1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
//
// FIFO backed by an off chip ZBT/NoBL SRAM.
//
// This module and its sub-hierarchy implment a FIFO capable of sustaining
// a data throughput rate of at least int_clk/2 * 36bits and bursts of int_clk * 36bits.
//
// This has been designed and tested for an int_clk of 100MHz and an ext_clk of 125MHz,
// your milage may vary with other clock ratio's especially those where int_clk < ext_clk.
// Testing has also exclusively used a rst signal synchronized to int_clk.
//
// Interface operation mimics a Xilinx FIFO configured as "First Word Fall Through",
// though signal naming differs.
//
// For FPGA use registers interfacing directly with signals prefixed "RAM_*" should be
// packed into the IO ring.
//
//`define NO_EXT_FIFO
module ext_fifo
#(parameter INT_WIDTH=36,EXT_WIDTH=18,RAM_DEPTH=19,FIFO_DEPTH=19)
(
input int_clk,
input ext_clk,
input rst,
input [EXT_WIDTH-1:0] RAM_D_pi,
output [EXT_WIDTH-1:0] RAM_D_po,
output RAM_D_poe,
output [RAM_DEPTH-1:0] RAM_A,
output RAM_WEn,
output RAM_CENn,
output RAM_LDn,
output RAM_OEn,
output RAM_CE1n,
input [INT_WIDTH-1:0] datain,
input src_rdy_i, // WRITE
output dst_rdy_o, // not FULL
output [INT_WIDTH-1:0] dataout,
output src_rdy_o, // not EMPTY
input dst_rdy_i, // READ
output reg [31:0] debug,
output reg [31:0] debug2
);
wire [EXT_WIDTH-1:0] write_data;
wire [EXT_WIDTH-1:0] read_data;
wire full1, empty1;
wire almost_full2, almost_full2_spread, full2, empty2;
wire [FIFO_DEPTH-1:0] capacity;
wire space_avail;
wire data_avail;
// These next 2 lines here purely because ICARUS is crap at handling generate statements.
// Empirically this has been determined to make simulations work.
wire read_input_fifo = space_avail & ~empty1;
wire write_output_fifo = data_avail;
assign src_rdy_o = ~empty2;
assign dst_rdy_o = ~full1;
`ifdef NO_EXT_FIFO
assign space_avail = ~full2;
assign data_avail = ~empty1;
assign read_data = write_data;
`else
// External FIFO running at ext clock rate and 18 or 36 bit width.
nobl_fifo #(.WIDTH(EXT_WIDTH),.RAM_DEPTH(RAM_DEPTH),.FIFO_DEPTH(FIFO_DEPTH))
nobl_fifo_i1
(
.clk(ext_clk),
.rst(rst),
.RAM_D_pi(RAM_D_pi),
.RAM_D_po(RAM_D_po),
.RAM_D_poe(RAM_D_poe),
.RAM_A(RAM_A),
.RAM_WEn(RAM_WEn),
.RAM_CENn(RAM_CENn),
.RAM_LDn(RAM_LDn),
.RAM_OEn(RAM_OEn),
.RAM_CE1n(RAM_CE1n),
.write_data(write_data),
.write_strobe(~empty1 ),
.space_avail(space_avail),
.read_data(read_data),
.read_strobe(~almost_full2_spread),
.data_avail(data_avail),
.capacity(capacity)
);
`endif // !`ifdef NO_EXT_FIFO
generate
if (EXT_WIDTH == 18 && INT_WIDTH == 36) begin: fifo_g1
// FIFO buffers data from UDP engine into external FIFO clock domain.
fifo_xlnx_512x36_2clk_36to18 fifo_xlnx_512x36_2clk_36to18_i1 (
.rst(rst),
.wr_clk(int_clk),
.rd_clk(ext_clk),
.din(datain), // Bus [35 : 0]
.wr_en(src_rdy_i),
.rd_en(read_input_fifo),
.dout(write_data), // Bus [17 : 0]
.full(full1),
.empty(empty1));
// FIFO buffers data read from external FIFO into DSP clk domain and to TX DSP.
fifo_xlnx_512x36_2clk_18to36 fifo_xlnx_512x36_2clk_18to36_i1 (
.rst(rst),
.wr_clk(ext_clk),
.rd_clk(int_clk),
.din(read_data), // Bus [17 : 0]
.wr_en(write_output_fifo),
.rd_en(dst_rdy_i),
.dout(dataout), // Bus [35 : 0]
.full(full2),
.prog_full(almost_full2),
.empty(empty2));
end // block: fifo_g1
else if (EXT_WIDTH == 36 && INT_WIDTH == 36) begin: fifo_g1
// FIFO buffers data from UDP engine into external FIFO clock domain.
fifo_xlnx_32x36_2clk fifo_xlnx_32x36_2clk_i1 (
.rst(rst),
.wr_clk(int_clk),
.rd_clk(ext_clk),
.din(datain), // Bus [35 : 0]
.wr_en(src_rdy_i),
.rd_en(read_input_fifo),
.dout(write_data), // Bus [35 : 0]
.full(full1),
.empty(empty1));
// FIFO buffers data read from external FIFO into DSP clk domain and to TX DSP.
fifo_xlnx_512x36_2clk_prog_full fifo_xlnx_32x36_2clk_prog_full_i1 (
.rst(rst),
.wr_clk(ext_clk),
.rd_clk(int_clk),
.din(read_data), // Bus [35 : 0]
.wr_en(write_output_fifo),
.rd_en(dst_rdy_i),
.dout(dataout), // Bus [35 : 0]
.full(full2),
.empty(empty2),
.prog_full(almost_full2));
end
endgenerate
refill_randomizer #(.BITS(7))
refill_randomizer_i1 (
.clk(ext_clk),
.rst(rst),
.full_in(almost_full2),
.full_out(almost_full2_spread)
);
// always @ (posedge int_clk)
// debug[31:28] <= {empty2,full1,dst_rdy_i,src_rdy_i };
always @ (posedge ext_clk)
// debug[27:0] <= {RAM_WEn,RAM_CE1n,RAM_A[3:0],read_data[17:0],empty1,space_avail,data_avail,almost_full2 };
debug[31:0] <= {7'h0,src_rdy_i,read_input_fifo,write_output_fifo,dst_rdy_i,full2,almost_full2,empty2,full1,empty1,write_data[7:0],read_data[7:0]};
always@ (posedge ext_clk)
// debug2[31:0] <= {write_data[15:0],read_data[15:0]};
debug2[31:0] <= 0;
endmodule // ext_fifo
|
