 11h bit 4 */
+                                      /* (0=enable, 1=disable) */
+
+/* PHY Status Register (PHY_PHY_STATUS) */
+#define PHYSTAT_ASYMMETRIC   (1 << 0)
+#define PHYSTAT_PAUSE        (1 << 1)
+#define PHYSTAT_AUTONEG_EN   (1 << 2)
+#define PHYSTAT_COLLISION    (1 << 3)
+#define PHYSTAT_RXSTAT       (1 << 4)
+#define PHYSTAT_TXSTAT       (1 << 5)
+#define PHYSTAT_LINK         (1 << 6)
+#define PHYSTAT_DUPLEX       (1 << 7)
+#define PHYSTAT_SPEED_MASK   ((1 << 8) | (1 << 9))
+#define PHYSTAT_SPEED_1000   (1 << 9)
+#define PHYSTAT_SPEED_100    (1 << 8)
+#define PHYSTAT_SPEED_10     0
+#define PHYSTAT_POLARITY     (1 << 10)
+#define PHYSTAT_MDIX         (1 << 11)
+#define PHYSTAT_AUTONEG_STAT (1 << 12)
+#define PHYSTAT_STANDBY      (1 << 13)
+
+/* Interrupt status, mask and clear regs (PHY_INT_{STATUS,MASK,CLEAR}) */
+#define PHY_INT_ENABLE         (1 << 0)
+#define PHY_INT_DOWNSHIFT      (1 << 1)
+#define PHY_INT_LINK_STATUS_CHANGE  (1 << 2)
+#define PHY_INT_RX_STATUS_CHANGE (1 << 3)
+#define PHY_INT_FIFO_ERROR     (1 << 4)
+#define PHY_INT_ERR_CTR_FULL   (1 << 5)
+#define PHY_INT_NEXT_PAGE_RX   (1 << 6)
+#define PHY_INT_CRC_ERROR      (1 << 7)
+#define PHY_INT_AUTONEG_STATUS_CHANGE (1 << 8)
+#define PHY_INT_MDIO_SYNC_LOST (1 << 9)
+#define PHY_INT_TDR_IP_PHONE   (1 << 10)
+
+/* PHY LED status register 2 (used for controlling link LED for activity light) */
+#define PHY_LED_TXRX_LSB           12
+#define PHY_LED_LINK_LSB           8
+#define PHY_LED_100_LSB            4
+#define PHY_LED_1000_LSB           0
+
+#define LED_1000                   0
+#define LED_100_TX                 1
+#define LED_10                     2
+#define LED_1000_ON_100_BLINK      3
+#define LED_LINK                   4
+#define LED_TX                     5
+#define LED_RX                     6
+#define LED_ACTIVITY               7
+#define LED_FULLDUPLEX             8
+#define LED_COLLISION              9
+#define LED_LINK_ON_ACTIVITY_BLINK 10
+#define LED_LINK_ON_RX_BLINK       11
+#define LED_FULL_DUPLEX_ON_COLLISION_BLINK 12
+#define LED_BLINK                  13
+#define LED_ON                     14
+#define LED_OFF                    15
+
+
+#endif /* INCLUDED_ETH_PHY_H */