/////////////////////////////////// // // NOTE: A set of precompiler directives configure the features in an FPGA build // and are listed here. These should be set exclusively using the Makefile mechanism provided. // // ETH10G_PORT0 - Ethernet Port0 is configured for 10G (default is 1G) // ETH10G_PORT1 - Ethernet Port1 is configured for 10G (default is 1G) // NO_DRAM_FIFOS - All DRAM I/F logic, supporting AXI4 and VFIFOs' replaced by internal SRAM FIFOs. // DELETE_DSP0 - Deletes DUC and DDC from Radio0 // DELETE_DSP1 - Deletes DUC and DDC from Radio1 // DEBUG_UART - Adds 115kbaud UART to GPIO pins 10 & 11 for firmware debug // /////////////////////////////////// //Defines `LVFPGA_IFACE constants `include "../../lib/io_port2/LvFpga_Chinch_Interface.vh" module x300 ( /////////////////////////////////// // // Clock sources for main FPGA clocks // /////////////////////////////////// input FPGA_CLK_p, input FPGA_CLK_n, input FPGA_125MHz_CLK, /////////////////////////////////// // // High Speed SPF+ signals and clocking // /////////////////////////////////// `ifdef BUILD_1G input ETH_CLK_p, input ETH_CLK_n, `endif `ifdef BUILD_10G input XG_CLK_p, input XG_CLK_n, `endif input SFP0_RX_p, input SFP0_RX_n, output SFP0_TX_p, output SFP0_TX_n, input SFP1_RX_p, input SFP1_RX_n, output SFP1_TX_p, output SFP1_TX_n, /////////////////////////////////// // // DRAM Interface // /////////////////////////////////// `ifndef NO_DRAM_FIFOS inout [31:0] ddr3_dq, // Data pins. Input for Reads, Output for Writes. inout [3:0] ddr3_dqs_n, // Data Strobes. Input for Reads, Output for Writes. inout [3:0] ddr3_dqs_p, // output [14:0] ddr3_addr, // Address output [2:0] ddr3_ba, // Bank Address output ddr3_ras_n, // Row Address Strobe. output ddr3_cas_n, // Column address select output ddr3_we_n, // Write Enable output ddr3_reset_n, // SDRAM reset pin. output [0:0] ddr3_ck_p, // Differential clock output [0:0] ddr3_ck_n, output [0:0] ddr3_cke, // Clock Enable output [0:0] ddr3_cs_n, // Chip Select output [3:0] ddr3_dm, // Data Mask [3] = UDM.U26, [2] = LDM.U26, ... output [0:0] ddr3_odt, // On-Die termination enable. // input sys_clk_i, // 100MHz clock source to generate DDR3 clocking. `endif /////////////////////////////////// // // IOPORT2 // /////////////////////////////////// //-- The IO_Port2 asynchronous handshaking pins input aIoResetIn_n, output aIoReadyOut, input aIoReadyIn, output aIoPort2Restart, input aStc3Gpio7, //-- The IO_Port2 high speed receiver pins input IoRxClock, input IoRxClock_n, input [15:0] irIoRxData, input [15:0] irIoRxData_n, input irIoRxHeader, input irIoRxHeader_n, //-- The IO_Port2 high speed transmitter interface pins output IoTxClock, output IoTxClock_n, output [15:0] itIoTxData, output [15:0] itIoTxData_n, output itIoTxHeader, output itIoTxHeader_n, output aIrq, /////////////////////////////////// // // ADC and DAC interfaces // /////////////////////////////////// input DB0_ADC_DCLK_P, input DB0_ADC_DCLK_N, input DB0_ADC_DA0_P, input DB0_ADC_DA0_N, input DB0_ADC_DB0_P, input DB0_ADC_DB0_N, input DB0_ADC_DA1_P, input DB0_ADC_DA1_N, input DB0_ADC_DB1_P, input DB0_ADC_DB1_N, input DB0_ADC_DA2_P, input DB0_ADC_DA2_N, input DB0_ADC_DB2_P, input DB0_ADC_DB2_N, input DB0_ADC_DA3_P, input DB0_ADC_DA3_N, input DB0_ADC_DB3_P, input DB0_ADC_DB3_N, input DB0_ADC_DA4_P, input DB0_ADC_DA4_N, input DB0_ADC_DB4_P, input DB0_ADC_DB4_N, input DB0_ADC_DA5_P, input DB0_ADC_DA5_N, input DB0_ADC_DB5_P, input DB0_ADC_DB5_N, input DB0_ADC_DA6_P, input DB0_ADC_DA6_N, input DB0_ADC_DB6_P, input DB0_ADC_DB6_N, input DB1_ADC_DCLK_P, input DB1_ADC_DCLK_N, input DB1_ADC_DA0_P, input DB1_ADC_DA0_N, input DB1_ADC_DB0_P, input DB1_ADC_DB0_N, input DB1_ADC_DA1_P, input DB1_ADC_DA1_N, input DB1_ADC_DB1_P, input DB1_ADC_DB1_N, input DB1_ADC_DA2_P, input DB1_ADC_DA2_N, input DB1_ADC_DB2_P, input DB1_ADC_DB2_N, input DB1_ADC_DA3_P, input DB1_ADC_DA3_N, input DB1_ADC_DB3_P, input DB1_ADC_DB3_N, input DB1_ADC_DA4_P, input DB1_ADC_DA4_N, input DB1_ADC_DB4_P, input DB1_ADC_DB4_N, input DB1_ADC_DA5_P, input DB1_ADC_DA5_N, input DB1_ADC_DB5_P, input DB1_ADC_DB5_N, input DB1_ADC_DA6_P, input DB1_ADC_DA6_N, input DB1_ADC_DB6_P, input DB1_ADC_DB6_N, output DB0_DAC_DCI_P, output DB0_DAC_DCI_N, output DB0_DAC_FRAME_P, output DB0_DAC_FRAME_N, output DB0_DAC_D0_P, output DB0_DAC_D0_N, output DB0_DAC_D1_P, output DB0_DAC_D1_N, output DB0_DAC_D2_P, output DB0_DAC_D2_N, output DB0_DAC_D3_P, output DB0_DAC_D3_N, output DB0_DAC_D4_P, output DB0_DAC_D4_N, output DB0_DAC_D5_P, output DB0_DAC_D5_N, output DB0_DAC_D6_P, output DB0_DAC_D6_N, output DB0_DAC_D7_P, output DB0_DAC_D7_N, output DB0_DAC_ENABLE, output DB1_DAC_DCI_P, output DB1_DAC_DCI_N, output DB1_DAC_FRAME_P, output DB1_DAC_FRAME_N, output DB1_DAC_D0_P, output DB1_DAC_D0_N, output DB1_DAC_D1_P, output DB1_DAC_D1_N, output DB1_DAC_D2_P, output DB1_DAC_D2_N, output DB1_DAC_D3_P, output DB1_DAC_D3_N, output DB1_DAC_D4_P, output DB1_DAC_D4_N, output DB1_DAC_D5_P, output DB1_DAC_D5_N, output DB1_DAC_D6_P, output DB1_DAC_D6_N, output DB1_DAC_D7_P, output DB1_DAC_D7_N, output DB1_DAC_ENABLE, output DB0_SCLK, output DB0_MOSI, output DB0_ADC_SEN, output DB0_DAC_SEN, output DB0_TX_SEN, output DB0_RX_SEN, output DB0_RX_LSADC_SEN, output DB0_RX_LSDAC_SEN, output DB0_TX_LSADC_SEN, output DB0_TX_LSDAC_SEN, input DB0_RX_LSADC_MISO, input DB0_RX_MISO, input DB0_TX_LSADC_MISO, input DB0_TX_MISO, output DB1_SCLK, output DB1_MOSI, output DB1_ADC_SEN, output DB1_DAC_SEN, output DB1_TX_SEN, output DB1_RX_SEN, output DB1_RX_LSADC_SEN, output DB1_RX_LSDAC_SEN, output DB1_TX_LSADC_SEN, output DB1_TX_LSDAC_SEN, input DB1_RX_LSADC_MISO, input DB1_RX_MISO, input DB1_TX_LSADC_MISO, input DB1_TX_MISO, output DB_DAC_SCLK, inout DB_DAC_MOSI, output DB_ADC_RESET, output DB_DAC_RESET, inout DB_SCL, inout DB_SDA, /////////////////////////////////// // // GPIO/LEDS/Etc // /////////////////////////////////// inout [11:0] FrontPanelGpio, output LED_ACT1, output LED_ACT2, output LED_LINK1, output LED_LINK2, output LED_PPS, output LED_REFLOCK, output LED_GPSLOCK, output LED_LINKSTAT, output LED_LINKACT, output LED_RX1_RX, output LED_RX2_RX, output LED_TXRX1_RX, output LED_TXRX1_TX, output LED_TXRX2_RX, output LED_TXRX2_TX, inout [15:0] DB0_TX_IO, inout [15:0] DB0_RX_IO, inout [15:0] DB1_TX_IO, inout [15:0] DB1_RX_IO, /////////////////////////////////// // // LMK CLock chip // /////////////////////////////////// input [1:0] LMK_Status, input LMK_Holdover, input LMK_Lock, input LMK_Sync, //not used, we do soft sync output LMK_SEN, output LMK_MOSI, output LMK_SCLK, /////////////////////////////////// // // GPSDO and Clock Refs // /////////////////////////////////// output [1:0] ClockRefSelect, output GPS_SER_IN, input GPS_SER_OUT, input GPS_PPS_OUT, input EXT_PPS_IN, output EXT_PPS_OUT, input GPS_LOCK_OK, output GPSDO_PWR_ENA, output TCXO_ENA, output CPRI_CLK_OUT_P, output CPRI_CLK_OUT_N, input FPGA_REFCLK_10MHz_p, input FPGA_REFCLK_10MHz_n, /////////////////////////////////// // // Supporting I/O for SPF+ interfaces // (non high speed stuff) // /////////////////////////////////// inout SFPP0_SCL, inout SFPP0_SDA, input SFPP0_ModAbs, input SFPP0_RxLOS, // High if module asserts Loss of Signal input SFPP0_TxFault, // Current 10G PMA/PCS apparently ignores this signal. output SFPP0_RS0, // These are actually open drain outputs output SFPP0_RS1, // CAUTION! Take great care, this signal shorted to VeeR on SFP module. output SFPP0_TxDisable, // These are actually open drain outputs inout SFPP1_SCL, inout SFPP1_SDA, input SFPP1_ModAbs, input SFPP1_RxLOS, // High if module asserts Loss of Signal input SFPP1_TxFault, // Current 10G PMA/PCS apparently ignores this signal. output SFPP1_RS0, // These are actually open drain outputs output SFPP1_RS1, // CAUTION! Take great care, this signal shorted to VeeR on SFP module. output SFPP1_TxDisable // These are actually open drain outputs ); // // LOG2 function. // function integer clogb2 (input integer size); begin size = size - 1; for (clogb2=1; size>1; clogb2=clogb2+1) size = size >> 1; end endfunction // clogb2 wire radio_clk, radio_clk_2x; wire global_rst, radio_rst, bus_rst; wire [3:0] sw_rst; wire [63:0] vita_time; wire [2:0] led0, led1; wire [31:0] debug0, debug1; ///////////////////////////////////////////////////////////////////// // // Debug logic on front panel GPIO pins // ////////////////////////////////////////////////////////////////////// wire debug_txd, debug_rxd; `ifdef DEBUG_UART assign FrontPanelGpio[11] = debug_txd; assign debug_rxd = FrontPanelGpio[10]; `endif //////////////////////////////////////////////////////////////////// // // Generate Bus Clock and PCIe Clocks. // Source clock comes from U19 which is fixed freq // and bufferd to be used by STC3 also (Page17 schematics). // //////////////////////////////////////////////////////////////////// wire fpga_clk125, bus_clk, ioport2_clk, rio40_clk, ioport2_idelay_ref_clk; wire bus_clk_locked, rio40_clk_locked, rio40_clk_reset; IBUFG fpga_125MHz_clk_buf ( .I(FPGA_125MHz_CLK), .O(fpga_clk125)); bus_clk_gen bus_clk_gen ( .CLK_IN1(fpga_clk125), //Input Clock: 125MHz Clock from STC3 .CLK_OUT1(bus_clk), //Output Clock 1: 175MHz .CLK_OUT2(ioport2_clk), //Output Clock 2: 125MHz .RESET(1'b0), .LOCKED(bus_clk_locked)); //rio40_clk and ioport2_idelay_ref_clk cannot share a PLL/MMCM reset with ioport2_clk //so they have to come from a different clocking primitive instance pcie_clk_gen pcie_clk_gen ( .CLK_IN1(fpga_clk125), //Input Clock: 125MHz Clock from STC3 .CLK_OUT1(rio40_clk), //Output Clock 1: 40MHz .CLK_OUT2(ioport2_idelay_ref_clk), //Output Clock 2: 200MHz .RESET(rio40_clk_reset), .LOCKED(rio40_clk_locked)); ///////////////////////////////////////////////////////////////////// // // 10MHz Reference clock // ////////////////////////////////////////////////////////////////////// wire ref_clk_10mhz; IBUFDS IBUFDS_10_MHz ( .O(ref_clk_10mhz), .I(FPGA_REFCLK_10MHz_p), .IB(FPGA_REFCLK_10MHz_n) ); ////////////////////////////////////////////////////////////////////// // CPRI Clock output -- this is the dirty recovered clock from the MGT // This goes to the LMK04816 which locks to it and cleans it up // We get the clean versions back as CPRI_CLK (for the CPRI MGT) // and FPGA_CLK (for our main rfclk) ////////////////////////////////////////////////////////////////////// wire cpri_clk_out = 1'b0; // FIXME - connect to CPRI clock recovery when implemented OBUFDS OBUFDS_cpri (.I(cpri_clk_out), .O(CPRI_CLK_OUT_P), .OB(CPRI_CLK_OUT_N)); ///////////////////////////////////////////////////////////////////// // // power-on-reset logic. // ////////////////////////////////////////////////////////////////////// por_gen por_gen(.clk(bus_clk), .reset_out(global_rst)); ////////////////////////////////////////////////////////////////////// wire sync_dacs_radio0, sync_dacs_radio1; wire [31:0] rx0, rx1; wire [31:0] tx0, tx1; wire sclk0, mosi0, miso0, sclk1, mosi1, miso1; wire [7:0] sen0, sen1; wire set_stb; wire [7:0] set_addr; wire [31:0] set_data; //////////////////////////////////////////////////////////////////// // // Generate Radio Clocks from LMK04816 // Radio clock is normally 200MHz, radio_clk_2x 400MHz. // In CPRI or LTE mode, radio clock is 184.32 MHz. // radio_clk_2x is only to be used for clocking out TX samples to DAC // //////////////////////////////////////////////////////////////////// wire radio_clk_locked; radio_clk_gen radio_clk_gen (.CLK_IN1_P(FPGA_CLK_p), .CLK_IN1_N(FPGA_CLK_n), .CLK_OUT1(radio_clk), .CLK_OUT2(radio_clk_2x), .RESET(sw_rst[2]), .LOCKED(radio_clk_locked)); defparam radio_clk_gen.clkin1_buf.DIFF_TERM = "TRUE"; //////////////////////////////////////////////////////////////////// // // IJB. Radio PLL doesn't seem to lock at power up. // Probably needs AD9610 to be programmed to 120 or 200MHz to get // an input clock thats in the ball park for PLL configuration. // Currently use busclk PLL lock signal to control this reset, // but we should find a better solution, perhaps a S/W controllable // reset like the ETH PHY uses so that we can reset this clock domain // after programming the AD9610. // //////////////////////////////////////////////////////////////////// reset_sync radio_reset_sync ( .clk(radio_clk), .reset_in(global_rst || !bus_clk_locked || sw_rst[1]), .reset_out(radio_rst) ); reset_sync int_reset_sync ( .clk(bus_clk), .reset_in(global_rst || !bus_clk_locked), .reset_out(bus_rst) ); //////////////////////////////////////////////////////////////////// // PPS // Support for internal, external, and GPSDO PPS inputs // Every attempt to minimize propagation between the external PPS // input and outputs to support daisy-chaining the signal. //////////////////////////////////////////////////////////////////// // Generate an internal PPS signal with a 25% duty cycle reg [31:0] pps_count; wire int_pps = (pps_count < 32'd2500000); always @(posedge ref_clk_10mhz) begin if (pps_count >= 32'd9999999) pps_count <= 32'b0; else pps_count <= pps_count + 1'b1; end // PPS MUX - selects internal, external, or gpsdo PPS reg pps; wire [1:0] pps_select; wire pps_out_enb; always @(*) begin case(pps_select) 2'b00 : pps = EXT_PPS_IN; 2'b01 : pps = 1'b0; 2'b10 : pps = int_pps; 2'b11 : pps = GPS_PPS_OUT; default: pps = 1'b0; endcase end // PPS out and LED assign EXT_PPS_OUT = pps & pps_out_enb; assign LED_PPS = ~pps; // active low LED driver assign LED_GPSLOCK = ~GPS_LOCK_OK; assign LED_REFLOCK = ~LMK_Lock; assign {LED_RX1_RX,LED_TXRX1_TX,LED_TXRX1_RX} = ~led0; // active low LED driver assign {LED_RX2_RX,LED_TXRX2_TX,LED_TXRX2_RX} = ~led1; // active low LED driver // Allocate SPI chip selects to various slaves. assign {DB1_DAC_SEN, DB1_ADC_SEN, DB1_RX_LSADC_SEN, DB1_RX_LSDAC_SEN, DB1_TX_LSADC_SEN, DB1_TX_LSDAC_SEN, DB1_RX_SEN, DB1_TX_SEN} = sen1; assign {DB0_DAC_SEN, DB0_ADC_SEN, DB0_RX_LSADC_SEN, DB0_RX_LSDAC_SEN, DB0_TX_LSADC_SEN, DB0_TX_LSDAC_SEN, DB0_RX_SEN, DB0_TX_SEN} = sen0; wire db_dac_mosi_int, db_dac_miso; wire drive_dac_pin; reg drop_dac_pin; reg [5:0] bitcount; reg sclk_d1; // Register copy of outgoing DAC clock to do synchronous edge detect. always @(posedge radio_clk) sclk_d1 <= DB_DAC_SCLK; always @(posedge radio_clk) // If neither DAC is selected keep counter reset if(DB0_DAC_SEN & DB1_DAC_SEN) begin bitcount <= 6'd0; drop_dac_pin <= 1'b0; end else if(~DB_DAC_SCLK & sclk_d1) // Falling edge of SCLK detected. begin bitcount <= bitcount + 6'd1; end else if(bitcount == 0 & DB_DAC_SCLK & ~sclk_d1) // On first rising edge store R/W bit to determine if we tristate after 8bits for a Read. drop_dac_pin <= db_dac_mosi_int; assign drive_dac_pin = (bitcount < 8) | ~drop_dac_pin; // Both DAC's use a single SPI bus on PCB. Select appriate Radio to drive the SPi bus by looking at chip selects. assign { DB_DAC_SCLK, db_dac_mosi_int } = ~DB0_DAC_SEN ? {sclk0, mosi0} : ~DB1_DAC_SEN ? {sclk1,mosi1} : 2'b0; // Data to/from DAC's is bi-dir so tristate driver when reading. assign DB_DAC_MOSI = drive_dac_pin ? db_dac_mosi_int : 1'bz; // I/O Input buffer assign db_dac_miso = DB_DAC_MOSI; // If any SPI Slave is selected (except DAC) then drive SPI clk and MOSI out onto duaghterboard. assign { DB0_SCLK, DB0_MOSI } = (~&sen0[6:0]) ? {sclk0,mosi0} : 2'b0; assign { DB1_SCLK, DB1_MOSI } = (~&sen1[6:0]) ? {sclk1,mosi1} : 2'b0; // Wired OR Mux together the possible sources of read data from SPI devices. assign miso0 = (~DB0_RX_LSADC_SEN & DB0_RX_LSADC_MISO) | (~DB0_RX_SEN & DB0_RX_MISO) | (~DB0_TX_LSADC_SEN & DB0_TX_LSADC_MISO) | (~DB0_TX_SEN & DB0_TX_MISO) | (~DB0_DAC_SEN & db_dac_miso); assign miso1 = (~DB1_RX_LSADC_SEN & DB1_RX_LSADC_MISO) | (~DB1_RX_SEN & DB1_RX_MISO) | (~DB1_TX_LSADC_SEN & DB1_TX_LSADC_MISO) | (~DB1_TX_SEN & DB1_TX_MISO) | (~DB1_DAC_SEN & db_dac_miso); ///////////////////////////////////////////////////////////////////// // // ADC Interface for ADS62P48 // ///////////////////////////////////////////////////////////////////// wire [13:0] rx0_q_inv, rx1_q_inv, rx0_i, rx1_i; // Analog diff pairs on I side of ADC are inverted for layout reasons, but data diff pairs are all swapped as well // so I gets a double negative, and is unchanged. Q must be inverted. capture_ddrlvds #(.WIDTH(14),.X300(1)) cap_db0 (.clk(radio_clk), .reset(radio_rst), .ssclk_p(DB0_ADC_DCLK_P), .ssclk_n(DB0_ADC_DCLK_N), .in_p({{DB0_ADC_DA6_P, DB0_ADC_DA5_P, DB0_ADC_DA4_P, DB0_ADC_DA3_P, DB0_ADC_DA2_P, DB0_ADC_DA1_P, DB0_ADC_DA0_P}, {DB0_ADC_DB6_P, DB0_ADC_DB5_P, DB0_ADC_DB4_P, DB0_ADC_DB3_P, DB0_ADC_DB2_P, DB0_ADC_DB1_P, DB0_ADC_DB0_P}}), .in_n({{DB0_ADC_DA6_N, DB0_ADC_DA5_N, DB0_ADC_DA4_N, DB0_ADC_DA3_N, DB0_ADC_DA2_N, DB0_ADC_DA1_N, DB0_ADC_DA0_N}, {DB0_ADC_DB6_N, DB0_ADC_DB5_N, DB0_ADC_DB4_N, DB0_ADC_DB3_N, DB0_ADC_DB2_N, DB0_ADC_DB1_N, DB0_ADC_DB0_N}}), .out({rx0_i,rx0_q_inv})); assign rx0[31:0] = { rx0_i, 2'b00, ~rx0_q_inv, 2'b00 }; capture_ddrlvds #(.WIDTH(14),.X300(1)) cap_db1 (.clk(radio_clk), .reset(radio_rst), .ssclk_p(DB1_ADC_DCLK_P), .ssclk_n(DB1_ADC_DCLK_N), .in_p({{DB1_ADC_DA6_P, DB1_ADC_DA5_P, DB1_ADC_DA4_P, DB1_ADC_DA3_P, DB1_ADC_DA2_P, DB1_ADC_DA1_P, DB1_ADC_DA0_P}, {DB1_ADC_DB6_P, DB1_ADC_DB5_P, DB1_ADC_DB4_P, DB1_ADC_DB3_P, DB1_ADC_DB2_P, DB1_ADC_DB1_P, DB1_ADC_DB0_P}}), .in_n({{DB1_ADC_DA6_N, DB1_ADC_DA5_N, DB1_ADC_DA4_N, DB1_ADC_DA3_N, DB1_ADC_DA2_N, DB1_ADC_DA1_N, DB1_ADC_DA0_N}, {DB1_ADC_DB6_N, DB1_ADC_DB5_N, DB1_ADC_DB4_N, DB1_ADC_DB3_N, DB1_ADC_DB2_N, DB1_ADC_DB1_N, DB1_ADC_DB0_N}}), .out({rx1_i,rx1_q_inv})); assign rx1[31:0] = { rx1_i, 2'b00, ~rx1_q_inv, 2'b00 }; ///////////////////////////////////////////////////////////////////// // // DAC Interface for AD9146 // ///////////////////////////////////////////////////////////////////// gen_ddrlvds gen_db0 ( .reset(radio_rst), .tx_clk_2x_p(DB0_DAC_DCI_P), .tx_clk_2x_n(DB0_DAC_DCI_N), .tx_frame_p(DB0_DAC_FRAME_P), .tx_frame_n(DB0_DAC_FRAME_N), .tx_d_p({DB0_DAC_D7_P,DB0_DAC_D6_P,DB0_DAC_D5_P,DB0_DAC_D4_P,DB0_DAC_D3_P,DB0_DAC_D2_P,DB0_DAC_D1_P,DB0_DAC_D0_P}), .tx_d_n({DB0_DAC_D7_N,DB0_DAC_D6_N,DB0_DAC_D5_N,DB0_DAC_D4_N,DB0_DAC_D3_N,DB0_DAC_D2_N,DB0_DAC_D1_N,DB0_DAC_D0_N}), .tx_clk_2x(radio_clk_2x), .tx_clk_1x(radio_clk), .i(~tx0[31:16]), .q(~tx0[15:0]), // invert b/c Analog diff pairs are swapped for layout .sync_dacs(sync_dacs_radio0|sync_dacs_radio1) ); gen_ddrlvds gen_db1 ( .reset(radio_rst), .tx_clk_2x_p(DB1_DAC_DCI_P), .tx_clk_2x_n(DB1_DAC_DCI_N), .tx_frame_p(DB1_DAC_FRAME_P), .tx_frame_n(DB1_DAC_FRAME_N), .tx_d_p({DB1_DAC_D7_P,DB1_DAC_D6_P,DB1_DAC_D5_P,DB1_DAC_D4_P,DB1_DAC_D3_P,DB1_DAC_D2_P,DB1_DAC_D1_P,DB1_DAC_D0_P}), .tx_d_n({DB1_DAC_D7_N,DB1_DAC_D6_N,DB1_DAC_D5_N,DB1_DAC_D4_N,DB1_DAC_D3_N,DB1_DAC_D2_N,DB1_DAC_D1_N,DB1_DAC_D0_N}), .tx_clk_2x(radio_clk_2x), .tx_clk_1x(radio_clk), .i(~tx1[31:16]), .q(~tx1[15:0]), // invert b/c Analog diff pairs are swapped for layout .sync_dacs(sync_dacs_radio0|sync_dacs_radio1) ); wire [7:0] leds; assign { LED_ACT1, LED_ACT2, LED_LINK1, LED_LINK2, LED_LINKSTAT, LED_LINKACT } = ~leds; wire [31:0] debug; ////////////////////////////////////////////////////////////////////// // // PCIe Stuff // ////////////////////////////////////////////////////////////////////// localparam IOP2_MSG_WIDTH = 64; localparam DMA_STREAM_WIDTH = `LVFPGA_IFACE_DMA_CHAN_WIDTH; localparam DMA_COUNT_WIDTH = `LVFPGA_IFACE_DMA_SIZE_WIDTH; localparam NUM_TX_STREAMS = `LVFPGA_IFACE_NUM_TX_DMA_CNT; localparam NUM_RX_STREAMS = `LVFPGA_IFACE_NUM_RX_DMA_CNT; localparam TX_STREAM_START_IDX = `LVFPGA_IFACE_TX_DMA_INDEX; localparam RX_STREAM_START_IDX = `LVFPGA_IFACE_RX_DMA_INDEX; wire [DMA_STREAM_WIDTH-1:0] dmatx_tdata, dmarx_tdata; wire dmatx_tvalid, dmarx_tvalid; wire dmatx_tlast, dmarx_tlast; wire dmatx_tready, dmarx_tready; wire [IOP2_MSG_WIDTH-1:0] o_iop2_msg_tdata, i_iop2_msg_tdata; wire o_iop2_msg_tvalid, o_iop2_msg_tlast, o_iop2_msg_tready; wire i_iop2_msg_tvalid, i_iop2_msg_tlast, i_iop2_msg_tready; wire pcie_usr_reg_wr, pcie_usr_reg_rd, pcie_usr_reg_rc, pcie_usr_reg_rdy; wire [1:0] pcie_usr_reg_len; wire [19:0] pcie_usr_reg_addr; wire [31:0] pcie_usr_reg_data_in, pcie_usr_reg_data_out; wire chinch_reg_wr, chinch_reg_rd, chinch_reg_rc, chinch_reg_rdy; wire [1:0] chinch_reg_len; wire [19:0] chinch_reg_addr; wire [31:0] chinch_reg_data_out; wire [63:0] chinch_reg_data_in; wire [(NUM_TX_STREAMS*DMA_STREAM_WIDTH)-1:0] dmatx_tdata_iop2; wire [NUM_TX_STREAMS-1:0] dmatx_tvalid_iop2, dmatx_tready_iop2; wire [(NUM_RX_STREAMS*DMA_STREAM_WIDTH)-1:0] dmarx_tdata_iop2; wire [NUM_RX_STREAMS-1:0] dmarx_tvalid_iop2, dmarx_tready_iop2; //PCIe Express "Physical" DMA and Register logic LvFpga_Chinch_Interface lvfpga_chinch_inst ( .aIoResetIn_n(aIoResetIn_n), .bBusReset(), //Output // Clocks .BusClk(ioport2_clk), .Rio40Clk(rio40_clk), .IDelayRefClk(ioport2_idelay_ref_clk), .aRioClkPllLocked(rio40_clk_locked), .aRioClkPllReset(rio40_clk_reset), // The IO_Port2 asynchronous handshaking pins .aIoReadyOut(aIoReadyOut), .aIoReadyIn(aIoReadyIn), .aIoPort2Restart(aIoPort2Restart), // The IO_Port2 high speed receiver pins .IoRxClock(IoRxClock), .IoRxClock_n(IoRxClock_n), .irIoRxData(irIoRxData), .irIoRxData_n(irIoRxData_n), .irIoRxHeader(irIoRxHeader), .irIoRxHeader_n(irIoRxHeader_n), // The IO_Port2 high speed transmitter interface pins .IoTxClock(IoTxClock), .IoTxClock_n(IoTxClock_n), .itIoTxData(itIoTxData), .itIoTxData_n(itIoTxData_n), .itIoTxHeader(itIoTxHeader), .itIoTxHeader_n(itIoTxHeader_n), // DMA TX Fifos .bDmaTxData(dmatx_tdata_iop2), .bDmaTxValid(dmatx_tvalid_iop2), .bDmaTxReady(dmatx_tready_iop2), .bDmaTxEnabled(), .bDmaTxFifoFullCnt(), // DMA RX Fifos .bDmaRxData(dmarx_tdata_iop2), .bDmaRxValid(dmarx_tvalid_iop2), .bDmaRxReady(dmarx_tready_iop2), .bDmaRxEnabled(), .bDmaRxFifoFreeCnt(), // User Register Port In .bUserRegPortInWt(pcie_usr_reg_wr), .bUserRegPortInRd(pcie_usr_reg_rd), .bUserRegPortInAddr(pcie_usr_reg_addr), .bUserRegPortInData(pcie_usr_reg_data_in), .bUserRegPortInSize(pcie_usr_reg_len), // User Register Port Out .bUserRegPortOutData(pcie_usr_reg_data_out), .bUserRegPortOutDataValid(pcie_usr_reg_rc), .bUserRegPortOutReady(pcie_usr_reg_rdy), // Chinch Register Port Out .bChinchRegPortOutWt(chinch_reg_wr), .bChinchRegPortOutRd(chinch_reg_rd), .bChinchRegPortOutAddr({12'h0, chinch_reg_addr}), .bChinchRegPortOutData({32'h0, chinch_reg_data_out}), .bChinchRegPortOutSize(chinch_reg_len), // User Register Port In .bChinchRegPortInData(chinch_reg_data_in), .bChinchRegPortInDataValid(chinch_reg_rc), .bChinchRegPortInReady(chinch_reg_rdy), // Level interrupt .aIrq(aIrq) ); //PCIe Express adapter logic to link to the AXI crossbar and the WB bus x300_pcie_int #( .DMA_STREAM_WIDTH(DMA_STREAM_WIDTH), .NUM_TX_STREAMS(NUM_TX_STREAMS), .NUM_RX_STREAMS(NUM_RX_STREAMS), .REGPORT_ADDR_WIDTH(20), .REGPORT_DATA_WIDTH(32), .IOP2_MSG_WIDTH(IOP2_MSG_WIDTH) ) x300_pcie_int ( .ioport2_clk(ioport2_clk), .bus_clk(bus_clk), .bus_rst(bus_rst), //DMA TX FIFOs (IoPort2 Clock Domain) .dmatx_tdata_iop2(dmatx_tdata_iop2), .dmatx_tvalid_iop2(dmatx_tvalid_iop2), .dmatx_tready_iop2(dmatx_tready_iop2), //DMA TX FIFOs (IoPort2 Clock Domain) .dmarx_tdata_iop2(dmarx_tdata_iop2), .dmarx_tvalid_iop2(dmarx_tvalid_iop2), .dmarx_tready_iop2(dmarx_tready_iop2), //PCIe User Regport .pcie_usr_reg_wr(pcie_usr_reg_wr), .pcie_usr_reg_rd(pcie_usr_reg_rd), .pcie_usr_reg_addr(pcie_usr_reg_addr), .pcie_usr_reg_data_in(pcie_usr_reg_data_in), .pcie_usr_reg_len(pcie_usr_reg_len), .pcie_usr_reg_data_out(pcie_usr_reg_data_out), .pcie_usr_reg_rc(pcie_usr_reg_rc), .pcie_usr_reg_rdy(pcie_usr_reg_rdy), //Chinch Regport .chinch_reg_wr(chinch_reg_wr), .chinch_reg_rd(chinch_reg_rd), .chinch_reg_addr(chinch_reg_addr), .chinch_reg_data_out(chinch_reg_data_out), .chinch_reg_len(chinch_reg_len), .chinch_reg_data_in(chinch_reg_data_in[31:0]), .chinch_reg_rc(chinch_reg_rc), .chinch_reg_rdy(chinch_reg_rdy), //DMA TX FIFO (Bus Clock Domain) .dmatx_tdata(dmatx_tdata), .dmatx_tlast(dmatx_tlast), .dmatx_tvalid(dmatx_tvalid), .dmatx_tready(dmatx_tready), //DMA RX FIFO (Bus Clock Domain) .dmarx_tdata(dmarx_tdata), .dmarx_tlast(dmarx_tlast), .dmarx_tvalid(dmarx_tvalid), .dmarx_tready(dmarx_tready), //Message FIFO Out (Bus Clock Domain) .rego_tdata(o_iop2_msg_tdata), .rego_tvalid(o_iop2_msg_tvalid), .rego_tlast(o_iop2_msg_tlast), .rego_tready(o_iop2_msg_tready), //Message FIFO In (Bus Clock Domain) .regi_tdata(i_iop2_msg_tdata), .regi_tvalid(i_iop2_msg_tvalid), .regi_tlast(i_iop2_msg_tlast), .regi_tready(i_iop2_msg_tready), //Misc .misc_status({31'h0, aStc3Gpio7}), .debug() ); ////////////////////////////////////////////////////////////////////// // // Configure Ethernet PHY clocking // ////////////////////////////////////////////////////////////////////// `ifdef BUILD_1G wire gige_sfp_clk; IBUFDS_GTE2 gige_clk_sfp_pin (.O(gige_sfp_clk),.I(ETH_CLK_p),.IB(ETH_CLK_n), .CEB(1'b0)); `endif `ifdef BUILD_10G wire xgige_sfp_clk; wire xgige_sfp_clk_bufg; IBUFDS_GTE2 clk_sfp_pin (.O(xgige_sfp_clk),.I(XG_CLK_p),.IB(XG_CLK_n), .CEB(1'b0)); BUFG xgige_bufg_inst ( .I (xgige_sfp_clk), .O (xgige_sfp_clk_bufg) ); `endif ////////////////////////////////////////////////////////////////////// // // Configure Ethernet PHY implemented for PORT0 // ////////////////////////////////////////////////////////////////////// wire mdc0, mdio_in0, mdio_out0, mdio_tri0; wire [4:0] prtad0 = 5'b00100; // MDIO address is 4 `ifdef ETH10G_PORT0 ////////////////////////////////////////////////////////////////////// // // 10GBaseR PHY with XGMII interface to MAC // ////////////////////////////////////////////////////////////////////// wire xgmii_clk0; // 156.25MHz wire [63:0] xgmii_txd0; wire [7:0] xgmii_txc0; wire [63:0] xgmii_rxd0; wire [7:0] xgmii_rxc0; wire [7:0] core_status0; wire xge_phy_resetdone0; ten_gig_eth_pcs_pma_x300_top ten_gig_eth_pcs_pma_x300_top_port0 ( .refclk156(xgige_sfp_clk), .refclk156_buf(xgige_sfp_clk_bufg), .clk156(xgmii_clk0), .reset(global_rst | sw_rst[0]), .xgmii_txd(xgmii_txd0), .xgmii_txc(xgmii_txc0), .xgmii_rxd(xgmii_rxd0), .xgmii_rxc(xgmii_rxc0), .txp(SFP0_TX_p), .txn(SFP0_TX_n), .rxp(SFP0_RX_p), .rxn(SFP0_RX_n), .mdc(mdc0), .mdio_in(mdio_in0), .mdio_out(mdio_out0), .mdio_tri(mdio_tri0), .prtad(prtad0), .core_status(core_status0), // Ignore for now. IJB .resetdone(xge_phy_resetdone0), .signal_detect(~SFPP0_RxLOS), // Undocumented, but it seems Xilinx expect this to be inverted. .tx_fault(SFPP0_TxFault), .tx_disable(SFPP0_TxDisable) ); `else ////////////////////////////////////////////////////////////////////// // // 1000Base-X PHY with GMII interface to MAC // ////////////////////////////////////////////////////////////////////// wire [31:0] gige_phy_misc_dbg0; wire [15:0] gige_phy_int_data0; wire [7:0] gmii_txd0, gmii_rxd0; wire gmii_tx_en0, gmii_tx_er0, gmii_rx_dv0, gmii_rx_er0; wire gmii_clk0; wire [15:0] gmii_status0; assign SFPP0_TxDisable = 1'b0; // Always on. gige_phy_mdio gige_phy_port0 ( .reset(global_rst | sw_rst[0]), .independent_clock(bus_clk), .sfp_clk(gige_sfp_clk), .SFP_TX_p(SFP0_TX_p), .SFP_TX_n(SFP0_TX_n), .SFP_RX_p(SFP0_RX_p), .SFP_RX_n(SFP0_RX_n), .gmii_clk(gmii_clk0), .gmii_txd(gmii_txd0), .gmii_tx_en(gmii_tx_en0), .gmii_tx_er(gmii_tx_er0), .gmii_rxd(gmii_rxd0), .gmii_rx_dv(gmii_rx_dv0), .gmii_rx_er(gmii_rx_er0), .misc_debug(gige_phy_misc_dbg0), .int_data(gige_phy_int_data0), .status_vector(gmii_status0), // MDIO signals .prtad(prtad0), .mdc(mdc0), .mdio_i(mdio_in0), .mdio_o(mdio_out0), .mdio_t(mdio_tri0) ); wire [35:0] CONTROL0; /* -----\/----- EXCLUDED -----\/----- chipscope_ila chipscope_ila_i0 ( .CONTROL(CONTROL0), // INOUT BUS [35:0] .CLK(mdc0), // IN .TRIG0( { gmii_status0, //31:16 3'b0, prtad0, //15:8 4'b0, 1'b0, mdio_in0, mdio_out0, mdio_tri0 //7:0 } ) // IN BUS [191:0] ); chipscope_icon chipscope_icon_i0 ( .CONTROL0(CONTROL0) // INOUT BUS [35:0] ); -----/\----- EXCLUDED -----/\----- */ `endif // !`ifdef ////////////////////////////////////////////////////////////////////// // // Configure Ethernet PHY implemented for PORT1 // ////////////////////////////////////////////////////////////////////// wire mdc1, mdio_in1, mdio_out1, mdio_tri1; wire [4:0] prtad1 = 5'b00100; // MDIO address is 4 `ifdef ETH10G_PORT1 ////////////////////////////////////////////////////////////////////// // // 10GBaseR PHY with XGMII interface to MAC // ////////////////////////////////////////////////////////////////////// wire xgmii_clk1; // 156.25MHz wire [63:0] xgmii_txd1; wire [7:0] xgmii_txc1; wire [63:0] xgmii_rxd1; wire [7:0] xgmii_rxc1; wire [7:0] core_status1; wire xge_phy_resetdone1; ten_gig_eth_pcs_pma_x300_top ten_gig_eth_pcs_pma_x300_top_port1 ( .refclk156(xgige_sfp_clk), .refclk156_buf(xgige_sfp_clk_bufg), .clk156(xgmii_clk1), .reset(global_rst | sw_rst[0]), .xgmii_txd(xgmii_txd1), .xgmii_txc(xgmii_txc1), .xgmii_rxd(xgmii_rxd1), .xgmii_rxc(xgmii_rxc1), .txp(SFP1_TX_p), .txn(SFP1_TX_n), .rxp(SFP1_RX_p), .rxn(SFP1_RX_n), .mdc(mdc1), .mdio_in(mdio_in1), .mdio_out(mdio_out1), .mdio_tri(mdio_tri1), .prtad(prtad0), .core_status(core_status1), // Ignore for now. IJB .resetdone(xge_phy_resetdone1), .signal_detect(~SFPP1_RxLOS), // Undocumented, but it seems Xilinx expect this to be inverted. .tx_fault(SFPP1_TxFault), .tx_disable(SFPP1_TxDisable) ); `else ////////////////////////////////////////////////////////////////////// // // 1000Base-X PHY with GMII interface to MAC // ////////////////////////////////////////////////////////////////////// wire [31:0] gige_phy_misc_dbg1; wire [15:0] gige_phy_int_data1; wire [7:0] gmii_txd1, gmii_rxd1; wire gmii_tx_en1, gmii_tx_er1, gmii_rx_dv1, gmii_rx_er1; wire gmii_clk1; wire [15:0] gmii_status1; assign SFPP1_TxDisable = 1'b0; // Always on. gige_phy_mdio gige_phy_port1 ( .reset(global_rst | sw_rst[0]), .independent_clock(bus_clk), .sfp_clk(gige_sfp_clk), .SFP_TX_p(SFP1_TX_p), .SFP_TX_n(SFP1_TX_n), .SFP_RX_p(SFP1_RX_p), .SFP_RX_n(SFP1_RX_n), .gmii_clk(gmii_clk1), .gmii_txd(gmii_txd1), .gmii_tx_en(gmii_tx_en1), .gmii_tx_er(gmii_tx_er1), .gmii_rxd(gmii_rxd1), .gmii_rx_dv(gmii_rx_dv1), .gmii_rx_er(gmii_rx_er1), .misc_debug(gige_phy_misc_dbg1), .int_data(gige_phy_int_data1), .status_vector(gmii_status1), // MDIO signals .prtad(prtad0), .mdc(mdc1), .mdio_i(mdio_in1), .mdio_o(mdio_out1), .mdio_t(mdio_tri1) ); `endif // !`ifdef /////////////////////////////////////////////////////////////////////////////////// // // Debug bus for logic analyzer use. // /////////////////////////////////////////////////////////////////////////////////// // assign {DB0_TX_IO,DB0_RX_IO} = debug0; // assign {DB1_TX_IO,DB1_RX_IO} = debug1; /* assign debug = { 2'b0, SFPP1_ModAbs, SFPP1_RxLOS, SFPP1_TxFault, SFPP1_RS0, SFPP1_RS1, SFPP1_TxDisable, //8 4'b0, gmii_tx_en, gmii_tx_er, gmii_rx_dv, gmii_rx_er, //8 gmii_txd, gmii_rxd //16 }; */ `ifndef NO_DRAM_FIFOS /////////////////////////////////////////////////////////////////////////////////// // // Xilinx DDR3 Controller and PHY. // /////////////////////////////////////////////////////////////////////////////////// wire ddr3_axi_clk; // 1/4 DDR external clock rate (250MHz) wire ddr3_axi_rst; // Synchronized to ddr_sys_clk wire ddr3_running; // DRAM calibration complete. // Slave Interface Write Address Ports wire [3:0] s_axi_awid; wire [31:0] s_axi_awaddr; wire [7:0] s_axi_awlen; wire [2:0] s_axi_awsize; wire [1:0] s_axi_awburst; wire [0:0] s_axi_awlock; wire [3:0] s_axi_awcache; wire [2:0] s_axi_awprot; wire [3:0] s_axi_awqos; wire s_axi_awvalid; wire s_axi_awready; // Slave Interface Write Data Ports wire [127:0] s_axi_wdata; wire [15:0] s_axi_wstrb; wire s_axi_wlast; wire s_axi_wvalid; wire s_axi_wready; // Slave Interface Write Response Ports wire s_axi_bready; wire [3:0] s_axi_bid; wire [1:0] s_axi_bresp; wire s_axi_bvalid; // Slave Interface Read Address Ports wire [3:0] s_axi_arid; wire [31:0] s_axi_araddr; wire [7:0] s_axi_arlen; wire [2:0] s_axi_arsize; wire [1:0] s_axi_arburst; wire [0:0] s_axi_arlock; wire [3:0] s_axi_arcache; wire [2:0] s_axi_arprot; wire [3:0] s_axi_arqos; wire s_axi_arvalid; wire s_axi_arready; // Slave Interface Read Data Ports wire s_axi_rready; wire [3:0] s_axi_rid; wire [127:0] s_axi_rdata; wire [1:0] s_axi_rresp; wire s_axi_rlast; wire s_axi_rvalid; reg ddr3_axi_rst_reg_n; // Copied this reset circuit from example design. always @(posedge ddr3_axi_clk) ddr3_axi_rst_reg_n <= ~ddr3_axi_rst; /* -----\/----- EXCLUDED -----\/----- //-*************************************************************************** // Traffic Gen related localparams //-*************************************************************************** localparam BL_WIDTH = 10; localparam PORT_MODE = "BI_MODE"; localparam DATA_MODE = 4'b0010; localparam ADDR_MODE = 4'b0011; localparam TST_MEM_INSTR_MODE = "R_W_INSTR_MODE"; localparam EYE_TEST = "FALSE"; // set EYE_TEST = "TRUE" to probe memory // signals. Traffic Generator will only // write to one single location and no // read transactions will be generated. localparam DATA_PATTERN = "DGEN_ALL"; // For small devices, choose one only. // For large device, choose "DGEN_ALL" // "DGEN_HAMMER", "DGEN_WALKING1", // "DGEN_WALKING0","DGEN_ADDR"," // "DGEN_NEIGHBOR","DGEN_PRBS","DGEN_ALL" localparam CMD_PATTERN = "CGEN_ALL"; // "CGEN_PRBS","CGEN_FIXED","CGEN_BRAM", // "CGEN_SEQUENTIAL", "CGEN_ALL" localparam BEGIN_ADDRESS = 32'h00000000; localparam END_ADDRESS = 32'h00ffffff; localparam PRBS_EADDR_MASK_POS = 32'hff000000; localparam CMD_WDT = 'h3FF; localparam WR_WDT = 'h1FFF; localparam RD_WDT = 'h3FF; localparam SEL_VICTIM_LINE = 0; localparam ENFORCE_RD_WR = 0; localparam ENFORCE_RD_WR_CMD = 8'h11; localparam ENFORCE_RD_WR_PATTERN = 3'b000; localparam C_EN_WRAP_TRANS = 0; localparam C_AXI_NBURST_TEST = 0; //-*************************************************************************** // The following localparams refer to width of various ports //-*************************************************************************** localparam BANK_WIDTH = 3; // # of memory Bank Address bits. localparam CK_WIDTH = 1; // # of CK/CK# outputs to memory. localparam COL_WIDTH = 10; // # of memory Column Address bits. localparam CS_WIDTH = 1; // # of unique CS outputs to memory. localparam nCS_PER_RANK = 1; // # of unique CS outputs per rank for phy localparam CKE_WIDTH = 1; // # of CKE outputs to memory. localparam DATA_BUF_ADDR_WIDTH = 5; localparam DQ_CNT_WIDTH = 5; // = ceil(log2(DQ_WIDTH)) localparam DQ_PER_DM = 8; localparam DM_WIDTH = 4; // # of DM (data mask) localparam DQ_WIDTH = 32; // # of DQ (data) localparam DQS_WIDTH = 4; localparam DQS_CNT_WIDTH = 2; // = ceil(log2(DQS_WIDTH)) localparam DRAM_WIDTH = 8; // # of DQ per DQS localparam ECC = "OFF"; localparam nBANK_MACHS = 4; localparam RANKS = 1; // # of Ranks. localparam ODT_WIDTH = 1; // # of ODT outputs to memory. localparam ROW_WIDTH = 15; // # of memory Row Address bits. localparam ADDR_WIDTH = 29; // # = RANK_WIDTH + BANK_WIDTH // + ROW_WIDTH + COL_WIDTH; // Chip Select is always tied to low for // single rank devices localparam USE_CS_PORT = 1; // # = 1, When Chip Select (CS#) output is enabled // = 0, When Chip Select (CS#) output is disabled // If CS_N disabled, user must connect // DRAM CS_N input(s) to ground localparam USE_DM_PORT = 1; // # = 1, When Data Mask option is enabled // = 0, When Data Mask option is disbaled // When Data Mask option is disabled in // MIG Controller Options page, the logic // related to Data Mask should not get // synthesized localparam USE_ODT_PORT = 1; // # = 1, When ODT output is enabled // = 0, When ODT output is disabled localparam PHY_CONTROL_MASTER_BANK = 1; // The bank index where master PHY_CONTROL resides; // equal to the PLL residing bank localparam MEM_DENSITY = "4Gb"; // Indicates the density of the Memory part // Added for the sake of Vivado simulations localparam MEM_SPEEDGRADE = "125"; // Indicates the Speed grade of Memory Part // Added for the sake of Vivado simulations localparam MEM_DEVICE_WIDTH = 16; // Indicates the device width of the Memory Part // Added for the sake of Vivado simulations //-*************************************************************************** // The following localparams are mode register settings //-*************************************************************************** localparam AL = "0"; // DDR3 SDRAM: // Additive Latency (Mode Register 1). // # = "0", "CL-1", "CL-2". // DDR2 SDRAM: // Additive Latency (Extended Mode Register). localparam nAL = 0; // # Additive Latency in number of clock // cycles. localparam BURST_MODE = "8"; // DDR3 SDRAM: // Burst Length (Mode Register 0). // # = "8", "4", "OTF". // DDR2 SDRAM: // Burst Length (Mode Register). // # = "8", "4". localparam BURST_TYPE = "SEQ"; // DDR3 SDRAM: Burst Type (Mode Register 0). // DDR2 SDRAM: Burst Type (Mode Register). // # = "SEQ" - (Sequential), // = "INT" - (Interleaved). localparam CL = 7; // in number of clock cycles // DDR3 SDRAM: CAS Latency (Mode Register 0). // DDR2 SDRAM: CAS Latency (Mode Register). localparam CWL = 6; // in number of clock cycles // DDR3 SDRAM: CAS Write Latency (Mode Register 2). // DDR2 SDRAM: Can be ignored localparam OUTPUT_DRV = "HIGH"; // Output Driver Impedance Control (Mode Register 1). // # = "HIGH" - RZQ/7, // = "LOW" - RZQ/6. localparam RTT_NOM = "60"; // RTT_NOM (ODT) (Mode Register 1). // = "120" - RZQ/2, // = "60" - RZQ/4, // = "40" - RZQ/6. localparam RTT_WR = "OFF"; // RTT_WR (ODT) (Mode Register 2). // # = "OFF" - Dynamic ODT off, // = "120" - RZQ/2, // = "60" - RZQ/4, localparam ADDR_CMD_MODE = "1T" ; // # = "1T", "2T". localparam REG_CTRL = "OFF"; // # = "ON" - RDIMMs, // = "OFF" - Components, SODIMMs, UDIMMs. localparam CA_MIRROR = "OFF"; // C/A mirror opt for DDR3 dual rank //-*************************************************************************** // The following localparams are multiplier and divisor factors for PLLE2. // Based on the selected design frequency these localparams vary. //-*************************************************************************** localparam CLKIN_PERIOD = 10000; // Input Clock Period localparam CLKFBOUT_MULT = 10; // write PLL VCO multiplier localparam DIVCLK_DIVIDE = 1; // write PLL VCO divisor localparam CLKOUT0_PHASE = 337.5; // Phase for PLL output clock (CLKOUT0) localparam CLKOUT0_DIVIDE = 2; // VCO output divisor for PLL output clock (CLKOUT0) localparam CLKOUT1_DIVIDE = 2; // VCO output divisor for PLL output clock (CLKOUT1) localparam CLKOUT2_DIVIDE = 32; // VCO output divisor for PLL output clock (CLKOUT2) localparam CLKOUT3_DIVIDE = 8; // VCO output divisor for PLL output clock (CLKOUT3) //-*************************************************************************** // Memory Timing Localparams. These localparams varies based on the selected // memory part. //-*************************************************************************** localparam tCKE = 5000; // memory tCKE paramter in pS localparam tFAW = 30000; // memory tRAW paramter in pS. localparam tRAS = 35000; // memory tRAS paramter in pS. localparam tRCD = 13750; // memory tRCD paramter in pS. localparam tREFI = 7800000; // memory tREFI paramter in pS. localparam tRFC = 300000; // memory tRFC paramter in pS. localparam tRP = 13750; // memory tRP paramter in pS. localparam tRRD = 6000; // memory tRRD paramter in pS. localparam tRTP = 7500; // memory tRTP paramter in pS. localparam tWTR = 7500; // memory tWTR paramter in pS. localparam tZQI = 128_000_000; // memory tZQI paramter in nS. localparam tZQCS = 64; // memory tZQCS paramter in clock cycles. //-*************************************************************************** // Simulation localparams //-*************************************************************************** localparam SIM_BYPASS_INIT_CAL = "OFF"; // # = "OFF" - Complete memory init & // calibration sequence // # = "SKIP" - Not supported // # = "FAST" - Complete memory init & use // abbreviated calib sequence localparam SIMULATION = "FALSE"; // Should be TRUE during design simulations and // FALSE during implementations //-*************************************************************************** // The following localparams varies based on the pin out entered in MIG GUI. // Do not change any of these localparams directly by editing the RTL. // Any changes required should be done through GUI and the design regenerated. //-*************************************************************************** localparam BYTE_LANES_B0 = 4'b1111; // Byte lanes used in an IO column. localparam BYTE_LANES_B1 = 4'b1110; // Byte lanes used in an IO column. localparam BYTE_LANES_B2 = 4'b0000; // Byte lanes used in an IO column. localparam BYTE_LANES_B3 = 4'b0000; // Byte lanes used in an IO column. localparam BYTE_LANES_B4 = 4'b0000; // Byte lanes used in an IO column. localparam DATA_CTL_B0 = 4'b1111; // Indicates Byte lane is data byte lane // or control Byte lane. '1' in a bit // position indicates a data byte lane and // a '0' indicates a control byte lane localparam DATA_CTL_B1 = 4'b0000; // Indicates Byte lane is data byte lane // or control Byte lane. '1' in a bit // position indicates a data byte lane and // a '0' indicates a control byte lane localparam DATA_CTL_B2 = 4'b0000; // Indicates Byte lane is data byte lane // or control Byte lane. '1' in a bit // position indicates a data byte lane and // a '0' indicates a control byte lane localparam DATA_CTL_B3 = 4'b0000; // Indicates Byte lane is data byte lane // or control Byte lane. '1' in a bit // position indicates a data byte lane and // a '0' indicates a control byte lane localparam DATA_CTL_B4 = 4'b0000; // Indicates Byte lane is data byte lane // or control Byte lane. '1' in a bit // position indicates a data byte lane and // a '0' indicates a control byte lane localparam PHY_0_BITLANES = 48'h3FE_3FE_3FE_2FF; localparam PHY_1_BITLANES = 48'h3FF_FFF_C00_000; localparam PHY_2_BITLANES = 48'h000_000_000_000; // control/address/data pin mapping localparams localparam CK_BYTE_MAP = 144'h00_00_00_00_00_00_00_00_00_00_00_00_00_00_00_00_00_13; localparam ADDR_MAP = 192'h000_139_138_137_136_135_134_133_132_131_130_129_128_127_126_12B; localparam BANK_MAP = 36'h12A_125_124; localparam CAS_MAP = 12'h122; localparam CKE_ODT_BYTE_MAP = 8'h00; localparam CKE_MAP = 96'h000_000_000_000_000_000_000_11B; localparam ODT_MAP = 96'h000_000_000_000_000_000_000_11A; localparam CS_MAP = 120'h000_000_000_000_000_000_000_000_000_120; localparam PARITY_MAP = 12'h000; localparam RAS_MAP = 12'h123; localparam WE_MAP = 12'h121; localparam DQS_BYTE_MAP = 144'h00_00_00_00_00_00_00_00_00_00_00_00_00_00_00_01_02_03; localparam DATA0_MAP = 96'h031_032_033_034_035_036_037_038; localparam DATA1_MAP = 96'h021_022_023_024_025_026_027_028; localparam DATA2_MAP = 96'h011_012_013_014_015_016_017_018; localparam DATA3_MAP = 96'h000_001_002_003_004_005_006_007; localparam DATA4_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA5_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA6_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA7_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA8_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA9_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA10_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA11_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA12_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA13_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA14_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA15_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA16_MAP = 96'h000_000_000_000_000_000_000_000; localparam DATA17_MAP = 96'h000_000_000_000_000_000_000_000; localparam MASK0_MAP = 108'h000_000_000_000_000_009_019_029_039; localparam MASK1_MAP = 108'h000_000_000_000_000_000_000_000_000; localparam SLOT_0_CONFIG = 8'b0000_0001; // Mapping of Ranks. localparam SLOT_1_CONFIG = 8'b0000_0000; // Mapping of Ranks. localparam MEM_ADDR_ORDER = "BANK_ROW_COLUMN"; //-*************************************************************************** // IODELAY and PHY related localparams //-*************************************************************************** localparam IODELAY_HP_MODE = "ON"; // to phy_top localparam IBUF_LPWR_MODE = "OFF"; // to phy_top localparam DATA_IO_IDLE_PWRDWN = "ON"; // # = "ON", "OFF" localparam BANK_TYPE = "HP_IO"; // # = "HP_IO", "HPL_IO", "HR_IO", "HRL_IO" localparam DATA_IO_PRIM_TYPE = "HP_LP"; // # = "HP_LP", "HR_LP", "DEFAULT" localparam CKE_ODT_AUX = "FALSE"; localparam USER_REFRESH = "OFF"; localparam WRLVL = "ON"; // # = "ON" - DDR3 SDRAM // = "OFF" - DDR2 SDRAM. localparam ORDERING = "NORM"; // # = "NORM", "STRICT", "RELAXED". localparam CALIB_ROW_ADD = 16'h0000; // Calibration row address will be used for // calibration read and write operations localparam CALIB_COL_ADD = 12'h000; // Calibration column address will be used for // calibration read and write operations localparam CALIB_BA_ADD = 3'h0; // Calibration bank address will be used for // calibration read and write operations localparam TCQ = 100; localparam IODELAY_GRP = "IODELAY_MIG"; // It is associated to a set of IODELAYs with // an IDELAYCTRL that have same IODELAY CONTROLLER // clock frequency. localparam SYSCLK_TYPE = "SINGLE_ENDED"; // System clock type DIFFERENTIAL, SINGLE_ENDED, // NO_BUFFER localparam REFCLK_TYPE = "NO_BUFFER"; // Reference clock type DIFFERENTIAL, SINGLE_ENDED, // NO_BUFFER, USE_SYSTEM_CLOCK localparam DRAM_TYPE = "DDR3"; localparam CAL_WIDTH = "HALF"; localparam STARVE_LIMIT = 2; // # = 2,3,4. //-*************************************************************************** // Referece clock frequency localparams //-*************************************************************************** localparam REFCLK_FREQ = 200.0; // IODELAYCTRL reference clock frequency localparam DIFF_TERM_REFCLK = "TRUE"; // Differential Termination for idelay // reference clock input pins //-*************************************************************************** // System clock frequency localparams //-*************************************************************************** localparam tCK = 2000; // memory tCK paramter. // # = Clock Period in pS. localparam nCK_PER_CLK = 4; // # of memory CKs per fabric CLK localparam DIFF_TERM_SYSCLK = "TRUE"; // Differential Termination for System // clock input pins //-*************************************************************************** // AXI4 Shim localparams //-*************************************************************************** localparam C_S_AXI_ID_WIDTH = 4; // Width of all master and slave ID signals. // # = >= 1. localparam C_S_AXI_MEM_SIZE = "2147483648"; // Address Space required for this component localparam C_S_AXI_ADDR_WIDTH = 32; // Width of S_AXI_AWADDR; S_AXI_ARADDR, M_AXI_AWADDR and // M_AXI_ARADDR for all SI/MI slots. // # = 32. localparam C_S_AXI_DATA_WIDTH = 128; // Width of WDATA and RDATA on SI slot. // Must be <= APP_DATA_WIDTH. // # = 32, 64, 128, 256. localparam C_MC_nCK_PER_CLK = 4; // Indicates whether to instatiate upsizer // Range: 0, 1 localparam C_S_AXI_SUPPORTS_NARROW_BURST = 1; // Indicates whether to instatiate upsizer // Range: 0, 1 localparam C_RD_WR_ARB_ALGORITHM = "ROUND_ROBIN"; // Indicates the Arbitration // Allowed values - "TDM", "ROUND_ROBIN", // "RD_PRI_REG", "RD_PRI_REG_STARVE_LIMIT" // "WRITE_PRIORITY", "WRITE_PRIORITY_REG" localparam C_S_AXI_REG_EN0 = 20'h00000; // C_S_AXI_REG_EN0[00] = Reserved // C_S_AXI_REG_EN0[04] = AW CHANNEL REGISTER SLICE // C_S_AXI_REG_EN0[05] = W CHANNEL REGISTER SLICE // C_S_AXI_REG_EN0[06] = B CHANNEL REGISTER SLICE // C_S_AXI_REG_EN0[07] = R CHANNEL REGISTER SLICE // C_S_AXI_REG_EN0[08] = AW CHANNEL UPSIZER REGISTER SLICE // C_S_AXI_REG_EN0[09] = W CHANNEL UPSIZER REGISTER SLICE // C_S_AXI_REG_EN0[10] = AR CHANNEL UPSIZER REGISTER SLICE // C_S_AXI_REG_EN0[11] = R CHANNEL UPSIZER REGISTER SLICE localparam C_S_AXI_REG_EN1 = 20'h00000; // Instatiates register slices after the upsizer. // The type of register is specified for each channel // in a vector. 4 bits per channel are used. // C_S_AXI_REG_EN1[03:00] = AW CHANNEL REGISTER SLICE // C_S_AXI_REG_EN1[07:04] = W CHANNEL REGISTER SLICE // C_S_AXI_REG_EN1[11:08] = B CHANNEL REGISTER SLICE // C_S_AXI_REG_EN1[15:12] = AR CHANNEL REGISTER SLICE // C_S_AXI_REG_EN1[20:16] = R CHANNEL REGISTER SLICE // Possible values for each channel are: // // 0 => BYPASS = The channel is just wired through the // module. // 1 => FWD = The master VALID and payload signals // are registrated. // 2 => REV = The slave ready signal is registrated // 3 => FWD_REV = Both FWD and REV // 4 => SLAVE_FWD = All slave side signals and master // VALID and payload are registrated. // 5 => SLAVE_RDY = All slave side signals and master // READY are registrated. // 6 => INPUTS = Slave and Master side inputs are // registrated. // 7 => ADDRESS = Optimized for address channel localparam C_S_AXI_CTRL_ADDR_WIDTH = 32; // Width of AXI-4-Lite address bus localparam C_S_AXI_CTRL_DATA_WIDTH = 32; // Width of AXI-4-Lite data buses localparam C_S_AXI_BASEADDR = 32'h0000_0000; // Base address of AXI4 Memory Mapped bus. localparam C_ECC_ONOFF_RESET_VALUE = 1; // Controls ECC on/off value at startup/reset localparam C_ECC_CE_COUNTER_WIDTH = 8; // The external memory to controller clock ratio. //-*************************************************************************** // Debug localparams //-*************************************************************************** localparam DEBUG_PORT = "OFF"; // # = "ON" Enable debug signals/controls. // = "OFF" Disable debug signals/controls. //-*************************************************************************** // Temparature monitor localparam //-*************************************************************************** localparam TEMP_MON_CONTROL = "INTERNAL"; // # = "INTERNAL", "EXTERNAL" localparam RST_ACT_LOW = 1; // =1 for active low reset, // =0 for active high. //-******************* localparam CMD_PIPE_PLUS1 = "ON"; // add pipeline stage between MC and PHY localparam DATA_WIDTH = 32; localparam ECC_WIDTH = (ECC == "OFF")? 0 : (DATA_WIDTH <= 4)? 4 : (DATA_WIDTH <= 10)? 5 : (DATA_WIDTH <= 26)? 6 : (DATA_WIDTH <= 57)? 7 : (DATA_WIDTH <= 120)? 8 : (DATA_WIDTH <= 247)? 9 : 10; localparam ECC_TEST = "OFF"; localparam RANK_WIDTH = clogb2(RANKS); localparam DATA_BUF_OFFSET_WIDTH = 1; localparam MC_ERR_ADDR_WIDTH = ((CS_WIDTH == 1) ? 0 : RANK_WIDTH) + BANK_WIDTH + ROW_WIDTH + COL_WIDTH + DATA_BUF_OFFSET_WIDTH; localparam tPRDI = 1_000_000; // memory tPRDI paramter in pS. localparam PAYLOAD_WIDTH = (ECC_TEST == "OFF") ? DATA_WIDTH : DQ_WIDTH; //localparam BURST_LENGTH = STR_TO_INT(BURST_MODE); localparam APP_DATA_WIDTH = 2 * nCK_PER_CLK * PAYLOAD_WIDTH; localparam APP_MASK_WIDTH = APP_DATA_WIDTH / 8; -----/\----- EXCLUDED -----/\----- */ ddr3_32bit /* -----\/----- EXCLUDED -----\/----- #( .TCQ (TCQ), .ADDR_CMD_MODE (ADDR_CMD_MODE), .AL (AL), .PAYLOAD_WIDTH (PAYLOAD_WIDTH), .BANK_WIDTH (BANK_WIDTH), .BURST_MODE (BURST_MODE), .BURST_TYPE (BURST_TYPE), .CA_MIRROR (CA_MIRROR), .CK_WIDTH (CK_WIDTH), .COL_WIDTH (COL_WIDTH), .CMD_PIPE_PLUS1 (CMD_PIPE_PLUS1), .CS_WIDTH (CS_WIDTH), .nCS_PER_RANK (nCS_PER_RANK), .CKE_WIDTH (CKE_WIDTH), .DATA_WIDTH (DATA_WIDTH), .DATA_BUF_ADDR_WIDTH (DATA_BUF_ADDR_WIDTH), .DQ_CNT_WIDTH (DQ_CNT_WIDTH), .DQ_PER_DM (DQ_PER_DM), .DQ_WIDTH (DQ_WIDTH), .DQS_CNT_WIDTH (DQS_CNT_WIDTH), .DQS_WIDTH (DQS_WIDTH), .DRAM_WIDTH (DRAM_WIDTH), .ECC (ECC), .ECC_WIDTH (ECC_WIDTH), .ECC_TEST (ECC_TEST), .MC_ERR_ADDR_WIDTH (MC_ERR_ADDR_WIDTH), .nAL (nAL), .nBANK_MACHS (nBANK_MACHS), .CKE_ODT_AUX (CKE_ODT_AUX), .ORDERING (ORDERING), .OUTPUT_DRV (OUTPUT_DRV), .IBUF_LPWR_MODE (IBUF_LPWR_MODE), .IODELAY_HP_MODE (IODELAY_HP_MODE), .DATA_IO_IDLE_PWRDWN (DATA_IO_IDLE_PWRDWN), .BANK_TYPE (BANK_TYPE), .DATA_IO_PRIM_TYPE (DATA_IO_PRIM_TYPE), .REG_CTRL (REG_CTRL), .RTT_NOM (RTT_NOM), .RTT_WR (RTT_WR), .CL (CL), .CWL (CWL), .tCKE (tCKE), .tFAW (tFAW), .tPRDI (tPRDI), .tRAS (tRAS), .tRCD (tRCD), .tREFI (tREFI), .tRFC (tRFC), .tRP (tRP), .tRRD (tRRD), .tRTP (tRTP), .tWTR (tWTR), .tZQI (tZQI), .tZQCS (tZQCS), .USER_REFRESH (USER_REFRESH), .WRLVL (WRLVL), .DEBUG_PORT (DEBUG_PORT), .RANKS (RANKS), .ODT_WIDTH (ODT_WIDTH), .ROW_WIDTH (ROW_WIDTH), .ADDR_WIDTH (ADDR_WIDTH), .SIM_BYPASS_INIT_CAL (SIM_BYPASS_INIT_CAL), .SIMULATION (SIMULATION), .BYTE_LANES_B0 (BYTE_LANES_B0), .BYTE_LANES_B1 (BYTE_LANES_B1), .BYTE_LANES_B2 (BYTE_LANES_B2), .BYTE_LANES_B3 (BYTE_LANES_B3), .BYTE_LANES_B4 (BYTE_LANES_B4), .DATA_CTL_B0 (DATA_CTL_B0), .DATA_CTL_B1 (DATA_CTL_B1), .DATA_CTL_B2 (DATA_CTL_B2), .DATA_CTL_B3 (DATA_CTL_B3), .DATA_CTL_B4 (DATA_CTL_B4), .PHY_0_BITLANES (PHY_0_BITLANES), .PHY_1_BITLANES (PHY_1_BITLANES), .PHY_2_BITLANES (PHY_2_BITLANES), .CK_BYTE_MAP (CK_BYTE_MAP), .ADDR_MAP (ADDR_MAP), .BANK_MAP (BANK_MAP), .CAS_MAP (CAS_MAP), .CKE_ODT_BYTE_MAP (CKE_ODT_BYTE_MAP), .CKE_MAP (CKE_MAP), .ODT_MAP (ODT_MAP), .CS_MAP (CS_MAP), .PARITY_MAP (PARITY_MAP), .RAS_MAP (RAS_MAP), .WE_MAP (WE_MAP), .DQS_BYTE_MAP (DQS_BYTE_MAP), .DATA0_MAP (DATA0_MAP), .DATA1_MAP (DATA1_MAP), .DATA2_MAP (DATA2_MAP), .DATA3_MAP (DATA3_MAP), .DATA4_MAP (DATA4_MAP), .DATA5_MAP (DATA5_MAP), .DATA6_MAP (DATA6_MAP), .DATA7_MAP (DATA7_MAP), .DATA8_MAP (DATA8_MAP), .DATA9_MAP (DATA9_MAP), .DATA10_MAP (DATA10_MAP), .DATA11_MAP (DATA11_MAP), .DATA12_MAP (DATA12_MAP), .DATA13_MAP (DATA13_MAP), .DATA14_MAP (DATA14_MAP), .DATA15_MAP (DATA15_MAP), .DATA16_MAP (DATA16_MAP), .DATA17_MAP (DATA17_MAP), .MASK0_MAP (MASK0_MAP), .MASK1_MAP (MASK1_MAP), .CALIB_ROW_ADD (CALIB_ROW_ADD), .CALIB_COL_ADD (CALIB_COL_ADD), .CALIB_BA_ADD (CALIB_BA_ADD), .SLOT_0_CONFIG (SLOT_0_CONFIG), .SLOT_1_CONFIG (SLOT_1_CONFIG), .MEM_ADDR_ORDER (MEM_ADDR_ORDER), .USE_CS_PORT (USE_CS_PORT), .USE_DM_PORT (USE_DM_PORT), .USE_ODT_PORT (USE_ODT_PORT), .PHY_CONTROL_MASTER_BANK (PHY_CONTROL_MASTER_BANK), .TEMP_MON_CONTROL (TEMP_MON_CONTROL), .DM_WIDTH (DM_WIDTH), .nCK_PER_CLK (nCK_PER_CLK), .tCK (tCK), .DIFF_TERM_SYSCLK (DIFF_TERM_SYSCLK), .CLKIN_PERIOD (CLKIN_PERIOD), .CLKFBOUT_MULT (CLKFBOUT_MULT), .DIVCLK_DIVIDE (DIVCLK_DIVIDE), .CLKOUT0_PHASE (CLKOUT0_PHASE), .CLKOUT0_DIVIDE (CLKOUT0_DIVIDE), .CLKOUT1_DIVIDE (CLKOUT1_DIVIDE), .CLKOUT2_DIVIDE (CLKOUT2_DIVIDE), .CLKOUT3_DIVIDE (CLKOUT3_DIVIDE), .C_S_AXI_ID_WIDTH (C_S_AXI_ID_WIDTH), .C_S_AXI_ADDR_WIDTH (C_S_AXI_ADDR_WIDTH), .C_S_AXI_DATA_WIDTH (C_S_AXI_DATA_WIDTH), .C_MC_nCK_PER_CLK (C_MC_nCK_PER_CLK), .C_S_AXI_SUPPORTS_NARROW_BURST (C_S_AXI_SUPPORTS_NARROW_BURST), .C_RD_WR_ARB_ALGORITHM (C_RD_WR_ARB_ALGORITHM), .C_S_AXI_REG_EN0 (C_S_AXI_REG_EN0), .C_S_AXI_REG_EN1 (C_S_AXI_REG_EN1), .C_S_AXI_CTRL_ADDR_WIDTH (C_S_AXI_CTRL_ADDR_WIDTH), .C_S_AXI_CTRL_DATA_WIDTH (C_S_AXI_CTRL_DATA_WIDTH), .C_S_AXI_BASEADDR (C_S_AXI_BASEADDR), .C_ECC_ONOFF_RESET_VALUE (C_ECC_ONOFF_RESET_VALUE), .C_ECC_CE_COUNTER_WIDTH (C_ECC_CE_COUNTER_WIDTH), .SYSCLK_TYPE (SYSCLK_TYPE), .REFCLK_TYPE (REFCLK_TYPE), .REFCLK_FREQ (REFCLK_FREQ), .DIFF_TERM_REFCLK (DIFF_TERM_REFCLK), .IODELAY_GRP (IODELAY_GRP), .CAL_WIDTH (CAL_WIDTH), .STARVE_LIMIT (STARVE_LIMIT), .DRAM_TYPE (DRAM_TYPE), .RST_ACT_LOW (RST_ACT_LOW) ) -----/\----- EXCLUDED -----/\----- */ u_ddr3_32bit ( // Memory interface ports .ddr3_addr (ddr3_addr), .ddr3_ba (ddr3_ba), .ddr3_cas_n (ddr3_cas_n), .ddr3_ck_n (ddr3_ck_n), .ddr3_ck_p (ddr3_ck_p), .ddr3_cke (ddr3_cke), .ddr3_ras_n (ddr3_ras_n), .ddr3_reset_n (ddr3_reset_n), .ddr3_we_n (ddr3_we_n), .ddr3_dq (ddr3_dq), .ddr3_dqs_n (ddr3_dqs_n), .ddr3_dqs_p (ddr3_dqs_p), .init_calib_complete (ddr3_running), .ddr3_cs_n (ddr3_cs_n), .ddr3_dm (ddr3_dm), .ddr3_odt (ddr3_odt), // Application interface ports .ui_clk (ddr3_axi_clk), // 250MHz clock out .ui_clk_sync_rst (ddr3_axi_rst), // Active high Reset signal synchronised to 250MHz .aresetn (ddr3_axi_rst_reg_n), .app_sr_req (1'b0), .app_sr_active (app_sr_active), .app_ref_req (1'b0), .app_ref_ack (app_ref_ack), .app_zq_req (1'b0), .app_zq_ack (app_zq_ack), // Slave Interface Write Address Ports .s_axi_awid (s_axi_awid), .s_axi_awaddr (s_axi_awaddr), .s_axi_awlen (s_axi_awlen), .s_axi_awsize (s_axi_awsize), .s_axi_awburst (s_axi_awburst), .s_axi_awlock (s_axi_awlock), .s_axi_awcache (s_axi_awcache), .s_axi_awprot (s_axi_awprot), .s_axi_awqos (s_axi_awqos), .s_axi_awvalid (s_axi_awvalid), .s_axi_awready (s_axi_awready), // Slave Interface Write Data Ports .s_axi_wdata (s_axi_wdata), .s_axi_wstrb (s_axi_wstrb), .s_axi_wlast (s_axi_wlast), .s_axi_wvalid (s_axi_wvalid), .s_axi_wready (s_axi_wready), // Slave Interface Write Response Ports .s_axi_bid (s_axi_bid), .s_axi_bresp (s_axi_bresp), .s_axi_bvalid (s_axi_bvalid), .s_axi_bready (s_axi_bready), // Slave Interface Read Address Ports .s_axi_arid (s_axi_arid), .s_axi_araddr (s_axi_araddr), .s_axi_arlen (s_axi_arlen), .s_axi_arsize (s_axi_arsize), .s_axi_arburst (s_axi_arburst), .s_axi_arlock (s_axi_arlock), .s_axi_arcache (s_axi_arcache), .s_axi_arprot (s_axi_arprot), .s_axi_arqos (s_axi_arqos), .s_axi_arvalid (s_axi_arvalid), .s_axi_arready (s_axi_arready), // Slave Interface Read Data Ports .s_axi_rid (s_axi_rid), .s_axi_rdata (s_axi_rdata), .s_axi_rresp (s_axi_rresp), .s_axi_rlast (s_axi_rlast), .s_axi_rvalid (s_axi_rvalid), .s_axi_rready (s_axi_rready), // System Clock Ports .sys_clk_i (sys_clk_i), // From external 100MHz source. .sys_rst (~global_rst) // IJB. Poorly named active low. Should change RST_ACT_LOW. ); `endif // `ifndef NO_DRAM_FIFOS /////////////////////////////////////////////////////////////////////////////////// // // X300 Core // /////////////////////////////////////////////////////////////////////////////////// x300_core x300_core ( .radio_clk(radio_clk), .radio_rst(radio_rst), .bus_clk(bus_clk), .bus_rst(bus_rst), .sw_rst(sw_rst), `ifdef DEBUG_UART .fp_gpio(FrontPanelGpio[9:0]), // Discard upper unsued bits. `else .fp_gpio(FrontPanelGpio[11:0]), // Discard upper unsued bits. `endif // Radio0 signals .rx0(rx0), .tx0(tx0), .db_gpio0({DB0_TX_IO,DB0_RX_IO}), .sen0(sen0), .sclk0(sclk0), .mosi0(mosi0), .miso0(miso0), .radio_led0(led0), .radio_misc0({DB_ADC_RESET, DB_DAC_RESET,DB0_DAC_ENABLE}), .sync_dacs_radio0(sync_dacs_radio0), // Radio1 signals .rx1(rx1), .tx1(tx1), .db_gpio1({DB1_TX_IO,DB1_RX_IO}), .sen1(sen1), .sclk1(sclk1), .mosi1(mosi1), .miso1(miso1), .radio_led1(led1), .radio_misc1({DB1_DAC_ENABLE}), .sync_dacs_radio1(sync_dacs_radio1), // I2C bus .db_scl(DB_SCL), .db_sda(DB_SDA), // External clock gen .ext_ref_clk(ref_clk_10mhz), .clock_ref_sel(ClockRefSelect), .clock_misc_opt({GPSDO_PWR_ENA, TCXO_ENA}), .LMK_Status(LMK_Status[1:0]), .LMK_Holdover(LMK_Holdover), .LMK_Lock(LMK_Lock), .LMK_Sync(LMK_Sync), .LMK_SEN(LMK_SEN), .LMK_SCLK(LMK_SCLK), .LMK_MOSI(LMK_MOSI), // SFP+ 0 flags .SFPP0_SCL(SFPP0_SCL), .SFPP0_SDA(SFPP0_SDA), .SFPP0_ModAbs(SFPP0_ModAbs), .SFPP0_TxFault(SFPP0_TxFault), .SFPP0_RxLOS(SFPP0_RxLOS), .SFPP0_RS1(SFPP0_RS1), .SFPP0_RS0(SFPP0_RS0), // SFP+ 1 flags .SFPP1_SCL(SFPP1_SCL), .SFPP1_SDA(SFPP1_SDA), .SFPP1_ModAbs(SFPP1_ModAbs), .SFPP1_TxFault(SFPP1_TxFault), .SFPP1_RxLOS(SFPP1_RxLOS), .SFPP1_RS1(SFPP1_RS1), .SFPP1_RS0(SFPP1_RS0), // MDIO bus to SFP0 .mdc0(mdc0), .mdio_in0(mdio_in0), .mdio_out0(mdio_out0), // SFP+ 0 packet interface `ifdef ETH10G_PORT0 .xgmii_clk0(xgmii_clk0), .xgmii_txd0(xgmii_txd0), .xgmii_txc0(xgmii_txc0), .xgmii_rxd0(xgmii_rxd0), .xgmii_rxc0(xgmii_rxc0), .xge_phy_resetdone0(xge_phy_resetdone0), `else .gmii_clk0(gmii_clk0), .gmii_txd0(gmii_txd0), .gmii_tx_en0(gmii_tx_en0), .gmii_tx_er0(gmii_tx_er0), .gmii_rxd0(gmii_rxd0), .gmii_rx_dv0(gmii_rx_dv0), .gmii_rx_er0(gmii_rx_er0), `endif // !`ifdef // MDIO bus to SFP1 .mdc1(mdc1), .mdio_in1(mdio_in1), .mdio_out1(mdio_out1), // SFP+ 1 packet interface `ifdef ETH10G_PORT1 .xgmii_clk1(xgmii_clk1), .xgmii_txd1(xgmii_txd1), .xgmii_txc1(xgmii_txc1), .xgmii_rxd1(xgmii_rxd1), .xgmii_rxc1(xgmii_rxc1), .xge_phy_resetdone1(xge_phy_resetdone1), `else .gmii_clk1(gmii_clk1), .gmii_txd1(gmii_txd1), .gmii_tx_en1(gmii_tx_en1), .gmii_tx_er1(gmii_tx_er1), .gmii_rxd1(gmii_rxd1), .gmii_rx_dv1(gmii_rx_dv1), .gmii_rx_er1(gmii_rx_er1), `endif // !`ifdef // Time .pps(pps),.pps_select(pps_select), .pps_out_enb(pps_out_enb), // GPS Signals .gps_txd(GPS_SER_IN), .gps_rxd(GPS_SER_OUT), // Debug UART .debug_rxd(debug_rxd), .debug_txd(debug_txd), // Misc. .led_misc(leds), .debug0(), .debug1(), .debug2(), `ifndef NO_DRAM_FIFOS // DRAM signals. .ddr3_axi_clk (ddr3_axi_clk), .ddr3_axi_rst (ddr3_axi_rst), .ddr3_running (ddr3_running), // Slave Interface Write Address Ports .ddr3_axi_awid (s_axi_awid), .ddr3_axi_awaddr (s_axi_awaddr), .ddr3_axi_awlen (s_axi_awlen), .ddr3_axi_awsize (s_axi_awsize), .ddr3_axi_awburst (s_axi_awburst), .ddr3_axi_awlock (s_axi_awlock), .ddr3_axi_awcache (s_axi_awcache), .ddr3_axi_awprot (s_axi_awprot), .ddr3_axi_awqos (s_axi_awqos), .ddr3_axi_awvalid (s_axi_awvalid), .ddr3_axi_awready (s_axi_awready), // Slave Interface Write Data Ports .ddr3_axi_wdata (s_axi_wdata), .ddr3_axi_wstrb (s_axi_wstrb), .ddr3_axi_wlast (s_axi_wlast), .ddr3_axi_wvalid (s_axi_wvalid), .ddr3_axi_wready (s_axi_wready), // Slave Interface Write Response Ports .ddr3_axi_bid (s_axi_bid), .ddr3_axi_bresp (s_axi_bresp), .ddr3_axi_bvalid (s_axi_bvalid), .ddr3_axi_bready (s_axi_bready), // Slave Interface Read Address Ports .ddr3_axi_arid (s_axi_arid), .ddr3_axi_araddr (s_axi_araddr), .ddr3_axi_arlen (s_axi_arlen), .ddr3_axi_arsize (s_axi_arsize), .ddr3_axi_arburst (s_axi_arburst), .ddr3_axi_arlock (s_axi_arlock), .ddr3_axi_arcache (s_axi_arcache), .ddr3_axi_arprot (s_axi_arprot), .ddr3_axi_arqos (s_axi_arqos), .ddr3_axi_arvalid (s_axi_arvalid), .ddr3_axi_arready (s_axi_arready), // Slave Interface Read Data Ports .ddr3_axi_rid (s_axi_rid), .ddr3_axi_rdata (s_axi_rdata), .ddr3_axi_rresp (s_axi_rresp), .ddr3_axi_rlast (s_axi_rlast), .ddr3_axi_rvalid (s_axi_rvalid), .ddr3_axi_rready (s_axi_rready), `endif // `ifndef NO_DRAM_FIFOS // IoPort2 Message FIFOs .o_iop2_msg_tdata (o_iop2_msg_tdata), .o_iop2_msg_tvalid (o_iop2_msg_tvalid), .o_iop2_msg_tlast (o_iop2_msg_tlast), .o_iop2_msg_tready (o_iop2_msg_tready), .i_iop2_msg_tdata (i_iop2_msg_tdata), .i_iop2_msg_tvalid (i_iop2_msg_tvalid), .i_iop2_msg_tlast (i_iop2_msg_tlast), .i_iop2_msg_tready (i_iop2_msg_tready), // PCIe DMA Data .pcio_tdata (dmarx_tdata), .pcio_tlast (dmarx_tlast), .pcio_tvalid (dmarx_tvalid), .pcio_tready (dmarx_tready), .pcii_tdata (dmatx_tdata), .pcii_tlast (dmatx_tlast), .pcii_tvalid (dmatx_tvalid), .pcii_tready (dmatx_tready) ); endmodule // x300