Merge branch 'new_eth' of http://gnuradio.org/git/matt into master

* 'new_eth' of http://gnuradio.org/git/matt: (42 commits)
  Fix warnings, mostly from implicitly defined wires or unspecified widths
  fullchip sim now compiles again, after moving eth and models over to new simple_gemac
  remove unused opencores
  remove debugging code
  no idea where this came from, it shouldn't be here
  Copied wb_1master back from quad radio
  Remove old mac.  Good riddance.
  remove unused port
  More xilinx fifos, more clean up of our fifos
  might as well use a cascade fifo to help timing and give a little more capacity
  fix a typo which caused tx glitches
  Untested fixes for getting serdes onto the new fifo system.  Compiles, at least
  Implement Eth flow control using pause frames
  parameterized fifo sizes, some reformatting
  remove unused old style fifo
  allow control of whether or not to honor flow control, adds some debug lines
  debug the rx side
  no longer used, replaced by newfifo version
  remove special last_line adjustment from ethernet port
  Firmware now inserts mac source address value in each frame.
  ...

1 files changed, 0 insertions, 86 deletions

diff --git a/eth/rtl/verilog/flow_ctrl_rx.v b/eth/rtl/verilog/flow_ctrl_rx.v
deleted file mode 100644
index 6654c626b..000000000
--- a/eth/rtl/verilog/flow_ctrl_rx.v
+++ /dev/null
@@ -1,86 +0,0 @@
-

-// RX side of flow control -- when we are running out of RX space, send a PAUSE

-

-module flow_ctrl_rx

-  (input        rst,

-   //host processor

-   input        pause_frame_send_en,

-   input [15:0] pause_quanta_set,

-   input [15:0] fc_hwmark,

-   input [15:0] fc_lwmark,

-   input [15:0] fc_padtime,

-   // From MAC_rx_ctrl

-   input        rx_clk,

-   input [15:0] rx_fifo_space,

-   // MAC_tx_ctrl

-   input        tx_clk,

-   output reg   xoff_gen,

-   output reg   xon_gen,

-   input        xoff_gen_complete,

-   input        xon_gen_complete

-   );

-   

-   // ******************************************************************************        

-   // Force our TX to send a PAUSE frame because our RX is nearly full

-   // ******************************************************************************

-

-   reg xon_int, xoff_int;

-   reg [21:0] countdown;

- 

-   always @(posedge rx_clk or posedge rst)

-     if(rst)

-       begin

-	  xon_int <= 0;

-	  xoff_int <= 0;

-       end

-     else 

-       begin

-	  xon_int <= 0;

-	  xoff_int <= 0;

-	  if(pause_frame_send_en)

-	    if(countdown == 0)

-	      if(rx_fifo_space < fc_lwmark)

-		xoff_int <= 1;

-	      else

-		;

-	    else

-	      if(rx_fifo_space > fc_hwmark)

-		xon_int <= 1;

-       end // else: !if(rst)

-   

-   reg xoff_int_d1, xon_int_d1;

-

-   always @(posedge rx_clk)

-     xon_int_d1 <= xon_int;

-   always @(posedge rx_clk)

-     xoff_int_d1 <= xoff_int;

-   

-   always @ (posedge tx_clk or posedge rst)

-     if (rst)

-       xoff_gen        <=0;

-     else if (xoff_gen_complete)

-       xoff_gen        <=0;

-     else if (xoff_int | xoff_int_d1)

-       xoff_gen        <=1;

-   

-   always @ (posedge tx_clk or posedge rst)

-     if (rst)

-       xon_gen     <=0;

-     else if (xon_gen_complete)

-       xon_gen     <=0;

-     else if (xon_int | xon_int_d1)

-       xon_gen     <=1;                     

-

-   wire [21:0] pq_reduced = {pause_quanta_set,6'd0} - {6'd0,fc_padtime};

-   

-   always @(posedge tx_clk or posedge rst)

-     if(rst)

-       countdown <= 0;

-     else if(xoff_gen)

-       countdown <= pq_reduced;

-     else if(xon_gen)

-       countdown <= 0;

-     else if(countdown != 0)

-       countdown <= countdown - 1;

-   

-endmodule // flow_ctrl