aboutsummaryrefslogtreecommitdiffstats
Commit message (Expand)AuthorAgeFilesLines
* eval-clock-cw-tx LED is CW beepMatthias P. Braendli2021-05-221-10/+4
* Add sequencingMatthias P. Braendli2021-05-172-5/+9
* Get FELDHELL to workMatthias P. Braendli2021-04-158-57/+882
* Update gitignoreMatthias P. Braendli2021-04-081-0/+9
* Add some QUCS filesMatthias P. Braendli2021-04-0814-0/+9974
* Make cw key active lowMatthias P. Braendli2021-04-022-12/+11
* Enable USB CDC ACM for eval-clock-cw-txMatthias P. Braendli2021-03-315-2/+140
* Work on eval-clock-cw-tx sequencingMatthias P. Braendli2021-03-294-28/+44
* Create eval-clock-cw-tx swMatthias P. Braendli2021-03-2017-0/+103724
* Separate LM386 muting from switching, slow down a T/R switch a bitMatthias P. Braendli2021-03-052-1/+14
* Some updates to improve PTT clickingMatthias P. Braendli2021-03-052-30/+43
* Calibrate S meterMatthias P. Braendli2021-02-172-10/+31
* Add some schematic notesMatthias P. Braendli2021-02-176-315/+517
* Fix keyer timingMatthias P. Braendli2021-01-311-2/+14
* Add CW keyerMatthias P. Braendli2021-01-315-84/+317
* Implement CW with tone injectionMatthias P. Braendli2021-01-306-125/+222
* Update READMEMatthias P. Braendli2021-01-243-15/+28
* Update README, notes and Qucs BPF145Matthias P. Braendli2020-12-283-9/+21
* Add disabled CW, replace sequencer, ticks and set VFO/BFO logicMatthias P. Braendli2020-12-246-50/+112
* Switch clock timer to TIM2Matthias P. Braendli2020-12-223-12/+22
* Simplify buttons inputMatthias P. Braendli2020-12-184-101/+28
* LCD: fix setup and hold for I2C commandsMatthias P. Braendli2020-12-183-3/+42
* Power decoupling and IF improvementsMatthias P. Braendli2020-12-158-562/+594
* Update XTAL IF filterMatthias P. Braendli2020-12-141-26/+26
* Move to 6MHz IFMatthias P. Braendli2020-12-123-19/+19
* Add IF amp boardMatthias P. Braendli2020-12-086-3/+2193
* Update READMEMatthias P. Braendli2020-12-073-4/+17
* Fix PTT, add AGC readoutMatthias P. Braendli2020-12-074-18/+131
* Rework UIMatthias P. Braendli2020-12-073-179/+309
* Add T/R sequencerMatthias P. Braendli2020-12-071-23/+80
* Update firmware for new LOMatthias P. Braendli2020-11-294-21/+24
* Apply a few LO board correctionsMatthias P. Braendli2020-11-292-841/+857
* Some changes on picardy boardMatthias P. Braendli2020-11-246-4647/+4678
* Add LO board, sent to manufacturingMatthias P. Braendli2020-11-248-1/+4450
* Fix buttons and filter frequencies for LSB and USBMatthias P. Braendli2020-08-284-847/+954
* Continue TX assembly, update versionsMatthias P. Braendli2020-08-2810-4736/+4887
* Connect voltage switch relayMatthias P. Braendli2020-07-247-55/+158
* Configure i2c2 for displayMatthias P. Braendli2020-07-231-18/+35
* Add picardy firmware projectMatthias P. Braendli2020-07-2215-0/+103020
* Adapt component values as assembledMatthias P. Braendli2020-07-223-22/+25
* SW: handle buttonsMatthias P. Braendli2020-07-175-127/+388
* Add a few readme embellishmentsMatthias P. Braendli2020-07-081-33/+34
* Clarify licencesMatthias P. Braendli2020-07-084-4/+254
* Prepare manufacturing filesmanufacture_20200708Matthias P. Braendli2020-07-081-6/+6
* Explicitly connect GND and GNDA, add USB ID resistorMatthias P. Braendli2020-07-083-9861/+9908
* Apply PCB fixes and add logos and textMatthias P. Braendli2020-07-061-12038/+12520
* Use 6 crystals for IF filterMatthias P. Braendli2020-06-302-5853/+6040
* Check mic pinout and add ferrite beadsMatthias P. Braendli2020-06-303-7340/+7533
* Set VFO with encoderMatthias P. Braendli2020-06-292-52/+43
* Configure quadrature decoderMatthias P. Braendli2020-06-281-3/+15
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-22 00:35:42 +0000