1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
|
//
// FIFO backed by an off chip ZBT/NoBL SRAM.
//
// This module and its sub-hierarchy implment a FIFO capable of sustaining
// a data throughput rate of at least int_clk/2 * 36bits and bursts of int_clk * 36bits.
//
// This has been designed and tested for an int_clk of 100MHz and an ext_clk of 125MHz,
// your milage may vary with other clock ratio's especially those where int_clk < ext_clk.
// Testing has also exclusively used a rst signal synchronized to int_clk.
//
// Interface operation mimics a Xilinx FIFO configured as "First Word Fall Through",
// though signal naming differs.
//
// For FPGA use registers interfacing directly with signals prefixed "RAM_*" should be
// packed into the IO ring.
//
//`define NO_EXT_FIFO
module ext_fifo
#(parameter INT_WIDTH=36,EXT_WIDTH=18,RAM_DEPTH=19,FIFO_DEPTH=19)
(
input int_clk,
input ext_clk,
input rst,
input [EXT_WIDTH-1:0] RAM_D_pi,
output [EXT_WIDTH-1:0] RAM_D_po,
output RAM_D_poe,
output [RAM_DEPTH-1:0] RAM_A,
output RAM_WEn,
output RAM_CENn,
output RAM_LDn,
output RAM_OEn,
output RAM_CE1n,
input [INT_WIDTH-1:0] datain,
input src_rdy_i, // WRITE
output dst_rdy_o, // not FULL
output [INT_WIDTH-1:0] dataout,
output src_rdy_o, // not EMPTY
input dst_rdy_i, // READ
output reg [31:0] debug
);
wire [EXT_WIDTH-1:0] write_data;
wire [EXT_WIDTH-1:0] read_data;
wire full1, empty1;
wire almost_full2, full2, empty2;
wire [INT_WIDTH-1:0] data_to_fifo;
wire [INT_WIDTH-1:0] data_from_fifo;
wire [FIFO_DEPTH-1:0] capacity;
// FIFO buffers data from UDP engine into external FIFO clock domain.
fifo_xlnx_512x36_2clk_36to18 fifo_xlnx_512x36_2clk_36to18_i1 (
.rst(rst),
.wr_clk(int_clk),
.rd_clk(ext_clk),
.din(datain), // Bus [35 : 0]
.wr_en(src_rdy_i),
.rd_en(space_avail&~empty1),
.dout(write_data), // Bus [17 : 0]
.full(full1),
.empty(empty1));
assign dst_rdy_o = ~full1;
`ifdef NO_EXT_FIFO
assign space_avail = ~full2;
assign data_avail = ~empty1;
assign read_data = write_data;
`else
// External FIFO running at ext clock rate and 18 bit width.
nobl_fifo #(.WIDTH(EXT_WIDTH),.RAM_DEPTH(RAM_DEPTH),.FIFO_DEPTH(FIFO_DEPTH))
nobl_fifo_i1
(
.clk(ext_clk),
.rst(rst),
.RAM_D_pi(RAM_D_pi),
.RAM_D_po(RAM_D_po),
.RAM_D_poe(RAM_D_poe),
.RAM_A(RAM_A),
.RAM_WEn(RAM_WEn),
.RAM_CENn(RAM_CENn),
.RAM_LDn(RAM_LDn),
.RAM_OEn(RAM_OEn),
.RAM_CE1n(RAM_CE1n),
.write_data(write_data),
.write_strobe(~empty1 ),
.space_avail(space_avail),
.read_data(read_data),
.read_strobe(~almost_full2),
.data_avail(data_avail),
.capacity(capacity)
);
`endif // !`ifdef NO_EXT_FIFO
// FIFO buffers data read from external FIFO into DSP clk domain and to TX DSP.
fifo_xlnx_512x36_2clk_18to36 fifo_xlnx_512x36_2clk_18to36_i1 (
.rst(rst),
.wr_clk(ext_clk),
.rd_clk(int_clk),
.din(read_data), // Bus [17 : 0]
.wr_en(data_avail),
.rd_en(dst_rdy_i),
.dout(dataout), // Bus [35 : 0]
.full(full2),
.prog_full(almost_full2),
.empty(empty2));
assign src_rdy_o = ~empty2;
always @ (posedge int_clk)
debug[31:16] = {12'h0,empty2,full1,dst_rdy_i,src_rdy_i };
always @ (posedge ext_clk)
debug[15:0] = {3'h0,empty1,space_avail,data_avail,full2,almost_full2,capacity[7:0] };
endmodule // ext_fifo
|
