aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Make cw key active lowMatthias P. Braendli2021-04-022-12/+11
|
* Enable USB CDC ACM for eval-clock-cw-txMatthias P. Braendli2021-03-315-2/+140
|
* Work on eval-clock-cw-tx sequencingMatthias P. Braendli2021-03-294-28/+44
|
* Create eval-clock-cw-tx swMatthias P. Braendli2021-03-2017-0/+103724
|
* Separate LM386 muting from switching, slow down a T/R switch a bitMatthias P. Braendli2021-03-052-1/+14
|
* Some updates to improve PTT clickingMatthias P. Braendli2021-03-052-30/+43
|
* Calibrate S meterMatthias P. Braendli2021-02-172-10/+31
|
* Add some schematic notesMatthias P. Braendli2021-02-176-315/+517
|
* Fix keyer timingMatthias P. Braendli2021-01-311-2/+14
|
* Add CW keyerMatthias P. Braendli2021-01-315-84/+317
|
* Implement CW with tone injectionMatthias P. Braendli2021-01-306-125/+222
|
* Update READMEMatthias P. Braendli2021-01-243-15/+28
|
* Update README, notes and Qucs BPF145Matthias P. Braendli2020-12-283-9/+21
|
* Add disabled CW, replace sequencer, ticks and set VFO/BFO logicMatthias P. Braendli2020-12-246-50/+112
|
* Switch clock timer to TIM2Matthias P. Braendli2020-12-223-12/+22
|
* Simplify buttons inputMatthias P. Braendli2020-12-184-101/+28
|
* LCD: fix setup and hold for I2C commandsMatthias P. Braendli2020-12-183-3/+42
|
* Power decoupling and IF improvementsMatthias P. Braendli2020-12-158-562/+594
|
* Update XTAL IF filterMatthias P. Braendli2020-12-141-26/+26
|
* Move to 6MHz IFMatthias P. Braendli2020-12-123-19/+19
|
* Add IF amp boardMatthias P. Braendli2020-12-086-3/+2193
|
* Update READMEMatthias P. Braendli2020-12-073-4/+17
|
* Fix PTT, add AGC readoutMatthias P. Braendli2020-12-074-18/+131
|
* Rework UIMatthias P. Braendli2020-12-073-179/+309
|
* Add T/R sequencerMatthias P. Braendli2020-12-071-23/+80
|
* Update firmware for new LOMatthias P. Braendli2020-11-294-21/+24
|
* Apply a few LO board correctionsMatthias P. Braendli2020-11-292-841/+857
|
* Some changes on picardy boardMatthias P. Braendli2020-11-246-4647/+4678
|
* Add LO board, sent to manufacturingMatthias P. Braendli2020-11-248-1/+4450
|
* Fix buttons and filter frequencies for LSB and USBMatthias P. Braendli2020-08-284-847/+954
|
* Continue TX assembly, update versionsMatthias P. Braendli2020-08-2810-4736/+4887
|
* Connect voltage switch relayMatthias P. Braendli2020-07-247-55/+158
|
* Configure i2c2 for displayMatthias P. Braendli2020-07-231-18/+35
|
* Add picardy firmware projectMatthias P. Braendli2020-07-2215-0/+103020
|
* Adapt component values as assembledMatthias P. Braendli2020-07-223-22/+25
|
* SW: handle buttonsMatthias P. Braendli2020-07-175-127/+388
|
* Add a few readme embellishmentsMatthias P. Braendli2020-07-081-33/+34
|
* Clarify licencesMatthias P. Braendli2020-07-084-4/+254
|
* Prepare manufacturing filesmanufacture_20200708Matthias P. Braendli2020-07-081-6/+6
|
* Explicitly connect GND and GNDA, add USB ID resistorMatthias P. Braendli2020-07-083-9861/+9908
|
* Apply PCB fixes and add logos and textMatthias P. Braendli2020-07-061-12038/+12520
|
* Use 6 crystals for IF filterMatthias P. Braendli2020-06-302-5853/+6040
|
* Check mic pinout and add ferrite beadsMatthias P. Braendli2020-06-303-7340/+7533
|
* Set VFO with encoderMatthias P. Braendli2020-06-292-52/+43
|
* Configure quadrature decoderMatthias P. Braendli2020-06-281-3/+15
|
* Add uFL for VHF LOMatthias P. Braendli2020-06-284-6736/+6666
|
* sw: configure si5351Matthias P. Braendli2020-06-2859-8/+3265
|
* Get LCD and Si5351 I2C to workMatthias P. Braendli2020-06-135-93/+283
|
* Use proper target for stm32f103Matthias P. Braendli2020-06-131-2/+2
|
* Add RESETn to PROG headerMatthias P. Braendli2020-06-043-7459/+7733
|
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-18 10:50:44 +0000