`timescale 1ns / 1ps
//////////////////////////////////////////////////////////////////////////////////

module u2plus
  (
   input CLK_FPGA_P, input CLK_FPGA_N,  // Diff
   
   // ADC
   input ADC_clkout_p, input ADC_clkout_n,
   input ADCA_12_p, input ADCA_12_n,
   input ADCA_10_p, input ADCA_10_n,
   input ADCA_8_p, input ADCA_8_n,
   input ADCA_6_p, input ADCA_6_n,
   input ADCA_4_p, input ADCA_4_n,
   input ADCA_2_p, input ADCA_2_n,
   input ADCA_0_p, input ADCA_0_n,
   input ADCB_12_p, input ADCB_12_n,
   input ADCB_10_p, input ADCB_10_n,
   input ADCB_8_p, input ADCB_8_n,
   input ADCB_6_p, input ADCB_6_n,
   input ADCB_4_p, input ADCB_4_n,
   input ADCB_2_p, input ADCB_2_n,
   input ADCB_0_p, input ADCB_0_n,
   
   // DAC
   output reg [15:0] DACA,
   output reg [15:0] DACB,
   input DAC_LOCK,     // unused for now
   
   // DB IO Pins
   inout [15:0] io_tx,
   inout [15:0] io_rx,

   // Misc, debug
   output [5:1] leds,  // LED4 is shared w/INIT_B
   input FPGA_RESET,
   output [1:0] debug_clk,
   output [31:0] debug,
   output [3:1] TXD, input [3:1] RXD, // UARTs
   //input [3:0] dipsw,  // Forgot DIP Switches...
   
   // Clock Gen Control
   output [1:0] clk_en,
   output [1:0] clk_sel,
   input CLK_FUNC,        // FIXME is an input to control the 9510
   input CLK_STATUS,

   inout SCL, inout SDA,   // I2C

   // PPS
   input PPS_IN, input PPS2_IN,

   // SPI
   output SEN_CLK, output SCLK_CLK, output MOSI_CLK, input MISO_CLK,
   output SEN_DAC, output SCLK_DAC, output MOSI_DAC, input MISO_DAC,
   output SEN_ADC, output SCLK_ADC, output MOSI_ADC,
   output SEN_TX_DB, output SCLK_TX_DB, output MOSI_TX_DB, input MISO_TX_DB,
   output SEN_TX_DAC, output SCLK_TX_DAC, output MOSI_TX_DAC,
   output SEN_TX_ADC, output SCLK_TX_ADC, output MOSI_TX_ADC, input MISO_TX_ADC,
   output SEN_RX_DB, output SCLK_RX_DB, output MOSI_RX_DB, input MISO_RX_DB,
   output SEN_RX_DAC, output SCLK_RX_DAC, output MOSI_RX_DAC,
   output SEN_RX_ADC, output SCLK_RX_ADC, output MOSI_RX_ADC, input MISO_RX_ADC,

   // GigE PHY
   input CLK_TO_MAC,

   output reg [7:0] GMII_TXD,
   output reg GMII_TX_EN,
   output reg GMII_TX_ER,
   output GMII_GTX_CLK,
   input GMII_TX_CLK,  // 100mbps clk

   input GMII_RX_CLK,
   input [7:0] GMII_RXD,
   input GMII_RX_DV,
   input GMII_RX_ER,
   input GMII_COL,
   input GMII_CRS,

   input PHY_INTn,   // open drain
   inout MDIO,
   output MDC,
   output PHY_RESETn,
   output ETH_LED,
   
//   input POR,
   
   // Expansion
   input exp_time_in_p, input exp_time_in_n, // Diff
   output exp_time_out_p, output exp_time_out_n, // Diff 
   input exp_user_in_p, input exp_user_in_n, // Diff
   output exp_user_out_p, output exp_user_out_n, // Diff 
   
   // SERDES
   output ser_enable,
   output ser_prbsen,
   output ser_loopen,
   output ser_rx_en,
   
   output ser_tx_clk,
   output reg [15:0] ser_t,
   output reg ser_tklsb,
   output reg ser_tkmsb,

   input ser_rx_clk,
   input [15:0] ser_r,
   input ser_rklsb,
   input ser_rkmsb,

   // SRAM
   inout [35:0] RAM_D,
   output [20:0] RAM_A,
   output [3:0] RAM_BWn,
   output RAM_ZZ,
   output RAM_LDn,
   output RAM_OEn,
   output RAM_WEn,
   output RAM_CENn,
   output RAM_CLK,
   
   // SPI Flash
   output flash_cs,
   output flash_clk,
   output flash_mosi,
   input flash_miso
   );

   wire  CLK_TO_MAC_int, CLK_TO_MAC_int2;
   IBUFG phyclk (.O(CLK_TO_MAC_int), .I(CLK_TO_MAC));
   BUFG phyclk2 (.O(CLK_TO_MAC_int2), .I(CLK_TO_MAC_int));
      
   // FPGA-specific pins connections
   wire 	clk_fpga, dsp_clk, clk_div, dcm_out, wb_clk, clock_ready;

   IBUFGDS clk_fpga_pin (.O(clk_fpga),.I(CLK_FPGA_P),.IB(CLK_FPGA_N));
   defparam 	clk_fpga_pin.IOSTANDARD = "LVPECL_25";
   
   wire 	exp_time_in;
   IBUFDS exp_time_in_pin (.O(exp_time_in),.I(exp_time_in_p),.IB(exp_time_in_n));
   defparam 	exp_time_in_pin.IOSTANDARD = "LVDS_25";
   
   wire 	exp_time_out;
   OBUFDS exp_time_out_pin (.O(exp_time_out_p),.OB(exp_time_out_n),.I(exp_time_out));
   defparam 	exp_time_out_pin.IOSTANDARD  = "LVDS_25";

   wire 	exp_user_in;
   IBUFDS exp_user_in_pin (.O(exp_user_in),.I(exp_user_in_p),.IB(exp_user_in_n));
   defparam 	exp_user_in_pin.IOSTANDARD = "LVDS_25";
   
   wire 	exp_user_out;
   OBUFDS exp_user_out_pin (.O(exp_user_out_p),.OB(exp_user_out_n),.I(exp_user_out));
   defparam 	exp_user_out_pin.IOSTANDARD  = "LVDS_25";

   reg [5:0] 	clock_ready_d;
   always @(posedge clk_fpga)
     clock_ready_d[5:0] <= {clock_ready_d[4:0],clock_ready};
   wire 	dcm_rst = ~&clock_ready_d & |clock_ready_d;

   // ADC A is inverted on the schematic to facilitate a clean layout
   //  We account for that here by inverting it
`ifdef LVDS
   wire [13:0] 	adc_a, adc_a_inv, adc_b;
   capture_ddrlvds #(.WIDTH(14)) capture_ddrlvds
     (.clk(dsp_clk), .ssclk_p(ADC_clkout_p), .ssclk_n(ADC_clkout_n), 
      .in_p({{ADCA_12_p, ADCA_10_p, ADCA_8_p, ADCA_6_p, ADCA_4_p, ADCA_2_p, ADCA_0_p},
	     {ADCB_12_p, ADCB_10_p, ADCB_8_p, ADCB_6_p, ADCB_4_p, ADCB_2_p, ADCB_0_p}}), 
      .in_n({{ADCA_12_n, ADCA_10_n, ADCA_8_n, ADCA_6_n, ADCA_4_n, ADCA_2_n, ADCA_0_n},
	     {ADCB_12_n, ADCB_10_n, ADCB_8_n, ADCB_6_n, ADCB_4_n, ADCB_2_n, ADCB_0_n}}), 
      .out({adc_a_inv,adc_b}));
   assign adc_a = ~adc_a_inv;
`else
   reg [13:0] 	adc_a, adc_b;
   always @(posedge dsp_clk)
     begin
	adc_a <= ~{ADCA_12_p,ADCA_12_n, ADCA_10_p,ADCA_10_n, ADCA_8_p,ADCA_8_n, ADCA_6_p,ADCA_6_n,
		   ADCA_4_p,ADCA_4_n, ADCA_2_p,ADCA_2_n, ADCA_0_p,ADCA_0_n };
	adc_b <= {ADCB_12_p,ADCB_12_n, ADCB_10_p,ADCB_10_n, ADCB_8_p,ADCB_8_n, ADCB_6_p,ADCB_6_n,
		   ADCB_4_p,ADCB_4_n, ADCB_2_p,ADCB_2_n, ADCB_0_p,ADCB_0_n };
     end
`endif // !`ifdef LVDS
   
   // Handle Clocks
   DCM DCM_INST (.CLKFB(dsp_clk), 
                 .CLKIN(clk_fpga), 
                 .DSSEN(0), 
                 .PSCLK(0), 
                 .PSEN(0), 
                 .PSINCDEC(0), 
                 .RST(dcm_rst), 
                 .CLKDV(clk_div), 
                 .CLKFX(), 
                 .CLKFX180(), 
                 .CLK0(dcm_out), 
                 .CLK2X(), 
                 .CLK2X180(), 
                 .CLK90(), 
                 .CLK180(), 
                 .CLK270(), 
                 .LOCKED(LOCKED_OUT), 
                 .PSDONE(), 
                 .STATUS());
   defparam DCM_INST.CLK_FEEDBACK = "1X";
   defparam DCM_INST.CLKDV_DIVIDE = 2.0;
   defparam DCM_INST.CLKFX_DIVIDE = 1;
   defparam DCM_INST.CLKFX_MULTIPLY = 4;
   defparam DCM_INST.CLKIN_DIVIDE_BY_2 = "FALSE";
   defparam DCM_INST.CLKIN_PERIOD = 10.000;
   defparam DCM_INST.CLKOUT_PHASE_SHIFT = "NONE";
   defparam DCM_INST.DESKEW_ADJUST = "SYSTEM_SYNCHRONOUS";
   defparam DCM_INST.DFS_FREQUENCY_MODE = "LOW";
   defparam DCM_INST.DLL_FREQUENCY_MODE = "LOW";
   defparam DCM_INST.DUTY_CYCLE_CORRECTION = "TRUE";
   defparam DCM_INST.FACTORY_JF = 16'h8080;
   defparam DCM_INST.PHASE_SHIFT = 0;
   defparam DCM_INST.STARTUP_WAIT = "FALSE";

   BUFG dspclk_BUFG (.I(dcm_out), .O(dsp_clk));
   BUFG wbclk_BUFG (.I(clk_div), .O(wb_clk));

   // I2C -- Don't use external transistors for open drain, the FPGA implements this
   IOBUF scl_pin(.O(scl_pad_i), .IO(SCL), .I(scl_pad_o), .T(scl_pad_oen_o));
   IOBUF sda_pin(.O(sda_pad_i), .IO(SDA), .I(sda_pad_o), .T(sda_pad_oen_o));

   // LEDs are active low outputs
   wire [5:0] leds_int;
   assign     {ETH_LED,leds} = {6'b011111 ^ leds_int};  // drive low to turn on leds
   
   // SPI
   wire       miso, mosi, sclk;

   assign 	{SCLK_CLK,MOSI_CLK} 	   = ~SEN_CLK ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_DAC,MOSI_DAC} 	   = ~SEN_DAC ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_ADC,MOSI_ADC} 	   = ~SEN_ADC ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_TX_DB,MOSI_TX_DB}    = ~SEN_TX_DB ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_TX_DAC,MOSI_TX_DAC}  = ~SEN_TX_DAC ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_TX_ADC,MOSI_TX_ADC}  = ~SEN_TX_ADC ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_RX_DB,MOSI_RX_DB}    = ~SEN_RX_DB ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_RX_DAC,MOSI_RX_DAC}  = ~SEN_RX_DAC ? {sclk,mosi} : 2'B0;
   assign 	{SCLK_RX_ADC,MOSI_RX_ADC}  = ~SEN_RX_ADC ? {sclk,mosi} : 2'B0;
   
   assign 	miso 			   = (~SEN_CLK & MISO_CLK) | (~SEN_DAC & MISO_DAC) |
					     (~SEN_TX_DB & MISO_TX_DB) | (~SEN_TX_ADC & MISO_TX_ADC) |
					     (~SEN_RX_DB & MISO_RX_DB) | (~SEN_RX_ADC & MISO_RX_ADC);
   
   wire 	GMII_TX_EN_unreg, GMII_TX_ER_unreg;
   wire [7:0] 	GMII_TXD_unreg;
   wire 	GMII_GTX_CLK_int;
   
   always @(posedge GMII_GTX_CLK_int)
     begin
	GMII_TX_EN <= GMII_TX_EN_unreg;
	GMII_TX_ER <= GMII_TX_ER_unreg;
	GMII_TXD <= GMII_TXD_unreg;
     end

   OFDDRRSE OFDDRRSE_gmii_inst 
     (.Q(GMII_GTX_CLK),      // Data output (connect directly to top-level port)
      .C0(GMII_GTX_CLK_int),    // 0 degree clock input
      .C1(~GMII_GTX_CLK_int),    // 180 degree clock input
      .CE(1),    // Clock enable input
      .D0(0),    // Posedge data input
      .D1(1),    // Negedge data input
      .R(0),      // Synchronous reset input
      .S(0)       // Synchronous preset input
      );
   
   wire ser_tklsb_unreg, ser_tkmsb_unreg;
   wire [15:0] ser_t_unreg;
   wire        ser_tx_clk_int;
   
   always @(posedge ser_tx_clk_int)
     begin
	ser_tklsb <= ser_tklsb_unreg;
	ser_tkmsb <= ser_tkmsb_unreg;
	ser_t <= ser_t_unreg;
     end

   assign ser_tx_clk = clk_fpga;

   reg [15:0] ser_r_int;
   reg 	      ser_rklsb_int, ser_rkmsb_int;

   always @(posedge ser_rx_clk)
     begin
	ser_r_int <= ser_r;
	ser_rklsb_int <= ser_rklsb;
	ser_rkmsb_int <= ser_rkmsb;
     end
   
   /*
   OFDDRRSE OFDDRRSE_serdes_inst 
     (.Q(ser_tx_clk),      // Data output (connect directly to top-level port)
      .C0(ser_tx_clk_int),    // 0 degree clock input
      .C1(~ser_tx_clk_int),    // 180 degree clock input
      .CE(1),    // Clock enable input
      .D0(0),    // Posedge data input
      .D1(1),    // Negedge data input
      .R(0),      // Synchronous reset input
      .S(0)       // Synchronous preset input
      );
   */
   
   wire [15:0] dac_a_int, dac_b_int;
   // DAC A and B are swapped in schematic to facilitate clean layout
   // DAC A is also inverted in schematic to facilitate clean layout
   always @(negedge dsp_clk) DACA <= ~dac_b_int;
   always @(negedge dsp_clk) DACB <= dac_a_int;
   
   u2plus_core u2p_c(.dsp_clk           (dsp_clk),
		     .wb_clk            (wb_clk),
		     .clock_ready       (clock_ready),
		     .clk_to_mac	(CLK_TO_MAC_int2),
		     .pps_in		(PPS_IN),
		     .leds		(leds_int),
		     .debug		(debug[31:0]),
		     .debug_clk		(debug_clk[1:0]),
		     .exp_pps_in	(exp_time_in),
		     .exp_pps_out	(exp_time_out),
		     .GMII_COL		(GMII_COL),
		     .GMII_CRS		(GMII_CRS),
		     .GMII_TXD		(GMII_TXD_unreg[7:0]),
		     .GMII_TX_EN	(GMII_TX_EN_unreg),
		     .GMII_TX_ER	(GMII_TX_ER_unreg),
		     .GMII_GTX_CLK	(GMII_GTX_CLK_int),
		     .GMII_TX_CLK	(GMII_TX_CLK),
		     .GMII_RXD		(GMII_RXD[7:0]),
		     .GMII_RX_CLK	(GMII_RX_CLK),
		     .GMII_RX_DV	(GMII_RX_DV),
		     .GMII_RX_ER	(GMII_RX_ER),
		     .MDIO		(MDIO),
		     .MDC		(MDC),
		     .PHY_INTn		(PHY_INTn),
		     .PHY_RESETn	(PHY_RESETn),
		     .ser_enable	(ser_enable),
		     .ser_prbsen	(ser_prbsen),
		     .ser_loopen	(ser_loopen),
		     .ser_rx_en		(ser_rx_en),
		     .ser_tx_clk	(ser_tx_clk_int),
		     .ser_t		(ser_t_unreg[15:0]),
		     .ser_tklsb		(ser_tklsb_unreg),
		     .ser_tkmsb		(ser_tkmsb_unreg),
		     .ser_rx_clk	(ser_rx_clk),
		     .ser_r		(ser_r_int[15:0]),
		     .ser_rklsb		(ser_rklsb_int),
		     .ser_rkmsb		(ser_rkmsb_int),
		     .adc_a		(adc_a[13:0]),
		     .adc_ovf_a		(1'b0),
		     .adc_on_a		(),
		     .adc_oe_a		(),
		     .adc_b		(adc_b[13:0]),
		     .adc_ovf_b		(1'b0),
		     .adc_on_b		(),
		     .adc_oe_b		(),
		     .dac_a		(dac_a_int[15:0]),
		     .dac_b		(dac_b_int[15:0]),
		     .scl_pad_i		(scl_pad_i),
		     .scl_pad_o		(scl_pad_o),
		     .scl_pad_oen_o	(scl_pad_oen_o),
		     .sda_pad_i		(sda_pad_i),
		     .sda_pad_o		(sda_pad_o),
		     .sda_pad_oen_o	(sda_pad_oen_o),
		     .clk_en		(clk_en[1:0]),
		     .clk_sel		(clk_sel[1:0]),
		     .clk_func		(clk_func),
		     .clk_status	(clk_status),
		     .sclk		(sclk),
		     .mosi		(mosi),
		     .miso		(miso),
		     .sen_clk		(SEN_CLK),
		     .sen_dac		(SEN_DAC),
		     .sen_adc           (SEN_ADC),
		     .sen_tx_db		(SEN_TX_DB),
		     .sen_tx_adc	(SEN_TX_ADC),
		     .sen_tx_dac	(SEN_TX_DAC),
		     .sen_rx_db		(SEN_RX_DB),
		     .sen_rx_adc	(SEN_RX_ADC),
		     .sen_rx_dac	(SEN_RX_DAC),
		     .io_tx		(io_tx[15:0]),
		     .io_rx		(io_rx[15:0]),
		     .RAM_D             (RAM_D),
		     .RAM_A             (RAM_A),
		     .RAM_CE1n          (RAM_CE1n),
		     .RAM_CENn          (RAM_CENn),
		     .RAM_CLK           (RAM_CLK),
		     .RAM_WEn           (RAM_WEn),
		     .RAM_OEn           (RAM_OEn),
		     .RAM_LDn           (RAM_LDn), 
		     .uart_tx_o         (TXD[3:1]),
		     .uart_rx_i         ({1'b1,RXD[3:1]}),
		     .uart_baud_o       (),
		     .sim_mode          (1'b0),
		     .clock_divider     (2),
		     .button            (FPGA_RESET),
		     .spiflash_cs       (flash_cs),
		     .spiflash_clk      (flash_clk),
		     .spiflash_miso     (flash_miso),
		     .spiflash_mosi     (flash_mosi)
		     );

   assign RAM_ZZ = 1;
   assign RAM_BWn = 4'b1111;
   
endmodule // u2plus