aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Simplify buttons inputMatthias P. Braendli2020-12-184-101/+28
|
* LCD: fix setup and hold for I2C commandsMatthias P. Braendli2020-12-183-3/+42
|
* Power decoupling and IF improvementsMatthias P. Braendli2020-12-158-562/+594
|
* Update XTAL IF filterMatthias P. Braendli2020-12-141-26/+26
|
* Move to 6MHz IFMatthias P. Braendli2020-12-123-19/+19
|
* Add IF amp boardMatthias P. Braendli2020-12-086-3/+2193
|
* Update READMEMatthias P. Braendli2020-12-073-4/+17
|
* Fix PTT, add AGC readoutMatthias P. Braendli2020-12-074-18/+131
|
* Rework UIMatthias P. Braendli2020-12-073-179/+309
|
* Add T/R sequencerMatthias P. Braendli2020-12-071-23/+80
|
* Update firmware for new LOMatthias P. Braendli2020-11-294-21/+24
|
* Apply a few LO board correctionsMatthias P. Braendli2020-11-292-841/+857
|
* Some changes on picardy boardMatthias P. Braendli2020-11-246-4647/+4678
|
* Add LO board, sent to manufacturingMatthias P. Braendli2020-11-248-1/+4450
|
* Fix buttons and filter frequencies for LSB and USBMatthias P. Braendli2020-08-284-847/+954
|
* Continue TX assembly, update versionsMatthias P. Braendli2020-08-2810-4736/+4887
|
* Connect voltage switch relayMatthias P. Braendli2020-07-247-55/+158
|
* Configure i2c2 for displayMatthias P. Braendli2020-07-231-18/+35
|
* Add picardy firmware projectMatthias P. Braendli2020-07-2215-0/+103020
|
* Adapt component values as assembledMatthias P. Braendli2020-07-223-22/+25
|
* SW: handle buttonsMatthias P. Braendli2020-07-175-127/+388
|
* Add a few readme embellishmentsMatthias P. Braendli2020-07-081-33/+34
|
* Clarify licencesMatthias P. Braendli2020-07-084-4/+254
|
* Prepare manufacturing filesmanufacture_20200708Matthias P. Braendli2020-07-081-6/+6
|
* Explicitly connect GND and GNDA, add USB ID resistorMatthias P. Braendli2020-07-083-9861/+9908
|
* Apply PCB fixes and add logos and textMatthias P. Braendli2020-07-061-12038/+12520
|
* Use 6 crystals for IF filterMatthias P. Braendli2020-06-302-5853/+6040
|
* Check mic pinout and add ferrite beadsMatthias P. Braendli2020-06-303-7340/+7533
|
* Set VFO with encoderMatthias P. Braendli2020-06-292-52/+43
|
* Configure quadrature decoderMatthias P. Braendli2020-06-281-3/+15
|
* Add uFL for VHF LOMatthias P. Braendli2020-06-284-6736/+6666
|
* sw: configure si5351Matthias P. Braendli2020-06-2859-8/+3265
|
* Get LCD and Si5351 I2C to workMatthias P. Braendli2020-06-135-93/+283
|
* Use proper target for stm32f103Matthias P. Braendli2020-06-131-2/+2
|
* Add RESETn to PROG headerMatthias P. Braendli2020-06-043-7459/+7733
|
* Put LCD on I2C2, use global nets for powerMatthias P. Braendli2020-05-196-8615/+8790
|
* Case edge alignment for connectors, add unused uC pins to headerMatthias P. Braendli2020-04-195-10447/+10839
|
* Add demo1 stm32f103 example with blinky codeMatthias P. Braendli2020-04-109-0/+417
|
* Clarify README detailmanufacture_eval_20200409Matthias P. Braendli2020-04-091-0/+1
|
* Add eval pcb for clock and stm32Matthias P. Braendli2020-04-095-0/+9020
|
* Replace atmega by stm32f103Matthias P. Braendli2020-04-074-9507/+10859
|
* Add frontpanel drawingMatthias P. Braendli2020-03-294-5053/+6575
|
* Add plan B for CWMatthias P. Braendli2020-03-292-13/+31
|
* Some control.sch changesMatthias P. Braendli2020-03-292-5410/+5601
|
* Replace relay switchingMatthias P. Braendli2020-03-188-7177/+6696
|
* README: develop assembly and test planMatthias P. Braendli2020-03-171-4/+69
|
* Parts replacements, external volume potentiometerMatthias P. Braendli2020-03-177-8893/+9143
|
* Replace DC switching by a relayMatthias P. Braendli2020-03-146-10379/+10815
|
* Change board outline for 1455N1201 enclosureMatthias P. Braendli2020-03-112-8993/+7740
|
* Replace mic amp, reroute, improve silkscreenMatthias P. Braendli2020-03-105-9146/+9880
|
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-22 19:08:38 +0000