/*! \page page_configuration Configuring Devices and Streamers \section config_devaddr Device Configuration through address string The address string for a device is mainly used to identify a device (see also \ref page_identification), but it can also be used to propagate settings to the device. As an example, say you run `rx_samples_to_file` with the following settings: $ rx_samples_to_file --args type=b200,master_clock_rate=16e6 This will first use the `type` flag to search your system for connected B200 or B210 devices, as described on \ref page_identification. Once it has found one of these, it will connect to it and pass the `master_clock_rate=16e6` option to the device initialization (in this case, it will set the master clock rate to 16 MHz as described on \ref b200_mcr). The following table lists the configuration options you can pass as device arguments. Also check out the individual device manuals for more information and possible more options. Key | Description | Supported Devices | Example Value ---------------------|------------------------------------------------------------------------------|-------------------|--------------------- blank_eeprom | *Caution!* Having this key will erase the EEPROM and can damage your device! | X3x0 | blank_eeprom=1 fpga | Provide alternative FPGA bitfile | All USB Devices, X3x0 (PCIe only), E310, E1x0 | fpga=/path/to/bitfile.bit fw | Provide alternative firmware | All USB Devices, X3x0 | fw=/path/to/fw.bin ignore-cal-file | Ignores existing device calibration files | All Devices with cal-file support| See \ref ignore_cal_file master_clock_rate | Master Clock Rate in Hz | X3x0, B2x0, B1x0, E3x0, E1x0, N3xx | master_clock_rate=16e6 dboard_clock_rate | Daughterboard clock rate in Hz | X3x0 | dboard_clock_rate=50e6 system_ref_rate | Frequency of external reference | X3x0 | system_ref_rate=11.52e6 mcr | Override master clock rate settings (see \ref usrp1_hw_extclk) | USRP1 | mcr=52e6 niusrprpc_port | RPC Port for NI USRP RIO | X3x0 | niusrprpc_port=5445 system_ref_rate | Reference Clock Rate in Hz | X3x0 | system_ref_rate=10e6 self_cal_adc_delay | Run ADC transfer delay self-calibration. | X3x0 | self_cal_adc_delay=1 ext_adc_self_test | Run an extended ADC self test (more than the usual) | X3x0 | ext_adc_self_test=1 recover_mb_eeprom | Disable version checks. Can damage hardware. Only recommended for recovering devices with corrupted EEPROMs. | X3x0, N230 | recover_mb_eeprom=1 skip_dram | Ignore DRAM FIFO block. Connect TX streamers straight into DUC or radio. | X3x0, N3x0 | skip_dram=1 skip_ddc | Ignore DDC block. Connect Rx streamers straight into radio. | X3x0, N3x0 | skip_ddc=1 skip_duc | Ignore DUC block. Connect Rx streamers or DRAM straight into radio. | X3x0, N3x0 | skip_duc=1 In addition, many of the streaming-related options can be set per-device at configuration time. See \ref config_stream_args and \ref page_transport for more details. \section config_subdev Specifying the Subdevice A subdevice specification (or "subdev spec") string for USRP family devices is composed of: : Ex: The subdev spec markup string to select a WBX on slot B. B:0 Ex: The subdev spec markup string to select a BasicRX on slot B. B:AB -- OR -- B:A -- OR -- B:B A subdev spec can consist of multiple strings if a motherboard has the option for more than one radio device. In the X300, you may have an SBX in slot A and a CBX in slot B. Both of these daughterboards have one frontend ("0"), so the subdev spec to configure both these radio channels would look like this: A:0 B:0 The individual subdev specs are separated by spaces. On some devices, such as the X300 or the B200, it is possible to swap these to hint that slot B should be the first radio ("channel 0") and slot A should be the second radio ("channel 1"): B:0 A:0 On devices with more than one radio, setting the subdev spec to a single value declares that the other radio is not used. In a configuration with multiple USRPs, this means that this device will only be assigned a single channel. Note that a subdev spec string always only pertains to a *single* USRP, even if multiple USRPs are configured to run together. For such a configuration, you set a subdev spec string for every device individually. \subsection config_subdev_slotnames USRP Family Motherboard Slot Names All USRP family motherboards have a first slot named **A:**. The USRP1 and X3x0 have two daughterboard subdevice slots, known as **A:** and **B:**. The B210 and E310 series have a different configuration, since their two radios are logically connected to the same "daughterboard" (which is in reality the integrated AD9361), but different frontends. To select both radios on a B200 or an E300, use this string: A:A A:B \subsection config_subdev_default USRP Family Motherboard Slot Names \subsection config_subdev_dbnames Daughterboard Frontend Names Daughterboard frontend names can be used to specify which signal path is used from a daughterboard. Most daughterboards have only one frontend `:0`. A few daughterboards (Basic, LF and TVRX2) have multiple frontend names available. The frontend names are documented in \ref page_dboards. \section config_stream_args Streaming Arguments (Stream Args) When initializing a streamer using uhd::device::get_tx_stream() and/or uhd::device::get_rx_stream(), you must specify a uhd::stream_args_t object (see the manual for this struct and an in-depth explanation of the individual components). */ // vim:ft=doxygen: