Commit message (Expand) | Author | Age | Files | Lines | ||
---|---|---|---|---|---|---|
... | ||||||
* | Get FELDHELL to work | Matthias P. Braendli | 2021-04-15 | 8 | -57/+882 | |
* | Update gitignore | Matthias P. Braendli | 2021-04-08 | 1 | -0/+9 | |
* | Add some QUCS files | Matthias P. Braendli | 2021-04-08 | 14 | -0/+9974 | |
* | Make cw key active low | Matthias P. Braendli | 2021-04-02 | 2 | -12/+11 | |
* | Enable USB CDC ACM for eval-clock-cw-tx | Matthias P. Braendli | 2021-03-31 | 5 | -2/+140 | |
* | Work on eval-clock-cw-tx sequencing | Matthias P. Braendli | 2021-03-29 | 4 | -28/+44 | |
* | Create eval-clock-cw-tx sw | Matthias P. Braendli | 2021-03-20 | 17 | -0/+103724 | |
* | Separate LM386 muting from switching, slow down a T/R switch a bit | Matthias P. Braendli | 2021-03-05 | 2 | -1/+14 | |
* | Some updates to improve PTT clicking | Matthias P. Braendli | 2021-03-05 | 2 | -30/+43 | |
* | Calibrate S meter | Matthias P. Braendli | 2021-02-17 | 2 | -10/+31 | |
* | Add some schematic notes | Matthias P. Braendli | 2021-02-17 | 6 | -315/+517 | |
* | Fix keyer timing | Matthias P. Braendli | 2021-01-31 | 1 | -2/+14 | |
* | Add CW keyer | Matthias P. Braendli | 2021-01-31 | 5 | -84/+317 | |
* | Implement CW with tone injection | Matthias P. Braendli | 2021-01-30 | 6 | -125/+222 | |
* | Update README | Matthias P. Braendli | 2021-01-24 | 3 | -15/+28 | |
* | Update README, notes and Qucs BPF145 | Matthias P. Braendli | 2020-12-28 | 3 | -9/+21 | |
* | Add disabled CW, replace sequencer, ticks and set VFO/BFO logic | Matthias P. Braendli | 2020-12-24 | 6 | -50/+112 | |
* | Switch clock timer to TIM2 | Matthias P. Braendli | 2020-12-22 | 3 | -12/+22 | |
* | Simplify buttons input | Matthias P. Braendli | 2020-12-18 | 4 | -101/+28 | |
* | LCD: fix setup and hold for I2C commands | Matthias P. Braendli | 2020-12-18 | 3 | -3/+42 | |
* | Power decoupling and IF improvements | Matthias P. Braendli | 2020-12-15 | 8 | -562/+594 | |
* | Update XTAL IF filter | Matthias P. Braendli | 2020-12-14 | 1 | -26/+26 | |
* | Move to 6MHz IF | Matthias P. Braendli | 2020-12-12 | 3 | -19/+19 | |
* | Add IF amp board | Matthias P. Braendli | 2020-12-08 | 6 | -3/+2193 | |
* | Update README | Matthias P. Braendli | 2020-12-07 | 3 | -4/+17 | |
* | Fix PTT, add AGC readout | Matthias P. Braendli | 2020-12-07 | 4 | -18/+131 | |
* | Rework UI | Matthias P. Braendli | 2020-12-07 | 3 | -179/+309 | |
* | Add T/R sequencer | Matthias P. Braendli | 2020-12-07 | 1 | -23/+80 | |
* | Update firmware for new LO | Matthias P. Braendli | 2020-11-29 | 4 | -21/+24 | |
* | Apply a few LO board corrections | Matthias P. Braendli | 2020-11-29 | 2 | -841/+857 | |
* | Some changes on picardy board | Matthias P. Braendli | 2020-11-24 | 6 | -4647/+4678 | |
* | Add LO board, sent to manufacturing | Matthias P. Braendli | 2020-11-24 | 8 | -1/+4450 | |
* | Fix buttons and filter frequencies for LSB and USB | Matthias P. Braendli | 2020-08-28 | 4 | -847/+954 | |
* | Continue TX assembly, update versions | Matthias P. Braendli | 2020-08-28 | 10 | -4736/+4887 | |
* | Connect voltage switch relay | Matthias P. Braendli | 2020-07-24 | 7 | -55/+158 | |
* | Configure i2c2 for display | Matthias P. Braendli | 2020-07-23 | 1 | -18/+35 | |
* | Add picardy firmware project | Matthias P. Braendli | 2020-07-22 | 15 | -0/+103020 | |
* | Adapt component values as assembled | Matthias P. Braendli | 2020-07-22 | 3 | -22/+25 | |
* | SW: handle buttons | Matthias P. Braendli | 2020-07-17 | 5 | -127/+388 | |
* | Add a few readme embellishments | Matthias P. Braendli | 2020-07-08 | 1 | -33/+34 | |
* | Clarify licences | Matthias P. Braendli | 2020-07-08 | 4 | -4/+254 | |
* | Prepare manufacturing filesmanufacture_20200708 | Matthias P. Braendli | 2020-07-08 | 1 | -6/+6 | |
* | Explicitly connect GND and GNDA, add USB ID resistor | Matthias P. Braendli | 2020-07-08 | 3 | -9861/+9908 | |
* | Apply PCB fixes and add logos and text | Matthias P. Braendli | 2020-07-06 | 1 | -12038/+12520 | |
* | Use 6 crystals for IF filter | Matthias P. Braendli | 2020-06-30 | 2 | -5853/+6040 | |
* | Check mic pinout and add ferrite beads | Matthias P. Braendli | 2020-06-30 | 3 | -7340/+7533 | |
* | Set VFO with encoder | Matthias P. Braendli | 2020-06-29 | 2 | -52/+43 | |
* | Configure quadrature decoder | Matthias P. Braendli | 2020-06-28 | 1 | -3/+15 | |
* | Add uFL for VHF LO | Matthias P. Braendli | 2020-06-28 | 4 | -6736/+6666 | |
* | sw: configure si5351 | Matthias P. Braendli | 2020-06-28 | 59 | -8/+3265 |