1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
|
/*! \page page_mpm The Module Peripheral Manager (MPM) Architecture
\tableofcontents
For embedded USRP devices, there is an additional layer of control that UHD uses
to access, configure, and control the hardware: The Module Peripheral Manager
(MPM) daemon. In most cases, users of UHD do not need to know any details about
MPM, but for some advanced use cases, it can be a useful tool.
\section mpm_arch Architecture Overview
Devices built using the MPM architecture must be capable of running an embedded
Linux system. Within that system, the MPM daemon is continuously running and
will allow access to device through a network-RPC based API. The UHD session
calling into the device will thus be able to access that high-level API instead
of directly having to interact with registers or other low-level components.
This way, there is only a single driver in UHD for all MPM-powered devices.
The source code for the MPM daemon is located in the `mpm/` subdirectory of the
UHD repository (note that the UHD library's source code is located in the
`host/` subdirectory). MPM is written in Python 3, C, and C++14.
When starting a UHD session to control an MPM device, UHD will, under the hood,
first try to access MPM over a network link to gain full control of the device.
Once it has accessed MPM, it will send commands to MPM to start initializing the
device for streaming usage.
The MPM RPC connection is only used for command & control. Data is streamed over
a separate connection, directly accessing the FPGA. This combines the
flexibility of a network-RPC control with the high performance of direct
streaming access.
\section mpm_arch_claiming Device Claiming
For most functionality, only a single UHD session can control MPM at the same
time. To guarantee this, MPM implements a claiming mechanism. At the beginning
of a UHD session, UHD will attempt to claim a device, which will either fail,
or will succeed and create a \b token. This token can be used by the controlling
UHD session to access peripherals which require exclusive access. UHD needs to
re-claim the device within a certain interval to not lose access to the device.
If UHD fails to claim a device, the assumption is made that the UHD process has
terminated, and MPM will disallow further access until another, valid claim has
been made.
This is similar to the X3x0, which uses a claiming mechanism controlled by the
ZPU.
\section mpm_modes Network vs. Embedded Mode
Devices such as the N310 allow running a UHD session both on the device, as well
as off device. The former is called <em>Embedded Mode</em>, the latter <em>
Network Mode</em>.
In both cases, UHD will connect to MPM over a network socket. This allows the
usage of the exact same driver for network and embedded modes, and thus, the
same software can be compiled against UHD in both modes (keep in mind that the
embedded systems are usually not as powerful as dedicated computers, so
typically, high-performance applications will always run in network mode).
\section mpm_debug Debugging Tools
The `mpm/tools/` subdirectory provides a useful tool for debugging and
interacting with MPM called `mpm_shell.py`. It is a command line tool to
directly access MPM commands. Like MPM, it requires Python 3. It can be invoked
as follows:
$ python3 tools/mpm_shell.py [-c] ni-n3xx-ABCD123
The `-c` switch will attempt to claim the device. The only other command line
argument is a network address at which the device can be reached.
If the connection succeeds, commands can be directly entered on the command
line. MPM Shell supports tab completion and on-line help using the `?` operator:
By appending it to a command, its docstring will be displayed.
> get_clock_source?
Arguments to the commands can simply be appended to the command itself:
> set_clock_source external
Arguments can also be Python expression, if the first character after the
command itself is an `=` symbol:
> set_db_eeprom =[0, open('eeprom.dat', 'w').read()]
In this example, a list is created where the first element is a '0', and the
second element is a string, read from a binary file. The list will be expanded
to become the function arguments. In this case, the RPC call `set_db_eeprom`
must thus have 2 arguments with the appropriate argument types.
Note that MPM Shell can make use of non-standard RPC features, such as
propagation of Python exceptions, which makes it a versatile debugging tool.
\section mpm_shell_hijack Hijack Mode
In hijack mode, MPM Shell is launched after another process, such as a UHD
session, is already controlling the device. By passing the token to MPM Shell,
it can access the device and perform low-level operations on the device.
The token can be gained by scanning the log messages of the UHD session.
It can be invoked as follows:
$ python3 tools/mpm_shell.py -j $TOKEN ni-n3xx-ABCD123
*/
// vim:ft=doxygen:
|
