1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
|
========================================================================
UHD - USRP2 Application Notes
========================================================================
.. contents:: Table of Contents
------------------------------------------------------------------------
Load the images onto the SD card
------------------------------------------------------------------------
**Warning!**
Use the usrp2_card_burner.py with caution. If you specify the wrong device node,
you could overwrite your hard drive. Make sure that --dev= specifies the SD card.
**Warning!**
It is possible to use 3rd party SD cards with the USRP2.
However, certain types of SD cards will not interface with the CPLD:
* Cards can be SDHC, which is not a supported interface.
* Cards can have unexpected timing characteristics.
For these reasons, we recommend that you use the SD card that was supplied with the USRP2.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Use the card burner tool (unix)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
::
sudo <prefix>/share/uhd/utils/usrp2_card_burner_gui.py
-- OR --
cd <prefix>/share/uhd/utils
sudo ./usrp2_card_burner.py --dev=/dev/sd<XXX> --fpga=<path_to_fpga_image>
sudo ./usrp2_card_burner.py --dev=/dev/sd<XXX> --fw=<path_to_firmware_image>
Use the *--list* option to get a list of possible raw devices.
The list result will filter out disk partitions and devices too large to be the sd card.
The list option has been implemented on Linux, Mac OS X, and Windows.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Use the card burner tool (windows)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
::
<path_to_python.exe> <prefix>/share/uhd/utils/usrp2_card_burner_gui.py
------------------------------------------------------------------------
Setup networking
------------------------------------------------------------------------
The USRP2 only supports gigabit ethernet,
and will not work with a 10/100 Mbps interface.
However, a 10/100 Mbps interface can be connected indirectly
to a USRP2 through a gigabit ethernet switch.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Setup the host interface
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The USRP2 communicates at the IP/UDP layer over the gigabit ethernet.
The default IP address of the USRP2 is **192.168.10.2**
You will need to configure the host's ethernet interface with a static IP address to enable communication.
An address of **192.168.10.1** and a subnet mask of **255.255.255.0** is recommended.
**Note:**
When using the UHD, if an IP address for the USRP2 is not specified,
the software will use UDP broadcast packets to locate the USRP2.
On some systems, the firewall will block UDP broadcast packets.
It is recommended that you change or disable your firewall settings.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Multiple device configuration
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
For maximum throughput, one ethernet interface per USRP2 is recommended,
although multiple devices may be connected via a gigabit ethernet switch.
In any case, each ethernet interface should have its own subnet,
and the corresponding USRP2 device should be assigned an address in that subnet.
Example:
**Configuration for USRP2 device 0:**
* Ethernet interface IPv4 address: 192.168.10.1
* Ethernet interface subnet mask: 255.255.255.0
* USRP2 device IPv4 address: 192.168.10.2
**Configuration for USRP2 device 1:**
* Ethernet interface IPv4 address: 192.168.20.1
* Ethernet interface subnet mask: 255.255.255.0
* USRP2 device IPv4 address: 192.168.20.2
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Change the USRP2's IP address
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
You may need to change the USRP2's IP address for several reasons:
* to satisfy your particular network configuration
* to use multiple USRP2s on the same host computer
* to set a known IP address into USRP2 (in case you forgot)
**Method 1:**
To change the USRP2's IP address
you must know the current address of the USRP2,
and the network must be setup properly as described above.
Run the following commands:
::
cd <prefix>/share/uhd/utils
./usrp_burn_mb_eeprom --args=<optional device args> --key=ip-addr --val=192.168.10.3
**Method 2 (Linux Only):**
This method assumes that you do not know the IP address of your USRP2.
It uses raw ethernet packets to bypass the IP/UDP layer to communicate with the USRP2.
Run the following commands:
::
cd <prefix>/share/uhd/utils
sudo ./usrp2_recovery.py --ifc=eth0 --new-ip=192.168.10.3
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Debugging networking problems
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
**Disable the firewall:**
If uhd_find_devices gives you nothing
but uhd_find_devices --args addr=192.168.10.2 yeilds a discovered device,
then your firewall may be blocking replies to UDP broadcast packets.
**Ping the USRP2:**
The USRP2 will reply to icmp echo requests.
::
ping 192.168.10.2
**Monitor the USRP2:**
You can read the serial port on the rear of the USRP2
to get debug verbose from the embedded microcontroller.
Use a standard USB to 3.3v-level serial converter at 230400 baud.
The microcontroller prints useful information about IP addresses,
MAC addresses, control packets, and fast-path settings.
**Monitor the host network traffic:**
Use wireshark to monitor packets sent to and received from the USRP2.
------------------------------------------------------------------------
Addressing the device
------------------------------------------------------------------------
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Single device configuration
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
A USRP2 can be identified though its IPv4 address or resolvable hostname.
The USRP2 device is referenced through the "addr" key in the device address.
Use this addressing scheme with the *simple_usrp* interface.
The device address string representation for a USRP2 with IPv4 address 192.168.10.2
::
addr=192.168.10.2
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Soft-MIMO configuration
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
In a soft-mimo configuration, each USRP2 must have a unique IPv4 address (per computer)
and be attached to its own dedicated network port.
The value for the addr key is a white-space separated list
of IPv4 addresses or resolvable hostnames.
The first address in the list will represent channel 0,
the second channel 1, and so on...
Use this addressing scheme with the *multi_usrp* interface.
The device address string representation for 2 USRP2s with IPv4 addresses 192.168.10.2 and 192.168.20.2
::
addr=192.168.10.2 192.168.20.2
------------------------------------------------------------------------
Hardware setup notes
------------------------------------------------------------------------
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Front panel LEDs
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The LEDs on the front panel can be useful in debugging hardware and software issues.
The LEDs reveal the following about the state of the device:
* **LED A:** transmitting
* **LED B:** undocumented
* **LED C:** receiving
* **LED D:** firmware loaded
* **LED E:** reference lock
* **LED F:** CPLD loaded
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Ref Clock - 10MHz
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Using an external 10MHz reference clock requires a signal level between
+5dBm and +20dBm at 10MHz applied to the Ref Clock SMA port on the front panel.
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
PPS - Pulse Per Second
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Using a PPS signal for timestamp synchronization requires a 5Vpp square wave signal
Test the PPS input of the USRP2 with the following app:
::
cd <prefix>/share/uhd/examples
./test_pps_input --args=<args>
* <args> are device address arguments (optional if only one USRP is on your machine)
|
