/*! \page page_multiple Multiple USRP configurations

\tableofcontents

\section multiple_intro Introduction

Some USRP devices are capable of being grouped to form a single, virtual device.
A single uhd::usrp::multi_usrp instantiation can control such a compound of devices.

Currently, the following devices support this capability:

- USRP2 / N2x0 Series
- X3x0 Series
- N3x0 Series
- X4x0 Series

Note that only USRPs of the same type can be combined.

\section multiple_setup Setting up devices

A description of a multiple-USRP setup can be found on the respective device's manual pages.

Addressing of a compound of devices is done by listing multiple addresses, e.g.:

    addr0=192.168.10.2,addr1=192.168.20.2

\section multiple_channumbers Channel and Device Numbering

Assume we have combined 2 X310 USRPs into a single multi_usrp using the address string
given above, maybe using the following command:

\code{.cpp}
uhd::device_addr_t args("addr0=192.168.10.2,addr1=192.168.20.2");
uhd::usrp::multi_usrp::sptr usrp = uhd::usrp::multi_usrp::make(args);
\endcode
Some uhd::usrp::multi_usrp commands require passing a device index. This is simply
the index in the address list, so say we want to check the master clock rate on both
devices, this would be valid:
\code{.cpp}
double mcr0 = usrp->get_master_clock_rate(0);
double mcr1 = usrp->get_master_clock_rate(1);
\endcode

Some methods default to applying to all devices, so the following command
would set the time on all devices to zero:
\code{.cpp}
usrp->set_time_next_pps(uhd::time_spec_t(0));
\endcode

So, device indexes run from 0 to N-1 where N is the number of devices.

Channels are indexed in a similar way. Channel indexes run from 0 to M-1 where
M is the total number of channels on all devices.

The number and order of channels per device depends on the subdev spec (see
also \ref config_subdev). In the current example, assume all the X310 USRPs
are using their standard configuration, and all have two daughterboards inside.

In this case channels 0 and 1 map to slot A and B of the first USRP, respectively.
Channels 2 and 3 map to slots A and B of the second USRP, and so on.

However, by changing the subdev spec on individual devices, this can change.
Say we have this unusual piece of code next:

\code{.cpp}
usrp->set_rx_subdev_spec("A:0 B:0", 0);
usrp->set_rx_subdev_spec("A:0", 1);
usrp->set_rx_subdev_spec("B:0 A:0", 2);
\endcode

The first device uses the default configuration. The second device artificially
disables slot B, giving this USRP a single channel only. The third device uses
both devices, but flips their order.

Now, there's a total of 5 channels, mapped as:
- Channel 0: Slot A of Device 0
- Channel 1: Slot B of Device 0
- Channel 2: Slot A of Device 1
- Channel 3: Slot A of Device 2
- Channel 4: Slot B of Device 2

While valid, this kind of configuration is not recommended unless heavily
documented. It is usually simplest to call `set_rx_subdev_spec()` without
a device index, which will set the same subdev spec on all devices.
This assumes all devices have a similar daughterboard configuration

\section multiple_mimo MIMO Operation

When a multi-channel streamer is generated from a compound multi_usrp, and
a streamer with multiple channels is generated, MIMO operations is automatically
chosen. This means samples will be aligned between streams automatically.

In order for this to work, all devices must use a common time and frequency
reference. This can be achieved in different ways, e.g. by daisy-chaining
devices (for a small number of X-Series devices), using the MIMO cable (when
only 2 N2x0 devices are used), or using a clock distribution system, e.g. an
OctoClock. See \ref page_sync and the individual device manuals on more details
on how to do this.

*/
// vim:ft=doxygen: