From ac41c5a7adaf7f004c535b3a8b13aa5343562f50 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Mon, 6 Dec 2010 11:23:55 -0800
Subject: should safely delay the late signal which was causing timing problems
---
usrp2/vrt/vita_tx_control.v | 18 ++++++++++++++++--
1 file changed, 16 insertions(+), 2 deletions(-)
(limited to 'usrp2')
diff --git a/usrp2/vrt/vita_tx_control.v b/usrp2/vrt/vita_tx_control.v
index 20ad6b995..ab6da8bd0 100644
--- a/usrp2/vrt/vita_tx_control.v
+++ b/usrp2/vrt/vita_tx_control.v
@@ -40,7 +40,21 @@ module vita_tx_control
time_compare
time_compare (.time_now(vita_time), .trigger_time(send_time),
.now(now), .early(early), .late(late), .too_early());
+
+ reg late_qual, late_del;
+
+ always @(posedge clk)
+ if(reset | clear)
+ late_del <= 0;
+ else
+ late_del <= late;
+ always @(posedge clk)
+ if(reset | clear)
+ late_qual <= 0;
+ else
+ late_qual <= (sample_fifo_src_rdy_i & ~sample_fifo_dst_rdy_o);
+
localparam IBS_IDLE = 0;
localparam IBS_RUN = 1; // FIXME do we need this?
localparam IBS_CONT_BURST = 2;
@@ -87,7 +101,7 @@ module vita_tx_control
end
else if(~send_at | now)
ibs_state <= IBS_RUN;
- else if(late | too_early)
+ else if((late_qual & late_del) | too_early)
begin
ibs_state <= IBS_ERROR;
error_code <= CODE_TIME_ERROR;
@@ -166,7 +180,7 @@ module vita_tx_control
else
packet_consumed <= eop & sample_fifo_src_rdy_i & sample_fifo_dst_rdy_o;
- assign debug = { { now,early,late,ack,eop,eob,sob,send_at },
+ assign debug = { { now,late_qual,late_del,ack,eop,eob,sob,send_at },
{ sample_fifo_src_rdy_i, sample_fifo_dst_rdy_o, strobe, run, error, ibs_state[2:0] },
{ 8'b0 },
{ 8'b0 } };
--
cgit v1.2.3
From 355382f4c687f5d997f4589a34915d6e465bd387 Mon Sep 17 00:00:00 2001
From: Nick Foster <nick@nerdnetworks.org>
Date: Mon, 6 Dec 2010 19:41:44 -0800
Subject: u2plus: clock lock pin capitalization fail
---
usrp2/top/u2plus/u2plus.ucf | 2 +-
usrp2/top/u2plus/u2plus.v | 2 +-
2 files changed, 2 insertions(+), 2 deletions(-)
(limited to 'usrp2')
diff --git a/usrp2/top/u2plus/u2plus.ucf b/usrp2/top/u2plus/u2plus.ucf
index 25267a67e..5fbe55c26 100755
--- a/usrp2/top/u2plus/u2plus.ucf
+++ b/usrp2/top/u2plus/u2plus.ucf
@@ -158,7 +158,7 @@ NET "RXD<2>" LOC = "AF15" ;
NET "RXD<1>" LOC = "AD12" ;
## AD9510
-NET "CLK_STATUS" LOC = "AD22" ;
+NET "clk_status" LOC = "AD22" ;
NET "CLK_FUNC" LOC = "AC21" ;
NET "clk_sel<0>" LOC = "AE21" ;
NET "clk_sel<1>" LOC = "AD21" ;
diff --git a/usrp2/top/u2plus/u2plus.v b/usrp2/top/u2plus/u2plus.v
index 270655a8d..5facca298 100644
--- a/usrp2/top/u2plus/u2plus.v
+++ b/usrp2/top/u2plus/u2plus.v
@@ -44,7 +44,7 @@ module u2plus
output [1:0] clk_en,
output [1:0] clk_sel,
input CLK_FUNC, // FIXME is an input to control the 9510
- input CLK_STATUS,
+ input clk_status,
inout SCL, inout SDA, // I2C
--
cgit v1.2.3
From 4b7e1098bcbc4577b56149f0d09abaf38797dc09 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Thu, 9 Dec 2010 16:31:48 -0800
Subject: renamed exp_pps_* to be exp_time_*, which is the mimo synchronization
signal
---
usrp2/top/u2_rev3/u2_core_udp.v | 4 ++--
usrp2/top/u2_rev3/u2_rev3.ucf | 8 ++++----
usrp2/top/u2_rev3/u2_rev3.v | 24 ++++++++++++------------
usrp2/top/u2plus/u2plus.v | 4 ++--
usrp2/top/u2plus/u2plus_core.v | 4 ++--
5 files changed, 22 insertions(+), 22 deletions(-)
(limited to 'usrp2')
diff --git a/usrp2/top/u2_rev3/u2_core_udp.v b/usrp2/top/u2_rev3/u2_core_udp.v
index 9e62ee1cc..c2d473650 100644
--- a/usrp2/top/u2_rev3/u2_core_udp.v
+++ b/usrp2/top/u2_rev3/u2_core_udp.v
@@ -17,8 +17,8 @@ module u2_core
output [1:0] debug_clk,
// Expansion
- input exp_pps_in,
- output exp_pps_out,
+ input exp_time_in,
+ output exp_time_out,
// GMII
// GMII-CTRL
diff --git a/usrp2/top/u2_rev3/u2_rev3.ucf b/usrp2/top/u2_rev3/u2_rev3.ucf
index 6e0caedd5..8017f61ff 100644
--- a/usrp2/top/u2_rev3/u2_rev3.ucf
+++ b/usrp2/top/u2_rev3/u2_rev3.ucf
@@ -40,10 +40,10 @@ NET "debug_clk[0]" LOC = "N4" ;
NET "debug_clk[1]" LOC = "M1" ;
NET "uart_tx_o" LOC = "C7" ;
NET "uart_rx_i" LOC = "A3" ;
-NET "exp_pps_in_p" LOC = "V3" ;
-NET "exp_pps_in_n" LOC = "V4" ;
-NET "exp_pps_out_p" LOC = "V1" ;
-NET "exp_pps_out_n" LOC = "V2" ;
+NET "exp_time_in_p" LOC = "V3" ;
+NET "exp_time_in_n" LOC = "V4" ;
+NET "exp_time_out_p" LOC = "V1" ;
+NET "exp_time_out_n" LOC = "V2" ;
NET "GMII_COL" LOC = "U16" ;
NET "GMII_CRS" LOC = "U17" ;
NET "GMII_TXD[0]" LOC = "W14" |IOSTANDARD = LVCMOS25 |DRIVE = 12 |SLEW = FAST ;
diff --git a/usrp2/top/u2_rev3/u2_rev3.v b/usrp2/top/u2_rev3/u2_rev3.v
index 4f7f9bf1a..f2bba6c50 100644
--- a/usrp2/top/u2_rev3/u2_rev3.v
+++ b/usrp2/top/u2_rev3/u2_rev3.v
@@ -11,10 +11,10 @@ module u2_rev3
input uart_rx_i,
// Expansion
- input exp_pps_in_p, // Diff
- input exp_pps_in_n, // Diff
- output exp_pps_out_p, // Diff
- output exp_pps_out_n, // Diff
+ input exp_time_in_p, // Diff
+ input exp_time_in_n, // Diff
+ output exp_time_out_p, // Diff
+ output exp_time_out_n, // Diff
// GMII
// GMII-CTRL
@@ -181,13 +181,13 @@ module u2_rev3
wire cpld_clock_buf;
BUFG cpld_clock_BUF (.O(cpld_clock_buf),.I(cpld_clock));
- wire exp_pps_in;
- IBUFDS exp_pps_in_pin (.O(exp_pps_in),.I(exp_pps_in_p),.IB(exp_pps_in_n));
- defparam exp_pps_in_pin.IOSTANDARD = "LVDS_25";
+ wire exp_time_in;
+ IBUFDS exp_time_in_pin (.O(exp_time_in),.I(exp_time_in_p),.IB(exp_time_in_n));
+ defparam exp_time_in_pin.IOSTANDARD = "LVDS_25";
- wire exp_pps_out;
- OBUFDS exp_pps_out_pin (.O(exp_pps_out_p),.OB(exp_pps_out_n),.I(exp_pps_out));
- defparam exp_pps_out_pin.IOSTANDARD = "LVDS_25";
+ wire exp_time_out;
+ OBUFDS exp_time_out_pin (.O(exp_time_out_p),.OB(exp_time_out_n),.I(exp_time_out));
+ defparam exp_time_out_pin.IOSTANDARD = "LVDS_25";
reg [5:0] clock_ready_d;
always @(posedge clk_fpga)
@@ -480,8 +480,8 @@ module u2_rev3
.leds (leds_int),
.debug (debug[31:0]),
.debug_clk (debug_clk[1:0]),
- .exp_pps_in (exp_pps_in),
- .exp_pps_out (exp_pps_out),
+ .exp_time_in (exp_time_in),
+ .exp_time_out (exp_time_out),
.GMII_COL (GMII_COL),
.GMII_CRS (GMII_CRS),
.GMII_TXD (GMII_TXD_unreg[7:0]),
diff --git a/usrp2/top/u2plus/u2plus.v b/usrp2/top/u2plus/u2plus.v
index 5facca298..c0140e989 100644
--- a/usrp2/top/u2plus/u2plus.v
+++ b/usrp2/top/u2plus/u2plus.v
@@ -357,8 +357,8 @@ module u2plus
.leds (leds_int),
.debug (debug[31:0]),
.debug_clk (debug_clk[1:0]),
- .exp_pps_in (exp_time_in),
- .exp_pps_out (exp_time_out),
+ .exp_time_in (exp_time_in),
+ .exp_time_out (exp_time_out),
.GMII_COL (GMII_COL),
.GMII_CRS (GMII_CRS),
.GMII_TXD (GMII_TXD_unreg[7:0]),
diff --git a/usrp2/top/u2plus/u2plus_core.v b/usrp2/top/u2plus/u2plus_core.v
index 8426826e2..bce38fc73 100644
--- a/usrp2/top/u2plus/u2plus_core.v
+++ b/usrp2/top/u2plus/u2plus_core.v
@@ -16,8 +16,8 @@ module u2plus_core
output [1:0] debug_clk,
// Expansion
- input exp_pps_in,
- output exp_pps_out,
+ input exp_time_in,
+ output exp_time_out,
// GMII
// GMII-CTRL
--
cgit v1.2.3
From 8fbedd86500a9d8603ec104369fc3afd833ea2ca Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Thu, 9 Dec 2010 18:28:00 -0800
Subject: reimplemented mimo time transfer to handle 64 bits. Still needs to
sync on the received side.
---
usrp2/timing/time_64bit.v | 42 +++++++++++++++---
usrp2/timing/time_receiver.v | 96 +++++++++++++++++++++++++++--------------
usrp2/timing/time_sender.v | 68 +++++++++++++++++++++--------
usrp2/timing/time_transfer_tb.v | 26 +++++------
usrp2/top/u2plus/u2plus_core.v | 3 +-
5 files changed, 164 insertions(+), 71 deletions(-)
(limited to 'usrp2')
diff --git a/usrp2/timing/time_64bit.v b/usrp2/timing/time_64bit.v
index 51c006962..1889e73da 100644
--- a/usrp2/timing/time_64bit.v
+++ b/usrp2/timing/time_64bit.v
@@ -3,12 +3,13 @@
module time_64bit
#(parameter TICKS_PER_SEC = 32'd100000000,
parameter BASE = 0)
- (input clk, input rst,
- input set_stb, input [7:0] set_addr, input [31:0] set_data,
- input pps,
- output [63:0] vita_time, output pps_int
- );
-
+ (input clk, input rst,
+ input set_stb, input [7:0] set_addr, input [31:0] set_data,
+ input pps,
+ output [63:0] vita_time, output pps_int,
+ input exp_time_in, output exp_time_out
+ );
+
localparam NEXT_SECS = 0;
localparam NEXT_TICKS = 1;
localparam PPS_POLSRC = 2;
@@ -91,5 +92,34 @@ module time_64bit
ticks <= ticks_plus_one;
assign pps_int = pps_edge;
+
+ localparam SYNC_RATE = 59999; // Send every 600uS
+ reg [15:0] sync_counter;
+ wire send_sync = (sync_counter == SYNC_RATE);
+ wire sync_rcvd;
+
+ always @(posedge clk)
+ if(rst)
+ sync_counter <= 0;
+ else
+ if(send_sync)
+ sync_counter <= 0;
+ else
+ sync_counter <= sync_counter + 1;
+
+ // must be greater than 1000, 1 less than a multiple of 10;
+
+ time_sender time_sender
+ (.clk(clk),.rst(rst),
+ .vita_time(vita_time),
+ .send_sync(send_sync),
+ .exp_pps_out(exp_pps_out) );
+
+ time_receiver time_receiver
+ (.clk(clk),.rst(rst),
+ .vita_time(vita_time_rcvd),
+ .sync_rcvd(sync_rcvd),
+ .exp_pps_in(exp_pps_in) );
+
endmodule // time_64bit
diff --git a/usrp2/timing/time_receiver.v b/usrp2/timing/time_receiver.v
index 8e7d3f1ea..71f0ace90 100644
--- a/usrp2/timing/time_receiver.v
+++ b/usrp2/timing/time_receiver.v
@@ -1,9 +1,9 @@
module time_receiver
(input clk, input rst,
- output [31:0] master_time,
+ output reg [63:0] vita_time,
output sync_rcvd,
- input exp_pps_in);
+ input exp_time_in);
wire code_err, disp_err, dispout, complete_word;
reg disp_reg;
@@ -13,7 +13,7 @@ module time_receiver
reg [8:0] dataout_reg;
always @(posedge clk)
- shiftreg <= {exp_pps_in, shiftreg[9:1]};
+ shiftreg <= {exp_time_in, shiftreg[9:1]};
localparam COMMA_0 = 10'h283;
localparam COMMA_1 = 10'h17c;
@@ -55,40 +55,72 @@ module time_receiver
localparam STATE_T1 = 2;
localparam STATE_T2 = 3;
localparam STATE_T3 = 4;
+ localparam STATE_T4 = 5;
+ localparam STATE_T5 = 6;
+ localparam STATE_T6 = 7;
+ localparam STATE_T7 = 8;
+ localparam STATE_TAIL = 9;
localparam HEAD = 9'h13c;
-
- reg [7:0] clock_a, clock_b, clock_c;
- reg [2:0] state;
+ localparam TAIL = 9'h1F7;
+
+ reg [3:0] state;
always @(posedge clk)
if(rst)
state <= STATE_IDLE;
else if(complete_word)
- case(state)
- STATE_IDLE :
- if(dataout_reg == HEAD)
- state <= STATE_T0;
- STATE_T0 :
- begin
- clock_a <= dataout_reg[7:0];
- state <= STATE_T1;
- end
- STATE_T1 :
- begin
- clock_b <= dataout_reg[7:0];
- state <= STATE_T2;
- end
- STATE_T2 :
- begin
- clock_c <= dataout_reg[7:0];
- state <= STATE_T3;
- end
- STATE_T3 :
- state <= STATE_IDLE;
- endcase // case(state)
-
- assign master_time = {clock_a, clock_b, clock_c, dataout_reg[7:0]};
- assign sync_rcvd = (complete_word & (state == STATE_T3));
-
+ if(code_err | disp_err)
+ state <= STATE_IDLE;
+ else
+ case(state)
+ STATE_IDLE :
+ if(dataout_reg == HEAD)
+ state <= STATE_T0;
+ STATE_T0 :
+ begin
+ vita_time[63:56] <= dataout_reg[7:0];
+ state <= STATE_T1;
+ end
+ STATE_T1 :
+ begin
+ vita_time[55:48] <= dataout_reg[7:0];
+ state <= STATE_T2;
+ end
+ STATE_T2 :
+ begin
+ vita_time[47:40] <= dataout_reg[7:0];
+ state <= STATE_T3;
+ end
+ STATE_T3 :
+ begin
+ vita_time[39:32] <= dataout_reg[7:0];
+ state <= STATE_T4;
+ end
+ STATE_T4 :
+ begin
+ vita_time[31:24] <= dataout_reg[7:0];
+ state <= STATE_T5;
+ end
+ STATE_T5 :
+ begin
+ vita_time[23:16] <= dataout_reg[7:0];
+ state <= STATE_T6;
+ end
+ STATE_T6 :
+ begin
+ vita_time[15:8] <= dataout_reg[7:0];
+ state <= STATE_T7;
+ end
+ STATE_T7 :
+ begin
+ vita_time[7:0] <= dataout_reg[7:0];
+ state <= STATE_TAIL;
+ end
+ STATE_TAIL :
+ state <= STATE_IDLE;
+ endcase // case(state)
+
+ assign sync_rcvd = (complete_word & (state == STATE_TAIL) & (dataout_reg[8:0] == TAIL));
+
endmodule // time_sender
diff --git a/usrp2/timing/time_sender.v b/usrp2/timing/time_sender.v
index aa2fcbbdb..f4ee5226a 100644
--- a/usrp2/timing/time_sender.v
+++ b/usrp2/timing/time_sender.v
@@ -2,23 +2,23 @@
module time_sender
(input clk, input rst,
- input [31:0] master_time,
+ input [63:0] vita_time,
input send_sync,
- output exp_pps_out);
+ output reg exp_time_out);
reg [7:0] datain;
reg k;
wire [9:0] dataout;
- reg [9:0] dataout_reg;
- reg disp_reg;
- wire disp, new_word;
+ reg [9:0] dataout_reg;
+ reg disp_reg;
+ wire disp, new_word;
+ reg [4:0] state;
+ reg [3:0] bit_count;
encode_8b10b encode_8b10b
(.datain({k,datain}),.dispin(disp_reg),
.dataout(dataout),.dispout(disp));
- assign exp_pps_out = dataout_reg[0];
-
always @(posedge clk)
if(rst)
disp_reg <= 0;
@@ -33,9 +33,9 @@ module time_sender
else
dataout_reg <= {1'b0,dataout_reg[9:1]};
- reg [4:0] state;
- reg [3:0] bit_count;
-
+ always @(posedge clk)
+ exp_time_out <= dataout_reg[0];
+
assign new_word = (bit_count == 9);
always @(posedge clk)
@@ -52,17 +52,23 @@ module time_sender
localparam SEND_T1 = 3;
localparam SEND_T2 = 4;
localparam SEND_T3 = 5;
+ localparam SEND_T4 = 6;
+ localparam SEND_T5 = 7;
+ localparam SEND_T6 = 8;
+ localparam SEND_T7 = 9;
+ localparam SEND_TAIL = 10;
localparam COMMA = 8'hBC;
localparam HEAD = 8'h3C;
-
- reg [31:0] master_time_reg;
+ localparam TAIL = 8'hF7;
+
+ reg [63:0] vita_time_reg;
always @(posedge clk)
if(rst)
- master_time_reg <= 0;
+ vita_time_reg <= 0;
else if(send_sync)
- master_time_reg <= master_time;
+ vita_time_reg <= vita_time;
always @(posedge clk)
if(rst)
@@ -84,27 +90,51 @@ module time_sender
end
SEND_T0 :
begin
- {k,datain} <= {1'b0, master_time_reg[31:24] };
+ {k,datain} <= {1'b0, vita_time_reg[63:56] };
state <= SEND_T1;
end
SEND_T1 :
begin
- {k,datain} <= {1'b0, master_time_reg[23:16]};
+ {k,datain} <= {1'b0, vita_time_reg[55:48]};
state <= SEND_T2;
end
SEND_T2 :
begin
- {k,datain} <= {1'b0, master_time_reg[15:8]};
+ {k,datain} <= {1'b0, vita_time_reg[47:40]};
state <= SEND_T3;
end
SEND_T3 :
begin
- {k,datain} <= {1'b0, master_time_reg[7:0]};
+ {k,datain} <= {1'b0, vita_time_reg[39:32]};
+ state <= SEND_T4;
+ end
+ SEND_T4 :
+ begin
+ {k,datain} <= {1'b0, vita_time_reg[31:24]};
+ state <= SEND_T5;
+ end
+ SEND_T5 :
+ begin
+ {k,datain} <= {1'b0, vita_time_reg[23:16]};
+ state <= SEND_T6;
+ end
+ SEND_T6 :
+ begin
+ {k,datain} <= {1'b0, vita_time_reg[15:8]};
+ state <= SEND_T7;
+ end
+ SEND_T7 :
+ begin
+ {k,datain} <= {1'b0, vita_time_reg[7:0]};
+ state <= SEND_TAIL;
+ end
+ SEND_TAIL :
+ begin
+ {k,datain} <= {1'b1, TAIL};
state <= SEND_IDLE;
end
default :
state <= SEND_IDLE;
endcase // case(state)
-
endmodule // time_sender
diff --git a/usrp2/timing/time_transfer_tb.v b/usrp2/timing/time_transfer_tb.v
index 2b75c60bd..0c164f82c 100644
--- a/usrp2/timing/time_transfer_tb.v
+++ b/usrp2/timing/time_transfer_tb.v
@@ -18,12 +18,12 @@ module time_transfer_tb();
initial #100000000 $finish;
- wire exp_pps, pps, pps_rcv;
- wire [31:0] master_clock_rcv;
- reg [31:0] master_clock = 0;
- reg [31:0] counter = 0;
+ wire exp_time, pps, pps_rcv;
+ wire [63:0] vita_time_rcv;
+ reg [63:0] vita_time = 0;
+ reg [63:0] counter = 0;
- localparam PPS_PERIOD = 109;
+ localparam PPS_PERIOD = 439; // PPS_PERIOD % 10 must = 9
always @(posedge clk)
if(counter == PPS_PERIOD)
counter <= 0;
@@ -32,19 +32,19 @@ module time_transfer_tb();
assign pps = (counter == (PPS_PERIOD-1));
always @(posedge clk)
- master_clock <= master_clock + 1;
+ vita_time <= vita_time + 1;
time_sender time_sender
(.clk(clk),.rst(rst),
- .master_clock(master_clock),
- .pps(pps),
- .exp_pps_out(exp_pps) );
+ .vita_time(vita_time),
+ .send_sync(pps),
+ .exp_time_out(exp_time) );
time_receiver time_receiver
(.clk(clk),.rst(rst),
- .master_clock(master_clock_rcv),
- .pps(pps_rcv),
- .exp_pps_in(exp_pps) );
+ .vita_time(vita_time_rcv),
+ .sync_rcvd(pps_rcv),
+ .exp_time_in(exp_time) );
- wire [31:0] delta = master_clock - master_clock_rcv;
+ wire [31:0] delta = vita_time - vita_time_rcv;
endmodule // time_transfer_tb
diff --git a/usrp2/top/u2plus/u2plus_core.v b/usrp2/top/u2plus/u2plus_core.v
index bce38fc73..4e0b190ef 100644
--- a/usrp2/top/u2plus/u2plus_core.v
+++ b/usrp2/top/u2plus/u2plus_core.v
@@ -683,7 +683,8 @@ module u2plus_core
time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
(.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
- .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int));
+ .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int),
+ .exp_time_in(exp_time_in), .exp_time_out(exp_time_out));
// /////////////////////////////////////////////////////////////////////////////////////////
// Debug Pins
--
cgit v1.2.3
From 3555f0498f36feae14d0bdbbe6a8ecd0db513db0 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Thu, 9 Dec 2010 23:37:52 -0800
Subject: remove old raw ethernet version
---
usrp2/top/u2_rev3/Makefile | 97 ------
usrp2/top/u2_rev3/u2_core.v | 785 --------------------------------------------
2 files changed, 882 deletions(-)
delete mode 100644 usrp2/top/u2_rev3/Makefile
delete mode 100644 usrp2/top/u2_rev3/u2_core.v
(limited to 'usrp2')
diff --git a/usrp2/top/u2_rev3/Makefile b/usrp2/top/u2_rev3/Makefile
deleted file mode 100644
index 68c296b9b..000000000
--- a/usrp2/top/u2_rev3/Makefile
+++ /dev/null
@@ -1,97 +0,0 @@
-#
-# Copyright 2008 Ettus Research LLC
-#
-
-##################################################
-# Project Setup
-##################################################
-TOP_MODULE = u2_rev3
-BUILD_DIR = $(abspath build$(ISE))
-
-##################################################
-# Include other makefiles
-##################################################
-
-include ../Makefile.common
-include ../../fifo/Makefile.srcs
-include ../../control_lib/Makefile.srcs
-include ../../sdr_lib/Makefile.srcs
-include ../../serdes/Makefile.srcs
-include ../../simple_gemac/Makefile.srcs
-include ../../timing/Makefile.srcs
-include ../../opencores/Makefile.srcs
-include ../../vrt/Makefile.srcs
-include ../../udp/Makefile.srcs
-include ../../coregen/Makefile.srcs
-include ../../extram/Makefile.srcs
-
-##################################################
-# Project Properties
-##################################################
-PROJECT_PROPERTIES = \
-family Spartan3 \
-device xc3s2000 \
-package fg456 \
-speed -5 \
-top_level_module_type "HDL" \
-synthesis_tool "XST (VHDL/Verilog)" \
-simulator "ISE Simulator (VHDL/Verilog)" \
-"Preferred Language" "Verilog" \
-"Enable Message Filtering" FALSE \
-"Display Incremental Messages" FALSE
-
-##################################################
-# Sources
-##################################################
-TOP_SRCS = \
-u2_core.v \
-u2_rev3.v \
-u2_rev3.ucf
-
-SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
-$(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
-$(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
-
-##################################################
-# Process Properties
-##################################################
-SYNTHESIZE_PROPERTIES = \
-"Number of Clock Buffers" 8 \
-"Pack I/O Registers into IOBs" Yes \
-"Optimization Effort" High \
-"Optimize Instantiated Primitives" TRUE \
-"Register Balancing" Yes \
-"Use Clock Enable" Auto \
-"Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
-
-TRANSLATE_PROPERTIES = \
-"Macro Search Path" "$(shell pwd)/../../coregen/"
-
-MAP_PROPERTIES = \
-"Allow Logic Optimization Across Hierarchy" TRUE \
-"Map to Input Functions" 4 \
-"Optimization Strategy (Cover Mode)" Speed \
-"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \
-"Perform Timing-Driven Packing and Placement" TRUE \
-"Map Effort Level" High \
-"Extra Effort" Normal \
-"Combinatorial Logic Optimization" TRUE \
-"Register Duplication" TRUE
-
-PLACE_ROUTE_PROPERTIES = \
-"Place & Route Effort Level (Overall)" High
-
-STATIC_TIMING_PROPERTIES = \
-"Number of Paths in Error/Verbose Report" 10 \
-"Report Type" "Error Report"
-
-GEN_PROG_FILE_PROPERTIES = \
-"Configuration Rate" 6 \
-"Create Binary Configuration File" TRUE \
-"Done (Output Events)" 5 \
-"Enable Bitstream Compression" TRUE \
-"Enable Outputs (Output Events)" 6
-
-SIM_MODEL_PROPERTIES = ""
diff --git a/usrp2/top/u2_rev3/u2_core.v b/usrp2/top/u2_rev3/u2_core.v
deleted file mode 100644
index a5963f6b1..000000000
--- a/usrp2/top/u2_rev3/u2_core.v
+++ /dev/null
@@ -1,785 +0,0 @@
-// ////////////////////////////////////////////////////////////////////////////////
-// Module Name: u2_core
-// ////////////////////////////////////////////////////////////////////////////////
-
-module u2_core
- #(parameter RAM_SIZE=32768)
- (// Clocks
- input dsp_clk,
- input wb_clk,
- output clock_ready,
- input clk_to_mac,
- input pps_in,
-
- // Misc, debug
- output [7:0] leds,
- output [31:0] debug,
- output [1:0] debug_clk,
-
- // Expansion
- input exp_pps_in,
- output exp_pps_out,
-
- // GMII
- // GMII-CTRL
- input GMII_COL,
- input GMII_CRS,
-
- // GMII-TX
- output [7:0] GMII_TXD,
- output GMII_TX_EN,
- output GMII_TX_ER,
- output GMII_GTX_CLK,
- input GMII_TX_CLK, // 100mbps clk
-
- // GMII-RX
- input [7:0] GMII_RXD,
- input GMII_RX_CLK,
- input GMII_RX_DV,
- input GMII_RX_ER,
-
- // GMII-Management
- inout MDIO,
- output MDC,
- input PHY_INTn, // open drain
- output PHY_RESETn,
-
- // SERDES
- output ser_enable,
- output ser_prbsen,
- output ser_loopen,
- output ser_rx_en,
-
- output ser_tx_clk,
- output [15:0] ser_t,
- output ser_tklsb,
- output ser_tkmsb,
-
- input ser_rx_clk,
- input [15:0] ser_r,
- input ser_rklsb,
- input ser_rkmsb,
-
- // CPLD interface
- output cpld_start,
- output cpld_mode,
- output cpld_done,
- input cpld_din,
- input cpld_clk,
- input cpld_detached,
- output cpld_misc,
- input cpld_init_b,
- input por,
- output config_success,
-
- // ADC
- input [13:0] adc_a,
- input adc_ovf_a,
- output adc_on_a,
- output adc_oe_a,
-
- input [13:0] adc_b,
- input adc_ovf_b,
- output adc_on_b,
- output adc_oe_b,
-
- // DAC
- output [15:0] dac_a,
- output [15:0] dac_b,
-
- // I2C
- input scl_pad_i,
- output scl_pad_o,
- output scl_pad_oen_o,
- input sda_pad_i,
- output sda_pad_o,
- output sda_pad_oen_o,
-
- // Clock Gen Control
- output [1:0] clk_en,
- output [1:0] clk_sel,
- input clk_func, // FIXME is an input to control the 9510
- input clk_status,
-
- // Generic SPI
- output sclk,
- output mosi,
- input miso,
- output sen_clk,
- output sen_dac,
- output sen_tx_db,
- output sen_tx_adc,
- output sen_tx_dac,
- output sen_rx_db,
- output sen_rx_adc,
- output sen_rx_dac,
-
- // GPIO to DBoards
- inout [15:0] io_tx,
- inout [15:0] io_rx,
-
- // External RAM
- inout [17:0] RAM_D,
- output [18:0] RAM_A,
- output RAM_CE1n,
- output RAM_CENn,
- // output RAM_CLK,
- output RAM_WEn,
- output RAM_OEn,
- output RAM_LDn,
-
- // Debug stuff
- output uart_tx_o,
- input uart_rx_i,
- output uart_baud_o,
- input sim_mode,
- input [3:0] clock_divider
- );
-
- localparam SR_BUF_POOL = 64; // Uses 1 reg
- localparam SR_UDP_SM = 96; // 64 regs
- localparam SR_RX_DSP = 160; // 16
- localparam SR_RX_CTRL = 176; // 16
- localparam SR_TIME64 = 192; // 3
- localparam SR_SIMTIMER = 198; // 2
- localparam SR_TX_DSP = 128; // 16
- localparam SR_TX_CTRL = 224; // 16
-
- // FIFO Sizes, 9 = 512 lines, 10 = 1024, 11 = 2048
- // all (most?) are 36 bits wide, so 9 is 1 BRAM, 10 is 2, 11 is 4 BRAMs
- localparam DSP_TX_FIFOSIZE = 10;
- localparam DSP_RX_FIFOSIZE = 10;
- localparam ETH_TX_FIFOSIZE = 10;
- localparam ETH_RX_FIFOSIZE = 11;
- localparam SERDES_TX_FIFOSIZE = 9;
- localparam SERDES_RX_FIFOSIZE = 9; // RX currently doesn't use a fifo?
-
- wire [7:0] set_addr, set_addr_dsp;
- wire [31:0] set_data, set_data_dsp;
- wire set_stb, set_stb_dsp;
-
- wire ram_loader_done;
- wire ram_loader_rst, wb_rst, dsp_rst;
-
- wire [31:0] status, status_b0, status_b1, status_b2, status_b3, status_b4, status_b5, status_b6, status_b7;
- wire bus_error, spi_int, i2c_int, pps_int, timer_int, buffer_int, proc_int, overrun, underrun, uart_tx_int, uart_rx_int;
-
- wire [31:0] debug_gpio_0, debug_gpio_1;
- wire [31:0] atr_lines;
-
- wire [31:0] debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc,
- debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp;
-
- wire [15:0] ser_rx_occ, ser_tx_occ, dsp_rx_occ, dsp_tx_occ, eth_rx_occ, eth_tx_occ, eth_rx_occ2;
- wire ser_rx_full, ser_tx_full, dsp_rx_full, dsp_tx_full, eth_rx_full, eth_tx_full, eth_rx_full2;
- wire ser_rx_empty, ser_tx_empty, dsp_rx_empty, dsp_tx_empty, eth_rx_empty, eth_tx_empty, eth_rx_empty2;
-
- wire serdes_link_up;
- wire epoch;
- wire [31:0] irq;
-
- // ///////////////////////////////////////////////////////////////////////////////////////////////
- // Wishbone Single Master INTERCON
- localparam dw = 32; // Data bus width
- localparam aw = 16; // Address bus width, for byte addressibility, 16 = 64K byte memory space
- localparam sw = 4; // Select width -- 32-bit data bus with 8-bit granularity.
-
- wire [dw-1:0] m0_dat_o, m0_dat_i;
- wire [dw-1:0] s0_dat_o, s1_dat_o, s0_dat_i, s1_dat_i, s2_dat_o, s3_dat_o, s2_dat_i, s3_dat_i,
- s4_dat_o, s5_dat_o, s4_dat_i, s5_dat_i, s6_dat_o, s7_dat_o, s6_dat_i, s7_dat_i,
- s8_dat_o, s9_dat_o, s8_dat_i, s9_dat_i, sa_dat_o, sa_dat_i, sb_dat_i, sb_dat_o,
- sc_dat_i, sc_dat_o, sd_dat_i, sd_dat_o, se_dat_i, se_dat_o;
- wire [aw-1:0] m0_adr,s0_adr,s1_adr,s2_adr,s3_adr,s4_adr,s5_adr,s6_adr,s7_adr,s8_adr,s9_adr,sa_adr,sb_adr,sc_adr, sd_adr, se_adr;
- wire [sw-1:0] m0_sel,s0_sel,s1_sel,s2_sel,s3_sel,s4_sel,s5_sel,s6_sel,s7_sel,s8_sel,s9_sel,sa_sel,sb_sel,sc_sel, sd_sel, se_sel;
- wire m0_ack,s0_ack,s1_ack,s2_ack,s3_ack,s4_ack,s5_ack,s6_ack,s7_ack,s8_ack,s9_ack,sa_ack,sb_ack,sc_ack, sd_ack, se_ack;
- wire m0_stb,s0_stb,s1_stb,s2_stb,s3_stb,s4_stb,s5_stb,s6_stb,s7_stb,s8_stb,s9_stb,sa_stb,sb_stb,sc_stb, sd_stb, se_stb;
- wire m0_cyc,s0_cyc,s1_cyc,s2_cyc,s3_cyc,s4_cyc,s5_cyc,s6_cyc,s7_cyc,s8_cyc,s9_cyc,sa_cyc,sb_cyc,sc_cyc, sd_cyc, se_cyc;
- wire m0_err, m0_rty;
- wire m0_we,s0_we,s1_we,s2_we,s3_we,s4_we,s5_we,s6_we,s7_we,s8_we,s9_we,sa_we,sb_we,sc_we,sd_we, se_we;
-
- wb_1master #(.decode_w(6),
- .s0_addr(6'b0000_00),.s0_mask(6'b100000),
- .s1_addr(6'b1000_00),.s1_mask(6'b110000),
- .s2_addr(6'b1100_00),.s2_mask(6'b111111),
- .s3_addr(6'b1100_01),.s3_mask(6'b111111),
- .s4_addr(6'b1100_10),.s4_mask(6'b111111),
- .s5_addr(6'b1100_11),.s5_mask(6'b111111),
- .s6_addr(6'b1101_00),.s6_mask(6'b111111),
- .s7_addr(6'b1101_01),.s7_mask(6'b111111),
- .s8_addr(6'b1101_10),.s8_mask(6'b111111),
- .s9_addr(6'b1101_11),.s9_mask(6'b111111),
- .sa_addr(6'b1110_00),.sa_mask(6'b111111),
- .sb_addr(6'b1110_01),.sb_mask(6'b111111),
- .sc_addr(6'b1110_10),.sc_mask(6'b111111),
- .sd_addr(6'b1110_11),.sd_mask(6'b111111),
- .se_addr(6'b1111_00),.se_mask(6'b111111),
- .sf_addr(6'b1111_01),.sf_mask(6'b111111),
- .dw(dw),.aw(aw),.sw(sw)) wb_1master
- (.clk_i(wb_clk),.rst_i(wb_rst),
- .m0_dat_o(m0_dat_o),.m0_ack_o(m0_ack),.m0_err_o(m0_err),.m0_rty_o(m0_rty),.m0_dat_i(m0_dat_i),
- .m0_adr_i(m0_adr),.m0_sel_i(m0_sel),.m0_we_i(m0_we),.m0_cyc_i(m0_cyc),.m0_stb_i(m0_stb),
- .s0_dat_o(s0_dat_o),.s0_adr_o(s0_adr),.s0_sel_o(s0_sel),.s0_we_o (s0_we),.s0_cyc_o(s0_cyc),.s0_stb_o(s0_stb),
- .s0_dat_i(s0_dat_i),.s0_ack_i(s0_ack),.s0_err_i(0),.s0_rty_i(0),
- .s1_dat_o(s1_dat_o),.s1_adr_o(s1_adr),.s1_sel_o(s1_sel),.s1_we_o (s1_we),.s1_cyc_o(s1_cyc),.s1_stb_o(s1_stb),
- .s1_dat_i(s1_dat_i),.s1_ack_i(s1_ack),.s1_err_i(0),.s1_rty_i(0),
- .s2_dat_o(s2_dat_o),.s2_adr_o(s2_adr),.s2_sel_o(s2_sel),.s2_we_o (s2_we),.s2_cyc_o(s2_cyc),.s2_stb_o(s2_stb),
- .s2_dat_i(s2_dat_i),.s2_ack_i(s2_ack),.s2_err_i(0),.s2_rty_i(0),
- .s3_dat_o(s3_dat_o),.s3_adr_o(s3_adr),.s3_sel_o(s3_sel),.s3_we_o (s3_we),.s3_cyc_o(s3_cyc),.s3_stb_o(s3_stb),
- .s3_dat_i(s3_dat_i),.s3_ack_i(s3_ack),.s3_err_i(0),.s3_rty_i(0),
- .s4_dat_o(s4_dat_o),.s4_adr_o(s4_adr),.s4_sel_o(s4_sel),.s4_we_o (s4_we),.s4_cyc_o(s4_cyc),.s4_stb_o(s4_stb),
- .s4_dat_i(s4_dat_i),.s4_ack_i(s4_ack),.s4_err_i(0),.s4_rty_i(0),
- .s5_dat_o(s5_dat_o),.s5_adr_o(s5_adr),.s5_sel_o(s5_sel),.s5_we_o (s5_we),.s5_cyc_o(s5_cyc),.s5_stb_o(s5_stb),
- .s5_dat_i(s5_dat_i),.s5_ack_i(s5_ack),.s5_err_i(0),.s5_rty_i(0),
- .s6_dat_o(s6_dat_o),.s6_adr_o(s6_adr),.s6_sel_o(s6_sel),.s6_we_o (s6_we),.s6_cyc_o(s6_cyc),.s6_stb_o(s6_stb),
- .s6_dat_i(s6_dat_i),.s6_ack_i(s6_ack),.s6_err_i(0),.s6_rty_i(0),
- .s7_dat_o(s7_dat_o),.s7_adr_o(s7_adr),.s7_sel_o(s7_sel),.s7_we_o (s7_we),.s7_cyc_o(s7_cyc),.s7_stb_o(s7_stb),
- .s7_dat_i(s7_dat_i),.s7_ack_i(s7_ack),.s7_err_i(0),.s7_rty_i(0),
- .s8_dat_o(s8_dat_o),.s8_adr_o(s8_adr),.s8_sel_o(s8_sel),.s8_we_o (s8_we),.s8_cyc_o(s8_cyc),.s8_stb_o(s8_stb),
- .s8_dat_i(s8_dat_i),.s8_ack_i(s8_ack),.s8_err_i(0),.s8_rty_i(0),
- .s9_dat_o(s9_dat_o),.s9_adr_o(s9_adr),.s9_sel_o(s9_sel),.s9_we_o (s9_we),.s9_cyc_o(s9_cyc),.s9_stb_o(s9_stb),
- .s9_dat_i(s9_dat_i),.s9_ack_i(s9_ack),.s9_err_i(0),.s9_rty_i(0),
- .sa_dat_o(sa_dat_o),.sa_adr_o(sa_adr),.sa_sel_o(sa_sel),.sa_we_o(sa_we),.sa_cyc_o(sa_cyc),.sa_stb_o(sa_stb),
- .sa_dat_i(sa_dat_i),.sa_ack_i(sa_ack),.sa_err_i(0),.sa_rty_i(0),
- .sb_dat_o(sb_dat_o),.sb_adr_o(sb_adr),.sb_sel_o(sb_sel),.sb_we_o(sb_we),.sb_cyc_o(sb_cyc),.sb_stb_o(sb_stb),
- .sb_dat_i(sb_dat_i),.sb_ack_i(sb_ack),.sb_err_i(0),.sb_rty_i(0),
- .sc_dat_o(sc_dat_o),.sc_adr_o(sc_adr),.sc_sel_o(sc_sel),.sc_we_o(sc_we),.sc_cyc_o(sc_cyc),.sc_stb_o(sc_stb),
- .sc_dat_i(sc_dat_i),.sc_ack_i(sc_ack),.sc_err_i(0),.sc_rty_i(0),
- .sd_dat_o(sd_dat_o),.sd_adr_o(sd_adr),.sd_sel_o(sd_sel),.sd_we_o(sd_we),.sd_cyc_o(sd_cyc),.sd_stb_o(sd_stb),
- .sd_dat_i(sd_dat_i),.sd_ack_i(sd_ack),.sd_err_i(0),.sd_rty_i(0),
- .se_dat_o(se_dat_o),.se_adr_o(se_adr),.se_sel_o(se_sel),.se_we_o(se_we),.se_cyc_o(se_cyc),.se_stb_o(se_stb),
- .se_dat_i(se_dat_i),.se_ack_i(se_ack),.se_err_i(0),.se_rty_i(0),
- .sf_dat_i(0),.sf_ack_i(0),.sf_err_i(0),.sf_rty_i(0) );
-
- //////////////////////////////////////////////////////////////////////////////////////////
- // Reset Controller
- system_control sysctrl (.wb_clk_i(wb_clk), // .por_i(por),
- .ram_loader_rst_o(ram_loader_rst),
- .wb_rst_o(wb_rst),
- .ram_loader_done_i(ram_loader_done));
-
- assign config_success = ram_loader_done;
- reg takeover = 0;
-
- wire cpld_start_int, cpld_mode_int, cpld_done_int;
-
- always @(posedge wb_clk)
- if(ram_loader_done)
- takeover = 1;
- assign cpld_misc = ~takeover;
-
- wire sd_clk, sd_csn, sd_mosi, sd_miso;
-
- assign sd_miso = cpld_din;
- assign cpld_start = takeover ? sd_clk : cpld_start_int;
- assign cpld_mode = takeover ? sd_csn : cpld_mode_int;
- assign cpld_done = takeover ? sd_mosi : cpld_done_int;
-
- // ///////////////////////////////////////////////////////////////////
- // RAM Loader
-
- wire [31:0] ram_loader_dat, if_dat;
- wire [15:0] ram_loader_adr;
- wire [14:0] if_adr;
- wire [3:0] ram_loader_sel;
- wire ram_loader_stb, ram_loader_we;
- wire iwb_ack, iwb_stb;
- ram_loader #(.AWIDTH(16),.RAM_SIZE(RAM_SIZE))
- ram_loader (.wb_clk(wb_clk),.dsp_clk(dsp_clk),.ram_loader_rst(ram_loader_rst),
- .wb_dat(ram_loader_dat),.wb_adr(ram_loader_adr),
- .wb_stb(ram_loader_stb),.wb_sel(ram_loader_sel),
- .wb_we(ram_loader_we),
- .ram_loader_done(ram_loader_done),
- // CPLD Interface
- .cpld_clk(cpld_clk),
- .cpld_din(cpld_din),
- .cpld_start(cpld_start_int),
- .cpld_mode(cpld_mode_int),
- .cpld_done(cpld_done_int),
- .cpld_detached(cpld_detached));
-
- // /////////////////////////////////////////////////////////////////////////
- // Processor
- aeMB_core_BE #(.ISIZ(16),.DSIZ(16),.MUL(0),.BSF(1))
- aeMB (.sys_clk_i(wb_clk), .sys_rst_i(wb_rst),
- // Instruction Wishbone bus to I-RAM
- .if_adr(if_adr),
- .if_dat(if_dat),
- // Data Wishbone bus to system bus fabric
- .dwb_we_o(m0_we),.dwb_stb_o(m0_stb),.dwb_dat_o(m0_dat_i),.dwb_adr_o(m0_adr),
- .dwb_dat_i(m0_dat_o),.dwb_ack_i(m0_ack),.dwb_sel_o(m0_sel),.dwb_cyc_o(m0_cyc),
- // Interrupts and exceptions
- .sys_int_i(proc_int),.sys_exc_i(bus_error) );
-
- assign bus_error = m0_err | m0_rty;
-
- // /////////////////////////////////////////////////////////////////////////
- // Dual Ported RAM -- D-Port is Slave #0 on main Wishbone
- // I-port connects directly to processor and ram loader
-
- wire flush_icache;
- ram_harvard #(.AWIDTH(15),.RAM_SIZE(RAM_SIZE),.ICWIDTH(7),.DCWIDTH(6))
- sys_ram(.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
-
- .ram_loader_adr_i(ram_loader_adr[14:0]), .ram_loader_dat_i(ram_loader_dat),
- .ram_loader_stb_i(ram_loader_stb), .ram_loader_sel_i(ram_loader_sel),
- .ram_loader_we_i(ram_loader_we),
- .ram_loader_done_i(ram_loader_done),
-
- .if_adr(if_adr),
- .if_data(if_dat),
-
- .dwb_adr_i(s0_adr[14:0]), .dwb_dat_i(s0_dat_o), .dwb_dat_o(s0_dat_i),
- .dwb_we_i(s0_we), .dwb_ack_o(s0_ack), .dwb_stb_i(s0_stb), .dwb_sel_i(s0_sel),
- .flush_icache(flush_icache));
-
- setting_reg #(.my_addr(7)) sr_icache (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(),.changed(flush_icache));
-
- // /////////////////////////////////////////////////////////////////////////
- // Buffer Pool, slave #1
- wire rd0_ready_i, rd0_ready_o;
- wire rd1_ready_i, rd1_ready_o;
- wire rd2_ready_i, rd2_ready_o;
- wire rd3_ready_i, rd3_ready_o;
- wire [3:0] rd0_flags, rd1_flags, rd2_flags, rd3_flags;
- wire [31:0] rd0_dat, rd1_dat, rd2_dat, rd3_dat;
-
- wire wr0_ready_i, wr0_ready_o;
- wire wr1_ready_i, wr1_ready_o;
- wire wr2_ready_i, wr2_ready_o;
- wire wr3_ready_i, wr3_ready_o;
- wire [3:0] wr0_flags, wr1_flags, wr2_flags, wr3_flags;
- wire [31:0] wr0_dat, wr1_dat, wr2_dat, wr3_dat;
-
- buffer_pool #(.BUF_SIZE(9), .SET_ADDR(SR_BUF_POOL)) buffer_pool
- (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
- .wb_we_i(s1_we),.wb_stb_i(s1_stb),.wb_adr_i(s1_adr),.wb_dat_i(s1_dat_o),
- .wb_dat_o(s1_dat_i),.wb_ack_o(s1_ack),.wb_err_o(),.wb_rty_o(),
-
- .stream_clk(dsp_clk), .stream_rst(dsp_rst),
- .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
- .status(status),.sys_int_o(buffer_int),
-
- .s0(status_b0),.s1(status_b1),.s2(status_b2),.s3(status_b3),
- .s4(status_b4),.s5(status_b5),.s6(status_b6),.s7(status_b7),
-
- // Write Interfaces
- .wr0_data_i(wr0_dat), .wr0_flags_i(wr0_flags), .wr0_ready_i(wr0_ready_i), .wr0_ready_o(wr0_ready_o),
- .wr1_data_i(wr1_dat), .wr1_flags_i(wr1_flags), .wr1_ready_i(wr1_ready_i), .wr1_ready_o(wr1_ready_o),
- .wr2_data_i(wr2_dat), .wr2_flags_i(wr2_flags), .wr2_ready_i(wr2_ready_i), .wr2_ready_o(wr2_ready_o),
- .wr3_data_i(wr3_dat), .wr3_flags_i(wr3_flags), .wr3_ready_i(wr3_ready_i), .wr3_ready_o(wr3_ready_o),
- // Read Interfaces
- .rd0_data_o(rd0_dat), .rd0_flags_o(rd0_flags), .rd0_ready_i(rd0_ready_i), .rd0_ready_o(rd0_ready_o),
- .rd1_data_o(rd1_dat), .rd1_flags_o(rd1_flags), .rd1_ready_i(rd1_ready_i), .rd1_ready_o(rd1_ready_o),
- .rd2_data_o(rd2_dat), .rd2_flags_o(rd2_flags), .rd2_ready_i(rd2_ready_i), .rd2_ready_o(rd2_ready_o),
- .rd3_data_o(rd3_dat), .rd3_flags_o(rd3_flags), .rd3_ready_i(rd3_ready_i), .rd3_ready_o(rd3_ready_o)
- );
-
- wire [31:0] status_enc;
- priority_enc priority_enc (.in({16'b0,status[15:0]}), .out(status_enc));
-
- // /////////////////////////////////////////////////////////////////////////
- // SPI -- Slave #2
- spi_top shared_spi
- (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.wb_adr_i(s2_adr[4:0]),.wb_dat_i(s2_dat_o),
- .wb_dat_o(s2_dat_i),.wb_sel_i(s2_sel),.wb_we_i(s2_we),.wb_stb_i(s2_stb),
- .wb_cyc_i(s2_cyc),.wb_ack_o(s2_ack),.wb_err_o(),.wb_int_o(spi_int),
- .ss_pad_o({sen_tx_db,sen_tx_adc,sen_tx_dac,sen_rx_db,sen_rx_adc,sen_rx_dac,sen_dac,sen_clk}),
- .sclk_pad_o(sclk),.mosi_pad_o(mosi),.miso_pad_i(miso) );
-
- // /////////////////////////////////////////////////////////////////////////
- // I2C -- Slave #3
- i2c_master_top #(.ARST_LVL(1))
- i2c (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.arst_i(1'b0),
- .wb_adr_i(s3_adr[4:2]),.wb_dat_i(s3_dat_o[7:0]),.wb_dat_o(s3_dat_i[7:0]),
- .wb_we_i(s3_we),.wb_stb_i(s3_stb),.wb_cyc_i(s3_cyc),
- .wb_ack_o(s3_ack),.wb_inta_o(i2c_int),
- .scl_pad_i(scl_pad_i),.scl_pad_o(scl_pad_o),.scl_padoen_o(scl_pad_oen_o),
- .sda_pad_i(sda_pad_i),.sda_pad_o(sda_pad_o),.sda_padoen_o(sda_pad_oen_o) );
-
- assign s3_dat_i[31:8] = 24'd0;
-
- // /////////////////////////////////////////////////////////////////////////
- // GPIOs -- Slave #4
- nsgpio nsgpio(.clk_i(wb_clk),.rst_i(wb_rst),
- .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we),
- .dat_i(s4_dat_o),.dat_o(s4_dat_i),.ack_o(s4_ack),
- .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1),
- .gpio( {io_tx,io_rx} ) );
-
- // /////////////////////////////////////////////////////////////////////////
- // Buffer Pool Status -- Slave #5
-
- reg [31:0] cycle_count;
- always @(posedge wb_clk)
- if(wb_rst)
- cycle_count <= 0;
- else
- cycle_count <= cycle_count + 1;
-
- wb_readback_mux buff_pool_status
- (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
- .wb_adr_i(s5_adr), .wb_dat_o(s5_dat_i), .wb_ack_o(s5_ack),
-
- .word00(status_b0),.word01(status_b1),.word02(status_b2),.word03(status_b3),
- .word04(status_b4),.word05(status_b5),.word06(status_b6),.word07(status_b7),
- .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(32'b0),
- .word11(32'b0),.word12(32'b0),.word13(irq),.word14(status_enc),.word15(cycle_count)
- );
-
- // /////////////////////////////////////////////////////////////////////////
- // Ethernet MAC Slave #6
-
- simple_gemac_wrapper #(.RXFIFOSIZE(11), .TXFIFOSIZE(6)) simple_gemac_wrapper
- (.clk125(clk_to_mac), .reset(wb_rst),
- .GMII_GTX_CLK(GMII_GTX_CLK), .GMII_TX_EN(GMII_TX_EN),
- .GMII_TX_ER(GMII_TX_ER), .GMII_TXD(GMII_TXD),
- .GMII_RX_CLK(GMII_RX_CLK), .GMII_RX_DV(GMII_RX_DV),
- .GMII_RX_ER(GMII_RX_ER), .GMII_RXD(GMII_RXD),
- .sys_clk(dsp_clk),
- .rx_f36_data({wr2_flags,wr2_dat}), .rx_f36_src_rdy(wr2_ready_i), .rx_f36_dst_rdy(wr2_ready_o),
- .tx_f36_data({rd2_flags,rd2_dat}), .tx_f36_src_rdy(rd2_ready_o), .tx_f36_dst_rdy(rd2_ready_i),
- .wb_clk(wb_clk), .wb_rst(wb_rst), .wb_stb(s6_stb), .wb_cyc(s6_cyc), .wb_ack(s6_ack),
- .wb_we(s6_we), .wb_adr(s6_adr), .wb_dat_i(s6_dat_o), .wb_dat_o(s6_dat_i),
- .mdio(MDIO), .mdc(MDC),
- .debug(debug_mac));
-
- // /////////////////////////////////////////////////////////////////////////
- // Settings Bus -- Slave #7
- settings_bus settings_bus
- (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s7_adr),.wb_dat_i(s7_dat_o),
- .wb_stb_i(s7_stb),.wb_we_i(s7_we),.wb_ack_o(s7_ack),
- .strobe(set_stb),.addr(set_addr),.data(set_data));
-
- assign s7_dat_i = 32'd0;
-
- settings_bus_crossclock settings_bus_crossclock
- (.clk_i(wb_clk), .rst_i(wb_rst), .set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
- .clk_o(dsp_clk), .rst_o(dsp_rst), .set_stb_o(set_stb_dsp), .set_addr_o(set_addr_dsp), .set_data_o(set_data_dsp));
-
- // Output control lines
- wire [7:0] clock_outs, serdes_outs, adc_outs;
- assign {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0];
- assign {ser_enable, ser_prbsen, ser_loopen, ser_rx_en} = serdes_outs[3:0];
- assign {adc_oe_a, adc_on_a, adc_oe_b, adc_on_b } = adc_outs[3:0];
-
- wire phy_reset;
- assign PHY_RESETn = ~phy_reset;
-
- setting_reg #(.my_addr(0),.width(8)) sr_clk (.clk(wb_clk),.rst(wb_rst),.strobe(s7_ack),.addr(set_addr),
- .in(set_data),.out(clock_outs),.changed());
- setting_reg #(.my_addr(1),.width(8)) sr_ser (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(serdes_outs),.changed());
- setting_reg #(.my_addr(2),.width(8)) sr_adc (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(adc_outs),.changed());
- setting_reg #(.my_addr(4),.width(1)) sr_phy (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(phy_reset),.changed());
-
- // /////////////////////////////////////////////////////////////////////////
- // LEDS
- // register 8 determines whether leds are controlled by SW or not
- // 1 = controlled by HW, 0 = by SW
- // In Rev3 there are only 6 leds, and the highest one is on the ETH connector
-
- wire [7:0] led_src, led_sw;
- wire [7:0] led_hw = {clk_status,serdes_link_up};
-
- setting_reg #(.my_addr(3),.width(8)) sr_led (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(led_sw),.changed());
- setting_reg #(.my_addr(8),.width(8)) sr_led_src (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(led_src),.changed());
-
- assign leds = (led_src & led_hw) | (~led_src & led_sw);
-
- // /////////////////////////////////////////////////////////////////////////
- // Interrupt Controller, Slave #8
-
- assign irq= {{8'b0},
- {8'b0},
- {4'b0, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
- {pps_int,overrun,underrun,PHY_INTn,i2c_int,spi_int,timer_int,buffer_int}};
-
- pic pic(.clk_i(wb_clk),.rst_i(wb_rst),.cyc_i(s8_cyc),.stb_i(s8_stb),.adr_i(s8_adr[4:2]),
- .we_i(s8_we),.dat_i(s8_dat_o),.dat_o(s8_dat_i),.ack_o(s8_ack),.int_o(proc_int),
- .irq(irq) );
-
- // /////////////////////////////////////////////////////////////////////////
- // Master Timer, Slave #9
-
- wire [31:0] master_time;
- timer timer
- (.wb_clk_i(wb_clk),.rst_i(wb_rst),
- .cyc_i(s9_cyc),.stb_i(s9_stb),.adr_i(s9_adr[4:2]),
- .we_i(s9_we),.dat_i(s9_dat_o),.dat_o(s9_dat_i),.ack_o(s9_ack),
- .sys_clk_i(dsp_clk),.master_time_i(master_time),.int_o(timer_int) );
-
- // /////////////////////////////////////////////////////////////////////////
- // UART, Slave #10
-
- simple_uart #(.TXDEPTH(3),.RXDEPTH(3)) uart // depth of 3 is 128 entries
- (.clk_i(wb_clk),.rst_i(wb_rst),
- .we_i(sa_we),.stb_i(sa_stb),.cyc_i(sa_cyc),.ack_o(sa_ack),
- .adr_i(sa_adr[4:2]),.dat_i(sa_dat_o),.dat_o(sa_dat_i),
- .rx_int_o(uart_rx_int),.tx_int_o(uart_tx_int),
- .tx_o(uart_tx_o),.rx_i(uart_rx_i),.baud_o(uart_baud_o));
-
- // /////////////////////////////////////////////////////////////////////////
- // ATR Controller, Slave #11
-
- wire run_rx, run_tx;
- reg run_rx_d1;
- always @(posedge dsp_clk)
- run_rx_d1 <= run_rx;
-
- atr_controller atr_controller
- (.clk_i(wb_clk),.rst_i(wb_rst),
- .adr_i(sb_adr[5:0]),.sel_i(sb_sel),.dat_i(sb_dat_o),.dat_o(sb_dat_i),
- .we_i(sb_we),.stb_i(sb_stb),.cyc_i(sb_cyc),.ack_o(sb_ack),
- .run_rx(run_rx_d1),.run_tx(run_tx),.ctrl_lines(atr_lines) );
-
- // //////////////////////////////////////////////////////////////////////////
- // Time Sync, Slave #12
-
- reg pps_posedge, pps_negedge, pps_pos_d1, pps_neg_d1;
- always @(negedge dsp_clk) pps_negedge <= pps_in;
- always @(posedge dsp_clk) pps_posedge <= pps_in;
- always @(posedge dsp_clk) pps_pos_d1 <= pps_posedge;
- always @(posedge dsp_clk) pps_neg_d1 <= pps_negedge;
-
- wire pps_o;
- time_sync time_sync
- (.wb_clk_i(wb_clk),.rst_i(wb_rst),
- .cyc_i(sc_cyc),.stb_i(sc_stb),.adr_i(sc_adr[4:2]),
- .we_i(sc_we),.dat_i(sc_dat_o),.dat_o(sc_dat_i),.ack_o(sc_ack),
- .sys_clk_i(dsp_clk),.master_time_o(master_time),
- .pps_posedge(pps_posedge),.pps_negedge(pps_negedge),
- .exp_pps_in(exp_pps_in),.exp_pps_out(exp_pps_out),
- .int_o(pps_int),.epoch_o(epoch),.pps_o(pps_o) );
-
- // /////////////////////////////////////////////////////////////////////////
- // SD Card Reader / Writer, Slave #13
-
- sd_spi_wb sd_spi_wb
- (.clk(wb_clk),.rst(wb_rst),
- .sd_clk(sd_clk),.sd_csn(sd_csn),.sd_mosi(sd_mosi),.sd_miso(sd_miso),
- .wb_cyc_i(sd_cyc),.wb_stb_i(sd_stb),.wb_we_i(sd_we),
- .wb_adr_i(sd_adr[3:2]),.wb_dat_i(sd_dat_o[7:0]),.wb_dat_o(sd_dat_i[7:0]),
- .wb_ack_o(sd_ack) );
-
- assign sd_dat_i[31:8] = 0;
-
- // /////////////////////////////////////////////////////////////////////////
- // DSP
- wire [31:0] sample_rx, sample_tx;
- wire strobe_rx, strobe_tx;
-
- rx_control #(.FIFOSIZE(10)) rx_control
- (.clk(dsp_clk), .rst(dsp_rst),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .master_time(master_time),.overrun(overrun),
- .wr_dat_o(wr1_dat), .wr_flags_o(wr1_flags), .wr_ready_o(wr1_ready_i), .wr_ready_i(wr1_ready_o),
- .sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
- .fifo_occupied(dsp_rx_occ),.fifo_full(dsp_rx_full),.fifo_empty(dsp_rx_empty),
- .debug_rx(debug_rx) );
-
- dsp_core_rx_old dsp_core_rx_old
- (.clk(dsp_clk),.rst(dsp_rst),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .adc_a(adc_a),.adc_ovf_a(adc_ovf_a),.adc_b(adc_b),.adc_ovf_b(adc_ovf_b),
- .sample(sample_rx), .run(run_rx_d1), .strobe(strobe_rx),
- .debug(debug_rx_dsp) );
-
- tx_control #(.FIFOSIZE(10)) tx_control
- (.clk(dsp_clk), .rst(dsp_rst),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .master_time(master_time),.underrun(underrun),
- .rd_dat_i(rd1_dat), .rd_flags_i(rd1_flags), .rd_ready_i(rd1_ready_o), .rd_ready_o(rd1_ready_i),
- .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
- .fifo_occupied(dsp_tx_occ),.fifo_full(dsp_tx_full),.fifo_empty(dsp_tx_empty),
- .debug(debug_txc) );
-
- dsp_core_tx #(.BASE(SR_TX_DSP)) dsp_core_tx
- (.clk(dsp_clk),.rst(dsp_rst),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .sample(sample_tx), .run(run_tx), .strobe(strobe_tx),
- .dac_a(dac_a),.dac_b(dac_b),
- .debug(debug_tx_dsp) );
-
- assign dsp_rst = wb_rst;
-
- // ///////////////////////////////////////////////////////////////////////////////////
- // SERDES
-
- serdes #(.TXFIFOSIZE(SERDES_TX_FIFOSIZE),.RXFIFOSIZE(SERDES_RX_FIFOSIZE)) serdes
- (.clk(dsp_clk),.rst(dsp_rst),
- .ser_tx_clk(ser_tx_clk),.ser_t(ser_t),.ser_tklsb(ser_tklsb),.ser_tkmsb(ser_tkmsb),
- .rd_dat_i(rd0_dat),.rd_flags_i(rd0_flags),.rd_ready_o(rd0_ready_i),.rd_ready_i(rd0_ready_o),
- .ser_rx_clk(ser_rx_clk),.ser_r(ser_r),.ser_rklsb(ser_rklsb),.ser_rkmsb(ser_rkmsb),
- .wr_dat_o(wr0_dat),.wr_flags_o(wr0_flags),.wr_ready_o(wr0_ready_i),.wr_ready_i(wr0_ready_o),
- .tx_occupied(ser_tx_occ),.tx_full(ser_tx_full),.tx_empty(ser_tx_empty),
- .rx_occupied(ser_rx_occ),.rx_full(ser_rx_full),.rx_empty(ser_rx_empty),
- .serdes_link_up(serdes_link_up),.debug0(debug_serdes0), .debug1(debug_serdes1) );
-
- // ///////////////////////////////////////////////////////////////////////////////////
- // External RAM Interface
-/*
- localparam PAGE_SIZE = 10; // PAGE SIZE is in bytes, 10 = 1024 bytes
-
- wire [15:0] bus2ram, ram2bus;
- wire [15:0] bridge_adr;
- wire [1:0] bridge_sel;
- wire bridge_stb, bridge_cyc, bridge_we, bridge_ack;
-
- wire [19:0] page;
- wire [19:0] wb_ram_adr = {page[19:PAGE_SIZE],bridge_adr[PAGE_SIZE-1:0]};
- setting_reg #(.my_addr(6),.width(20)) sr_page (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(page),.changed());
-
- wb_bridge_16_32 bridge
- (.wb_clk(wb_clk),.wb_rst(wb_rst),
- .A_cyc_i(se_cyc),.A_stb_i(se_stb),.A_we_i(se_we),.A_sel_i(se_sel),
- .A_adr_i(se_adr),.A_dat_i(se_dat_o),.A_dat_o(se_dat_i),.A_ack_o(se_ack),
- .B_cyc_o(bridge_cyc),.B_stb_o(bridge_stb),.B_we_o(bridge_we),.B_sel_o(bridge_sel),
- .B_adr_o(bridge_adr),.B_dat_o(bus2ram),.B_dat_i(ram2bus),.B_ack_i(bridge_ack));
-
- wb_zbt16_b wb_zbt16_b
- (.clk(wb_clk),.rst(wb_rst),
- .wb_adr_i(wb_ram_adr),.wb_dat_i(bus2ram),.wb_dat_o(ram2bus),.wb_sel_i(bridge_sel),
- .wb_cyc_i(bridge_cyc),.wb_stb_i(bridge_stb),.wb_ack_o(bridge_ack),.wb_we_i(bridge_we),
- .sram_clk(RAM_CLK),.sram_a(RAM_A),.sram_d(RAM_D[15:0]),.sram_we(RAM_WEn),
- .sram_bw(),.sram_adv(RAM_LDn),.sram_ce(RAM_CENn),.sram_oe(RAM_OEn),
- .sram_mode(),.sram_zz() );
-
-*/
- assign RAM_CE1n = 0;
- assign RAM_D[17:16] = 2'bzz;
-
- // /////////////////////////////////////////////////////////////////////////////////////////
- // Debug Pins
-
- // FIFO Level Debugging
- reg [31:0] host_to_dsp_fifo,dsp_to_host_fifo,eth_mac_debug,serdes_to_dsp_fifo,dsp_to_serdes_fifo;
-
- always @(posedge dsp_clk)
- serdes_to_dsp_fifo <= { {ser_rx_full,ser_rx_empty,ser_rx_occ[13:0]},
- {dsp_tx_full,dsp_tx_empty,dsp_tx_occ[13:0]} };
-
- always @(posedge dsp_clk)
- dsp_to_serdes_fifo <= { {ser_tx_full,ser_tx_empty,ser_tx_occ[13:0]},
- {dsp_rx_full,dsp_rx_empty,dsp_rx_occ[13:0]} };
-
- always @(posedge dsp_clk)
- host_to_dsp_fifo <= { {eth_rx_full,eth_rx_empty,eth_rx_occ[13:0]},
- {dsp_tx_full,dsp_tx_empty,dsp_tx_occ[13:0]} };
-
- always @(posedge dsp_clk)
- dsp_to_host_fifo <= { {eth_tx_full,eth_tx_empty,eth_tx_occ[13:0]},
- {dsp_rx_full,dsp_rx_empty,dsp_rx_occ[13:0]} };
-
- always @(posedge dsp_clk)
- eth_mac_debug <= { { 6'd0, GMII_TX_EN, GMII_RX_DV, debug_mac0[7:0]},
- {eth_rx_full2, eth_rx_empty2, eth_rx_occ2[13:0]} };
-
- assign debug_clk[0] = 0; // wb_clk;
- assign debug_clk[1] = clk_to_mac;
-/*
-
- wire mdio_cpy = MDIO;
- assign debug = { { 1'b0, s6_stb, s6_ack, s6_we, s6_sel[3:0] },
- { s6_adr[15:8] },
- { s6_adr[7:0] },
- { 6'd0, mdio_cpy, MDC } };
-*/
-/*
- assign debug = { { GMII_TXD },
- { 5'd0, GMII_TX_EN, GMII_TX_ER, GMII_GTX_CLK },
- { wr2_flags, rd2_flags },
- { 4'd0, wr2_ready_i, wr2_ready_o, rd2_ready_i, rd2_ready_o } };
- */
- assign debug = { { GMII_RXD },
- { 5'd0, GMII_RX_DV, GMII_RX_ER, GMII_RX_CLK },
- { wr2_flags, rd2_flags },
- { GMII_TX_EN,3'd0, wr2_ready_i, wr2_ready_o, rd2_ready_i, rd2_ready_o } };
-
- assign debug_gpio_0 = 0;
- //debug_mac; //eth_mac_debug;
- assign debug_gpio_1 = 0;
-
-endmodule // u2_core
-
-// wire debug_mux;
-// setting_reg #(.my_addr(5)) sr_debug (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
-// .in(set_data),.out(debug_mux),.changed());
-
-//assign debug = debug_mux ? host_to_dsp_fifo : dsp_to_host_fifo;
-//assign debug = debug_mux ? serdes_to_dsp_fifo : dsp_to_serdes_fifo;
-
-//assign debug = {{strobe_rx,/*adc_ovf_a*/ 1'b0,adc_a},
-// {run_rx,/*adc_ovf_b*/ 1'b0,adc_b}};
-
-//assign debug = debug_tx_dsp;
-//assign debug = debug_serdes0;
-
-//assign debug_gpio_0 = 0; //debug_serdes0;
-//assign debug_gpio_1 = 0; //debug_serdes1;
-
-// assign debug={{3'b0, wb_clk, wb_rst, dsp_rst, por, config_success},
-// {8'b0},
-// {3'b0,ram_loader_ack, ram_loader_stb, ram_loader_we,ram_loader_rst,ram_loader_done },
-// {cpld_start,cpld_mode,cpld_done,cpld_din,cpld_clk,cpld_detached,cpld_misc,cpld_init_b} };
-
-//assign debug = {dac_a,dac_b};
-
-/*
- assign debug = {{ram_loader_done, takeover, 6'd0},
- {1'b0, cpld_start_int, cpld_mode_int, cpld_done_int, sd_clk, sd_csn, sd_miso, sd_mosi},
- {8'd0},
- {cpld_start, cpld_mode, cpld_done, cpld_din, cpld_misc, cpld_detached, cpld_clk, cpld_init_b}}; */
-
-/*assign debug = host_to_dsp_fifo;
- assign debug_gpio_0 = eth_mac_debug;
- assign debug_gpio_1 = 0;
- */
-// Assign various commonly used debug buses.
-/*
- wire [31:0] debug_rx_1 = {uart_tx_o,GMII_TX_EN,strobe_rx,overrun,proc_int,buffer_int,timer_int,GMII_RX_DV,
- irq[7:0],
- GMII_RXD,
- GMII_TXD};
-
- wire [31:0] debug_rx_2 = { 5'd0, s8_we, s8_stb, s8_ack, debug_rx[23:0] };
-
- wire [31:0] debug_time = {uart_tx_o, 7'b0,
- irq[7:0],
- 6'b0, GMII_RX_DV, GMII_TX_EN,
- 4'b0, exp_pps_in, exp_pps_out, pps_in, pps_int};
-
- wire [31:0] debug_irq = {uart_tx_o, iwb_adr, iwb_ack,
- irq[7:0],
- proc_int, 7'b0 };
-
- wire [31:0] debug_eth =
- {{uart_tx_o,proc_int,underrun,buffer_int,wr2_ready,wr2_error,wr2_done,wr2_write},
- {8'd0},
- {8'd0},
- {GMII_TX_EN,GMII_RX_DV,Rx_mac_empty,Rx_mac_rd,Rx_mac_err,Rx_mac_sop,Rx_mac_eop,wr2_full} };
-
- assign debug_serdes0 = { { rd0_dat[7:0] },
- { ser_tx_clk, ser_tkmsb, ser_tklsb, rd0_sop, rd0_eop, rd0_read, rd0_error, rd0_done },
- { ser_t[15:8] },
- { ser_t[7:0] } };
-
- assign debug_serdes1 = { {1'b0,proc_int,underrun,buffer_int,wr0_ready,wr0_error,wr0_done,wr0_write},
- { 1'b0, ser_rx_clk, ser_rkmsb, ser_rklsb, ser_enable, ser_prbsen, ser_loopen, ser_rx_en },
- { ser_r[15:8] },
- { ser_r[7:0] } };
-
- assign debug_gpio_1 = {uart_tx_o,7'd0,
- 3'd0,rd1_sop,rd1_eop,rd1_read,rd1_done,rd1_error,
- debug_txc[15:0]};
- assign debug_gpio_1 = debug_rx;
- assign debug_gpio_1 = debug_serdes1;
- assign debug_gpio_1 = debug_eth;
-
- */
-
--
cgit v1.2.3
From 66e1d8f94b82df3dccbe6f785c7224f0763009f3 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Thu, 9 Dec 2010 23:39:49 -0800
Subject: udp is now the default
---
usrp2/top/u2_rev3/Makefile.udp | 4 +-
usrp2/top/u2_rev3/u2_core.v | 735 ++++++++++++++++++++++++++++++++++++++++
usrp2/top/u2_rev3/u2_core_udp.v | 735 ----------------------------------------
3 files changed, 737 insertions(+), 737 deletions(-)
create mode 100644 usrp2/top/u2_rev3/u2_core.v
delete mode 100644 usrp2/top/u2_rev3/u2_core_udp.v
(limited to 'usrp2')
diff --git a/usrp2/top/u2_rev3/Makefile.udp b/usrp2/top/u2_rev3/Makefile.udp
index 99effb038..05ada2476 100644
--- a/usrp2/top/u2_rev3/Makefile.udp
+++ b/usrp2/top/u2_rev3/Makefile.udp
@@ -6,7 +6,7 @@
# Project Setup
##################################################
TOP_MODULE = u2_rev3
-BUILD_DIR = $(abspath build-udp$(ISE))
+BUILD_DIR = $(abspath build)
##################################################
# Include other makefiles
@@ -46,7 +46,7 @@ simulator "ISE Simulator (VHDL/Verilog)" \
# Sources
##################################################
TOP_SRCS = \
-u2_core_udp.v \
+u2_core.v \
u2_rev3.v \
u2_rev3.ucf
diff --git a/usrp2/top/u2_rev3/u2_core.v b/usrp2/top/u2_rev3/u2_core.v
new file mode 100644
index 000000000..c2d473650
--- /dev/null
+++ b/usrp2/top/u2_rev3/u2_core.v
@@ -0,0 +1,735 @@
+// ////////////////////////////////////////////////////////////////////////////////
+// Module Name: u2_core
+// ////////////////////////////////////////////////////////////////////////////////
+
+module u2_core
+ #(parameter RAM_SIZE=32768)
+ (// Clocks
+ input dsp_clk,
+ input wb_clk,
+ output clock_ready,
+ input clk_to_mac,
+ input pps_in,
+
+ // Misc, debug
+ output [7:0] leds,
+ output [31:0] debug,
+ output [1:0] debug_clk,
+
+ // Expansion
+ input exp_time_in,
+ output exp_time_out,
+
+ // GMII
+ // GMII-CTRL
+ input GMII_COL,
+ input GMII_CRS,
+
+ // GMII-TX
+ output [7:0] GMII_TXD,
+ output GMII_TX_EN,
+ output GMII_TX_ER,
+ output GMII_GTX_CLK,
+ input GMII_TX_CLK, // 100mbps clk
+
+ // GMII-RX
+ input [7:0] GMII_RXD,
+ input GMII_RX_CLK,
+ input GMII_RX_DV,
+ input GMII_RX_ER,
+
+ // GMII-Management
+ inout MDIO,
+ output MDC,
+ input PHY_INTn, // open drain
+ output PHY_RESETn,
+
+ // SERDES
+ output ser_enable,
+ output ser_prbsen,
+ output ser_loopen,
+ output ser_rx_en,
+
+ output ser_tx_clk,
+ output [15:0] ser_t,
+ output ser_tklsb,
+ output ser_tkmsb,
+
+ input ser_rx_clk,
+ input [15:0] ser_r,
+ input ser_rklsb,
+ input ser_rkmsb,
+
+ // CPLD interface
+ output cpld_start,
+ output cpld_mode,
+ output cpld_done,
+ input cpld_din,
+ input cpld_clk,
+ input cpld_detached,
+ output cpld_misc,
+ input cpld_init_b,
+ input por,
+ output config_success,
+
+ // ADC
+ input [13:0] adc_a,
+ input adc_ovf_a,
+ output adc_on_a,
+ output adc_oe_a,
+
+ input [13:0] adc_b,
+ input adc_ovf_b,
+ output adc_on_b,
+ output adc_oe_b,
+
+ // DAC
+ output [15:0] dac_a,
+ output [15:0] dac_b,
+
+ // I2C
+ input scl_pad_i,
+ output scl_pad_o,
+ output scl_pad_oen_o,
+ input sda_pad_i,
+ output sda_pad_o,
+ output sda_pad_oen_o,
+
+ // Clock Gen Control
+ output [1:0] clk_en,
+ output [1:0] clk_sel,
+ input clk_func, // FIXME is an input to control the 9510
+ input clk_status,
+
+ // Generic SPI
+ output sclk,
+ output mosi,
+ input miso,
+ output sen_clk,
+ output sen_dac,
+ output sen_tx_db,
+ output sen_tx_adc,
+ output sen_tx_dac,
+ output sen_rx_db,
+ output sen_rx_adc,
+ output sen_rx_dac,
+
+ // GPIO to DBoards
+ inout [15:0] io_tx,
+ inout [15:0] io_rx,
+
+ // External RAM
+ input [17:0] RAM_D_pi,
+ output [17:0] RAM_D_po,
+ output RAM_D_poe,
+ output [18:0] RAM_A,
+ output RAM_CE1n,
+ output RAM_CENn,
+ output RAM_WEn,
+ output RAM_OEn,
+ output RAM_LDn,
+
+ // Debug stuff
+ output uart_tx_o,
+ input uart_rx_i,
+ output uart_baud_o,
+ input sim_mode,
+ input [3:0] clock_divider
+ );
+
+ localparam SR_BUF_POOL = 64; // Uses 1 reg
+ localparam SR_UDP_SM = 96; // 64 regs
+ localparam SR_RX_DSP = 160; // 16
+ localparam SR_RX_CTRL = 176; // 16
+ localparam SR_TIME64 = 192; // 3
+ localparam SR_SIMTIMER = 198; // 2
+ localparam SR_TX_DSP = 208; // 16
+ localparam SR_TX_CTRL = 224; // 16
+
+ // FIFO Sizes, 9 = 512 lines, 10 = 1024, 11 = 2048
+ // all (most?) are 36 bits wide, so 9 is 1 BRAM, 10 is 2, 11 is 4 BRAMs
+ localparam DSP_TX_FIFOSIZE = 10;
+ localparam DSP_RX_FIFOSIZE = 10;
+ localparam ETH_TX_FIFOSIZE = 10;
+ localparam ETH_RX_FIFOSIZE = 11;
+ localparam SERDES_TX_FIFOSIZE = 9;
+ localparam SERDES_RX_FIFOSIZE = 9; // RX currently doesn't use a fifo?
+
+ wire [7:0] set_addr, set_addr_dsp;
+ wire [31:0] set_data, set_data_dsp;
+ wire set_stb, set_stb_dsp;
+
+ wire ram_loader_done;
+ wire ram_loader_rst, wb_rst, dsp_rst;
+ assign dsp_rst = wb_rst;
+
+ wire [31:0] status, status_b0, status_b1, status_b2, status_b3, status_b4, status_b5, status_b6, status_b7;
+ wire bus_error, spi_int, i2c_int, pps_int, onetime_int, periodic_int, buffer_int;
+ wire proc_int, overrun, underrun, uart_tx_int, uart_rx_int;
+
+ wire [31:0] debug_gpio_0, debug_gpio_1;
+ wire [31:0] atr_lines;
+
+ wire [31:0] debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc,
+ debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp, debug_udp, debug_extfifo, debug_extfifo2;
+
+ wire [15:0] ser_rx_occ, ser_tx_occ, dsp_rx_occ, dsp_tx_occ, eth_rx_occ, eth_tx_occ, eth_rx_occ2;
+ wire ser_rx_full, ser_tx_full, dsp_rx_full, dsp_tx_full, eth_rx_full, eth_tx_full, eth_rx_full2;
+ wire ser_rx_empty, ser_tx_empty, dsp_rx_empty, dsp_tx_empty, eth_rx_empty, eth_tx_empty, eth_rx_empty2;
+
+ wire serdes_link_up;
+ wire epoch;
+ wire [31:0] irq;
+ wire [63:0] vita_time;
+
+ wire run_rx, run_tx;
+ reg run_rx_d1;
+ always @(posedge dsp_clk)
+ run_rx_d1 <= run_rx;
+
+ // ///////////////////////////////////////////////////////////////////////////////////////////////
+ // Wishbone Single Master INTERCON
+ localparam dw = 32; // Data bus width
+ localparam aw = 16; // Address bus width, for byte addressibility, 16 = 64K byte memory space
+ localparam sw = 4; // Select width -- 32-bit data bus with 8-bit granularity.
+
+ wire [dw-1:0] m0_dat_o, m0_dat_i;
+ wire [dw-1:0] s0_dat_o, s1_dat_o, s0_dat_i, s1_dat_i, s2_dat_o, s3_dat_o, s2_dat_i, s3_dat_i,
+ s4_dat_o, s5_dat_o, s4_dat_i, s5_dat_i, s6_dat_o, s7_dat_o, s6_dat_i, s7_dat_i,
+ s8_dat_o, s9_dat_o, s8_dat_i, s9_dat_i, sa_dat_o, sa_dat_i, sb_dat_i, sb_dat_o,
+ sc_dat_i, sc_dat_o, sd_dat_i, sd_dat_o, se_dat_i, se_dat_o;
+ wire [aw-1:0] m0_adr,s0_adr,s1_adr,s2_adr,s3_adr,s4_adr,s5_adr,s6_adr,s7_adr,s8_adr,s9_adr,sa_adr,sb_adr,sc_adr, sd_adr, se_adr;
+ wire [sw-1:0] m0_sel,s0_sel,s1_sel,s2_sel,s3_sel,s4_sel,s5_sel,s6_sel,s7_sel,s8_sel,s9_sel,sa_sel,sb_sel,sc_sel, sd_sel, se_sel;
+ wire m0_ack,s0_ack,s1_ack,s2_ack,s3_ack,s4_ack,s5_ack,s6_ack,s7_ack,s8_ack,s9_ack,sa_ack,sb_ack,sc_ack, sd_ack, se_ack;
+ wire m0_stb,s0_stb,s1_stb,s2_stb,s3_stb,s4_stb,s5_stb,s6_stb,s7_stb,s8_stb,s9_stb,sa_stb,sb_stb,sc_stb, sd_stb, se_stb;
+ wire m0_cyc,s0_cyc,s1_cyc,s2_cyc,s3_cyc,s4_cyc,s5_cyc,s6_cyc,s7_cyc,s8_cyc,s9_cyc,sa_cyc,sb_cyc,sc_cyc, sd_cyc, se_cyc;
+ wire m0_err, m0_rty;
+ wire m0_we,s0_we,s1_we,s2_we,s3_we,s4_we,s5_we,s6_we,s7_we,s8_we,s9_we,sa_we,sb_we,sc_we,sd_we, se_we;
+
+ wb_1master #(.decode_w(6),
+ .s0_addr(6'b0000_00),.s0_mask(6'b100000),
+ .s1_addr(6'b1000_00),.s1_mask(6'b110000),
+ .s2_addr(6'b1100_00),.s2_mask(6'b111111),
+ .s3_addr(6'b1100_01),.s3_mask(6'b111111),
+ .s4_addr(6'b1100_10),.s4_mask(6'b111111),
+ .s5_addr(6'b1100_11),.s5_mask(6'b111111),
+ .s6_addr(6'b1101_00),.s6_mask(6'b111111),
+ .s7_addr(6'b1101_01),.s7_mask(6'b111111),
+ .s8_addr(6'b1101_10),.s8_mask(6'b111111),
+ .s9_addr(6'b1101_11),.s9_mask(6'b111111),
+ .sa_addr(6'b1110_00),.sa_mask(6'b111111),
+ .sb_addr(6'b1110_01),.sb_mask(6'b111111),
+ .sc_addr(6'b1110_10),.sc_mask(6'b111111),
+ .sd_addr(6'b1110_11),.sd_mask(6'b111111),
+ .se_addr(6'b1111_00),.se_mask(6'b111111),
+ .sf_addr(6'b1111_01),.sf_mask(6'b111111),
+ .dw(dw),.aw(aw),.sw(sw)) wb_1master
+ (.clk_i(wb_clk),.rst_i(wb_rst),
+ .m0_dat_o(m0_dat_o),.m0_ack_o(m0_ack),.m0_err_o(m0_err),.m0_rty_o(m0_rty),.m0_dat_i(m0_dat_i),
+ .m0_adr_i(m0_adr),.m0_sel_i(m0_sel),.m0_we_i(m0_we),.m0_cyc_i(m0_cyc),.m0_stb_i(m0_stb),
+ .s0_dat_o(s0_dat_o),.s0_adr_o(s0_adr),.s0_sel_o(s0_sel),.s0_we_o (s0_we),.s0_cyc_o(s0_cyc),.s0_stb_o(s0_stb),
+ .s0_dat_i(s0_dat_i),.s0_ack_i(s0_ack),.s0_err_i(0),.s0_rty_i(0),
+ .s1_dat_o(s1_dat_o),.s1_adr_o(s1_adr),.s1_sel_o(s1_sel),.s1_we_o (s1_we),.s1_cyc_o(s1_cyc),.s1_stb_o(s1_stb),
+ .s1_dat_i(s1_dat_i),.s1_ack_i(s1_ack),.s1_err_i(0),.s1_rty_i(0),
+ .s2_dat_o(s2_dat_o),.s2_adr_o(s2_adr),.s2_sel_o(s2_sel),.s2_we_o (s2_we),.s2_cyc_o(s2_cyc),.s2_stb_o(s2_stb),
+ .s2_dat_i(s2_dat_i),.s2_ack_i(s2_ack),.s2_err_i(0),.s2_rty_i(0),
+ .s3_dat_o(s3_dat_o),.s3_adr_o(s3_adr),.s3_sel_o(s3_sel),.s3_we_o (s3_we),.s3_cyc_o(s3_cyc),.s3_stb_o(s3_stb),
+ .s3_dat_i(s3_dat_i),.s3_ack_i(s3_ack),.s3_err_i(0),.s3_rty_i(0),
+ .s4_dat_o(s4_dat_o),.s4_adr_o(s4_adr),.s4_sel_o(s4_sel),.s4_we_o (s4_we),.s4_cyc_o(s4_cyc),.s4_stb_o(s4_stb),
+ .s4_dat_i(s4_dat_i),.s4_ack_i(s4_ack),.s4_err_i(0),.s4_rty_i(0),
+ .s5_dat_o(s5_dat_o),.s5_adr_o(s5_adr),.s5_sel_o(s5_sel),.s5_we_o (s5_we),.s5_cyc_o(s5_cyc),.s5_stb_o(s5_stb),
+ .s5_dat_i(s5_dat_i),.s5_ack_i(s5_ack),.s5_err_i(0),.s5_rty_i(0),
+ .s6_dat_o(s6_dat_o),.s6_adr_o(s6_adr),.s6_sel_o(s6_sel),.s6_we_o (s6_we),.s6_cyc_o(s6_cyc),.s6_stb_o(s6_stb),
+ .s6_dat_i(s6_dat_i),.s6_ack_i(s6_ack),.s6_err_i(0),.s6_rty_i(0),
+ .s7_dat_o(s7_dat_o),.s7_adr_o(s7_adr),.s7_sel_o(s7_sel),.s7_we_o (s7_we),.s7_cyc_o(s7_cyc),.s7_stb_o(s7_stb),
+ .s7_dat_i(s7_dat_i),.s7_ack_i(s7_ack),.s7_err_i(0),.s7_rty_i(0),
+ .s8_dat_o(s8_dat_o),.s8_adr_o(s8_adr),.s8_sel_o(s8_sel),.s8_we_o (s8_we),.s8_cyc_o(s8_cyc),.s8_stb_o(s8_stb),
+ .s8_dat_i(s8_dat_i),.s8_ack_i(s8_ack),.s8_err_i(0),.s8_rty_i(0),
+ .s9_dat_o(s9_dat_o),.s9_adr_o(s9_adr),.s9_sel_o(s9_sel),.s9_we_o (s9_we),.s9_cyc_o(s9_cyc),.s9_stb_o(s9_stb),
+ .s9_dat_i(s9_dat_i),.s9_ack_i(s9_ack),.s9_err_i(0),.s9_rty_i(0),
+ .sa_dat_o(sa_dat_o),.sa_adr_o(sa_adr),.sa_sel_o(sa_sel),.sa_we_o(sa_we),.sa_cyc_o(sa_cyc),.sa_stb_o(sa_stb),
+ .sa_dat_i(sa_dat_i),.sa_ack_i(sa_ack),.sa_err_i(0),.sa_rty_i(0),
+ .sb_dat_o(sb_dat_o),.sb_adr_o(sb_adr),.sb_sel_o(sb_sel),.sb_we_o(sb_we),.sb_cyc_o(sb_cyc),.sb_stb_o(sb_stb),
+ .sb_dat_i(sb_dat_i),.sb_ack_i(sb_ack),.sb_err_i(0),.sb_rty_i(0),
+ .sc_dat_o(sc_dat_o),.sc_adr_o(sc_adr),.sc_sel_o(sc_sel),.sc_we_o(sc_we),.sc_cyc_o(sc_cyc),.sc_stb_o(sc_stb),
+ .sc_dat_i(sc_dat_i),.sc_ack_i(sc_ack),.sc_err_i(0),.sc_rty_i(0),
+ .sd_dat_o(sd_dat_o),.sd_adr_o(sd_adr),.sd_sel_o(sd_sel),.sd_we_o(sd_we),.sd_cyc_o(sd_cyc),.sd_stb_o(sd_stb),
+ .sd_dat_i(sd_dat_i),.sd_ack_i(sd_ack),.sd_err_i(0),.sd_rty_i(0),
+ .se_dat_o(se_dat_o),.se_adr_o(se_adr),.se_sel_o(se_sel),.se_we_o(se_we),.se_cyc_o(se_cyc),.se_stb_o(se_stb),
+ .se_dat_i(se_dat_i),.se_ack_i(se_ack),.se_err_i(0),.se_rty_i(0),
+ .sf_dat_i(0),.sf_ack_i(0),.sf_err_i(0),.sf_rty_i(0) );
+
+ //////////////////////////////////////////////////////////////////////////////////////////
+ // Reset Controller
+ system_control sysctrl (.wb_clk_i(wb_clk), // .por_i(por),
+ .ram_loader_rst_o(ram_loader_rst),
+ .wb_rst_o(wb_rst),
+ .ram_loader_done_i(ram_loader_done));
+
+ assign config_success = ram_loader_done;
+ reg takeover = 0;
+
+ wire cpld_start_int, cpld_mode_int, cpld_done_int;
+
+ always @(posedge wb_clk)
+ if(ram_loader_done)
+ takeover = 1;
+ assign cpld_misc = ~takeover;
+
+ wire sd_clk, sd_csn, sd_mosi, sd_miso;
+
+ assign sd_miso = cpld_din;
+ assign cpld_start = takeover ? sd_clk : cpld_start_int;
+ assign cpld_mode = takeover ? sd_csn : cpld_mode_int;
+ assign cpld_done = takeover ? sd_mosi : cpld_done_int;
+
+ // ///////////////////////////////////////////////////////////////////
+ // RAM Loader
+
+ wire [31:0] ram_loader_dat, if_dat;
+ wire [15:0] ram_loader_adr;
+ wire [14:0] if_adr;
+ wire [3:0] ram_loader_sel;
+ wire ram_loader_stb, ram_loader_we;
+ wire iwb_ack, iwb_stb;
+ ram_loader #(.AWIDTH(16),.RAM_SIZE(RAM_SIZE))
+ ram_loader (.wb_clk(wb_clk),.dsp_clk(dsp_clk),.ram_loader_rst(ram_loader_rst),
+ .wb_dat(ram_loader_dat),.wb_adr(ram_loader_adr),
+ .wb_stb(ram_loader_stb),.wb_sel(ram_loader_sel),
+ .wb_we(ram_loader_we),
+ .ram_loader_done(ram_loader_done),
+ // CPLD Interface
+ .cpld_clk(cpld_clk),
+ .cpld_din(cpld_din),
+ .cpld_start(cpld_start_int),
+ .cpld_mode(cpld_mode_int),
+ .cpld_done(cpld_done_int),
+ .cpld_detached(cpld_detached));
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Processor
+ aeMB_core_BE #(.ISIZ(16),.DSIZ(16),.MUL(0),.BSF(1))
+ aeMB (.sys_clk_i(wb_clk), .sys_rst_i(wb_rst),
+ // Instruction Wishbone bus to I-RAM
+ .if_adr(if_adr),
+ .if_dat(if_dat),
+ // Data Wishbone bus to system bus fabric
+ .dwb_we_o(m0_we),.dwb_stb_o(m0_stb),.dwb_dat_o(m0_dat_i),.dwb_adr_o(m0_adr),
+ .dwb_dat_i(m0_dat_o),.dwb_ack_i(m0_ack),.dwb_sel_o(m0_sel),.dwb_cyc_o(m0_cyc),
+ // Interrupts and exceptions
+ .sys_int_i(proc_int),.sys_exc_i(bus_error) );
+
+ assign bus_error = m0_err | m0_rty;
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Dual Ported RAM -- D-Port is Slave #0 on main Wishbone
+ // I-port connects directly to processor and ram loader
+
+ wire flush_icache;
+ ram_harvard #(.AWIDTH(15),.RAM_SIZE(RAM_SIZE),.ICWIDTH(7),.DCWIDTH(6))
+ sys_ram(.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
+
+ .ram_loader_adr_i(ram_loader_adr[14:0]), .ram_loader_dat_i(ram_loader_dat),
+ .ram_loader_stb_i(ram_loader_stb), .ram_loader_sel_i(ram_loader_sel),
+ .ram_loader_we_i(ram_loader_we),
+ .ram_loader_done_i(ram_loader_done),
+
+ .if_adr(if_adr),
+ .if_data(if_dat),
+
+ .dwb_adr_i(s0_adr[14:0]), .dwb_dat_i(s0_dat_o), .dwb_dat_o(s0_dat_i),
+ .dwb_we_i(s0_we), .dwb_ack_o(s0_ack), .dwb_stb_i(s0_stb), .dwb_sel_i(s0_sel),
+ .flush_icache(flush_icache));
+
+ setting_reg #(.my_addr(7)) sr_icache (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out(),.changed(flush_icache));
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Buffer Pool, slave #1
+ wire rd0_ready_i, rd0_ready_o;
+ wire rd1_ready_i, rd1_ready_o;
+ wire rd2_ready_i, rd2_ready_o;
+ wire rd3_ready_i, rd3_ready_o;
+ wire [3:0] rd0_flags, rd1_flags, rd2_flags, rd3_flags;
+ wire [31:0] rd0_dat, rd1_dat, rd2_dat, rd3_dat;
+
+ wire wr0_ready_i, wr0_ready_o;
+ wire wr1_ready_i, wr1_ready_o;
+ wire wr2_ready_i, wr2_ready_o;
+ wire wr3_ready_i, wr3_ready_o;
+ wire [3:0] wr0_flags, wr1_flags, wr2_flags, wr3_flags;
+ wire [31:0] wr0_dat, wr1_dat, wr2_dat, wr3_dat;
+
+ buffer_pool #(.BUF_SIZE(9), .SET_ADDR(SR_BUF_POOL)) buffer_pool
+ (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
+ .wb_we_i(s1_we),.wb_stb_i(s1_stb),.wb_adr_i(s1_adr),.wb_dat_i(s1_dat_o),
+ .wb_dat_o(s1_dat_i),.wb_ack_o(s1_ack),.wb_err_o(),.wb_rty_o(),
+
+ .stream_clk(dsp_clk), .stream_rst(dsp_rst),
+ .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
+ .status(status),.sys_int_o(buffer_int),
+
+ .s0(status_b0),.s1(status_b1),.s2(status_b2),.s3(status_b3),
+ .s4(status_b4),.s5(status_b5),.s6(status_b6),.s7(status_b7),
+
+ // Write Interfaces
+ .wr0_data_i(wr0_dat), .wr0_flags_i(wr0_flags), .wr0_ready_i(wr0_ready_i), .wr0_ready_o(wr0_ready_o),
+ .wr1_data_i(wr1_dat), .wr1_flags_i(wr1_flags), .wr1_ready_i(wr1_ready_i), .wr1_ready_o(wr1_ready_o),
+ .wr2_data_i(wr2_dat), .wr2_flags_i(wr2_flags), .wr2_ready_i(wr2_ready_i), .wr2_ready_o(wr2_ready_o),
+ .wr3_data_i(wr3_dat), .wr3_flags_i(wr3_flags), .wr3_ready_i(wr3_ready_i), .wr3_ready_o(wr3_ready_o),
+ // Read Interfaces
+ .rd0_data_o(rd0_dat), .rd0_flags_o(rd0_flags), .rd0_ready_i(rd0_ready_i), .rd0_ready_o(rd0_ready_o),
+ .rd1_data_o(rd1_dat), .rd1_flags_o(rd1_flags), .rd1_ready_i(rd1_ready_i), .rd1_ready_o(rd1_ready_o),
+ .rd2_data_o(rd2_dat), .rd2_flags_o(rd2_flags), .rd2_ready_i(rd2_ready_i), .rd2_ready_o(rd2_ready_o),
+ .rd3_data_o(rd3_dat), .rd3_flags_o(rd3_flags), .rd3_ready_i(rd3_ready_i), .rd3_ready_o(rd3_ready_o)
+ );
+
+ wire [31:0] status_enc;
+ priority_enc priority_enc (.in({16'b0,status[15:0]}), .out(status_enc));
+
+ // /////////////////////////////////////////////////////////////////////////
+ // SPI -- Slave #2
+ spi_top shared_spi
+ (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.wb_adr_i(s2_adr[4:0]),.wb_dat_i(s2_dat_o),
+ .wb_dat_o(s2_dat_i),.wb_sel_i(s2_sel),.wb_we_i(s2_we),.wb_stb_i(s2_stb),
+ .wb_cyc_i(s2_cyc),.wb_ack_o(s2_ack),.wb_err_o(),.wb_int_o(spi_int),
+ .ss_pad_o({sen_tx_db,sen_tx_adc,sen_tx_dac,sen_rx_db,sen_rx_adc,sen_rx_dac,sen_dac,sen_clk}),
+ .sclk_pad_o(sclk),.mosi_pad_o(mosi),.miso_pad_i(miso) );
+
+ // /////////////////////////////////////////////////////////////////////////
+ // I2C -- Slave #3
+ i2c_master_top #(.ARST_LVL(1))
+ i2c (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.arst_i(1'b0),
+ .wb_adr_i(s3_adr[4:2]),.wb_dat_i(s3_dat_o[7:0]),.wb_dat_o(s3_dat_i[7:0]),
+ .wb_we_i(s3_we),.wb_stb_i(s3_stb),.wb_cyc_i(s3_cyc),
+ .wb_ack_o(s3_ack),.wb_inta_o(i2c_int),
+ .scl_pad_i(scl_pad_i),.scl_pad_o(scl_pad_o),.scl_padoen_o(scl_pad_oen_o),
+ .sda_pad_i(sda_pad_i),.sda_pad_o(sda_pad_o),.sda_padoen_o(sda_pad_oen_o) );
+
+ assign s3_dat_i[31:8] = 24'd0;
+
+ // /////////////////////////////////////////////////////////////////////////
+ // GPIOs -- Slave #4
+ nsgpio nsgpio(.clk_i(wb_clk),.rst_i(wb_rst),
+ .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we),
+ .dat_i(s4_dat_o),.dat_o(s4_dat_i),.ack_o(s4_ack),
+ .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1),
+ .gpio({io_tx,io_rx}) );
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Buffer Pool Status -- Slave #5
+
+ reg [31:0] cycle_count;
+ always @(posedge wb_clk)
+ if(wb_rst)
+ cycle_count <= 0;
+ else
+ cycle_count <= cycle_count + 1;
+
+ //compatibility number -> increment when the fpga has been sufficiently altered
+ localparam compat_num = 32'd3;
+
+ wb_readback_mux buff_pool_status
+ (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
+ .wb_adr_i(s5_adr), .wb_dat_o(s5_dat_i), .wb_ack_o(s5_ack),
+
+ .word00(status_b0),.word01(status_b1),.word02(status_b2),.word03(status_b3),
+ .word04(status_b4),.word05(status_b5),.word06(status_b6),.word07(status_b7),
+ .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(vita_time[63:32]),
+ .word11(vita_time[31:0]),.word12(compat_num),.word13(irq),.word14(status_enc),.word15(cycle_count)
+ );
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Ethernet MAC Slave #6
+
+ wire [18:0] rx_f19_data, tx_f19_data;
+ wire rx_f19_src_rdy, rx_f19_dst_rdy, rx_f36_src_rdy, rx_f36_dst_rdy;
+
+ simple_gemac_wrapper19 #(.RXFIFOSIZE(11), .TXFIFOSIZE(6)) simple_gemac_wrapper19
+ (.clk125(clk_to_mac), .reset(wb_rst),
+ .GMII_GTX_CLK(GMII_GTX_CLK), .GMII_TX_EN(GMII_TX_EN),
+ .GMII_TX_ER(GMII_TX_ER), .GMII_TXD(GMII_TXD),
+ .GMII_RX_CLK(GMII_RX_CLK), .GMII_RX_DV(GMII_RX_DV),
+ .GMII_RX_ER(GMII_RX_ER), .GMII_RXD(GMII_RXD),
+ .sys_clk(dsp_clk),
+ .rx_f19_data(rx_f19_data), .rx_f19_src_rdy(rx_f19_src_rdy), .rx_f19_dst_rdy(rx_f19_dst_rdy),
+ .tx_f19_data(tx_f19_data), .tx_f19_src_rdy(tx_f19_src_rdy), .tx_f19_dst_rdy(tx_f19_dst_rdy),
+ .wb_clk(wb_clk), .wb_rst(wb_rst), .wb_stb(s6_stb), .wb_cyc(s6_cyc), .wb_ack(s6_ack),
+ .wb_we(s6_we), .wb_adr(s6_adr), .wb_dat_i(s6_dat_o), .wb_dat_o(s6_dat_i),
+ .mdio(MDIO), .mdc(MDC),
+ .debug(debug_mac));
+
+ wire [35:0] udp_tx_data, udp_rx_data;
+ wire udp_tx_src_rdy, udp_tx_dst_rdy, udp_rx_src_rdy, udp_rx_dst_rdy;
+
+ udp_wrapper #(.BASE(SR_UDP_SM)) udp_wrapper
+ (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
+ .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
+ .rx_f19_data(rx_f19_data), .rx_f19_src_rdy_i(rx_f19_src_rdy), .rx_f19_dst_rdy_o(rx_f19_dst_rdy),
+ .tx_f19_data(tx_f19_data), .tx_f19_src_rdy_o(tx_f19_src_rdy), .tx_f19_dst_rdy_i(tx_f19_dst_rdy),
+ .rx_f36_data(udp_rx_data), .rx_f36_src_rdy_o(udp_rx_src_rdy), .rx_f36_dst_rdy_i(udp_rx_dst_rdy),
+ .tx_f36_data(udp_tx_data), .tx_f36_src_rdy_i(udp_tx_src_rdy), .tx_f36_dst_rdy_o(udp_tx_dst_rdy),
+ .debug(debug_udp) );
+
+ wire [35:0] tx_err_data, udp1_tx_data;
+ wire tx_err_src_rdy, tx_err_dst_rdy, udp1_tx_src_rdy, udp1_tx_dst_rdy;
+
+ fifo_cascade #(.WIDTH(36), .SIZE(ETH_TX_FIFOSIZE)) tx_eth_fifo
+ (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
+ .datain({rd2_flags,rd2_dat}), .src_rdy_i(rd2_ready_o), .dst_rdy_o(rd2_ready_i),
+ .dataout(udp1_tx_data), .src_rdy_o(udp1_tx_src_rdy), .dst_rdy_i(udp1_tx_dst_rdy));
+
+ fifo36_mux #(.prio(0)) mux_err_stream
+ (.clk(dsp_clk), .reset(dsp_reset), .clear(0),
+ .data0_i(udp1_tx_data), .src0_rdy_i(udp1_tx_src_rdy), .dst0_rdy_o(udp1_tx_dst_rdy),
+ .data1_i(tx_err_data), .src1_rdy_i(tx_err_src_rdy), .dst1_rdy_o(tx_err_dst_rdy),
+ .data_o(udp_tx_data), .src_rdy_o(udp_tx_src_rdy), .dst_rdy_i(udp_tx_dst_rdy));
+
+ fifo_cascade #(.WIDTH(36), .SIZE(ETH_RX_FIFOSIZE)) rx_eth_fifo
+ (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
+ .datain(udp_rx_data), .src_rdy_i(udp_rx_src_rdy), .dst_rdy_o(udp_rx_dst_rdy),
+ .dataout({wr2_flags,wr2_dat}), .src_rdy_o(wr2_ready_i), .dst_rdy_i(wr2_ready_o));
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Settings Bus -- Slave #7
+ settings_bus settings_bus
+ (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s7_adr),.wb_dat_i(s7_dat_o),
+ .wb_stb_i(s7_stb),.wb_we_i(s7_we),.wb_ack_o(s7_ack),
+ .strobe(set_stb),.addr(set_addr),.data(set_data));
+
+ assign s7_dat_i = 32'd0;
+
+ settings_bus_crossclock settings_bus_crossclock
+ (.clk_i(wb_clk), .rst_i(wb_rst), .set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
+ .clk_o(dsp_clk), .rst_o(dsp_rst), .set_stb_o(set_stb_dsp), .set_addr_o(set_addr_dsp), .set_data_o(set_data_dsp));
+
+ // Output control lines
+ wire [7:0] clock_outs, serdes_outs, adc_outs;
+ assign {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0];
+ assign {ser_enable, ser_prbsen, ser_loopen, ser_rx_en} = serdes_outs[3:0];
+ assign {adc_oe_a, adc_on_a, adc_oe_b, adc_on_b } = adc_outs[3:0];
+
+ wire phy_reset;
+ assign PHY_RESETn = ~phy_reset;
+
+ setting_reg #(.my_addr(0),.width(8)) sr_clk (.clk(wb_clk),.rst(wb_rst),.strobe(s7_ack),.addr(set_addr),
+ .in(set_data),.out(clock_outs),.changed());
+ setting_reg #(.my_addr(1),.width(8)) sr_ser (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out(serdes_outs),.changed());
+ setting_reg #(.my_addr(2),.width(8)) sr_adc (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out(adc_outs),.changed());
+ setting_reg #(.my_addr(4),.width(1)) sr_phy (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out(phy_reset),.changed());
+
+ // /////////////////////////////////////////////////////////////////////////
+ // LEDS
+ // register 8 determines whether leds are controlled by SW or not
+ // 1 = controlled by HW, 0 = by SW
+ // In Rev3 there are only 6 leds, and the highest one is on the ETH connector
+
+ wire [7:0] led_src, led_sw;
+ wire [7:0] led_hw = {run_tx, run_rx, clk_status, serdes_link_up, 1'b0};
+
+ setting_reg #(.my_addr(3),.width(8)) sr_led (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out(led_sw),.changed());
+
+ setting_reg #(.my_addr(8),.width(8), .at_reset(8'b0001_1110))
+ sr_led_src (.clk(wb_clk),.rst(wb_rst), .strobe(set_stb),.addr(set_addr), .in(set_data),.out(led_src),.changed());
+
+ assign leds = (led_src & led_hw) | (~led_src & led_sw);
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Interrupt Controller, Slave #8
+
+ // Pass interrupts on dsp_clk to wb_clk. These need edge triggering in the pic
+ wire underrun_wb, overrun_wb, pps_wb;
+
+ oneshot_2clk underrun_1s (.clk_in(dsp_clk), .in(underrun), .clk_out(wb_clk), .out(underrun_wb));
+ oneshot_2clk overrun_1s (.clk_in(dsp_clk), .in(overrun), .clk_out(wb_clk), .out(overrun_wb));
+ oneshot_2clk pps_1s (.clk_in(dsp_clk), .in(pps_int), .clk_out(wb_clk), .out(pps_wb));
+
+ assign irq= {{8'b0},
+ {8'b0},
+ {3'b0, periodic_int, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
+ {pps_wb,overrun_wb,underrun_wb,PHY_INTn,i2c_int,spi_int,onetime_int,buffer_int}};
+
+ pic pic(.clk_i(wb_clk),.rst_i(wb_rst),.cyc_i(s8_cyc),.stb_i(s8_stb),.adr_i(s8_adr[4:2]),
+ .we_i(s8_we),.dat_i(s8_dat_o),.dat_o(s8_dat_i),.ack_o(s8_ack),.int_o(proc_int),
+ .irq(irq) );
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Master Timer, Slave #9
+
+ // No longer used, replaced with simple_timer below
+ assign s9_ack = 0;
+
+ // /////////////////////////////////////////////////////////////////////////
+ // Simple Timer interrupts
+
+ simple_timer #(.BASE(SR_SIMTIMER)) simple_timer
+ (.clk(wb_clk), .reset(wb_rst),
+ .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
+ .onetime_int(onetime_int), .periodic_int(periodic_int));
+
+ // /////////////////////////////////////////////////////////////////////////
+ // UART, Slave #10
+
+ simple_uart #(.TXDEPTH(3),.RXDEPTH(3)) uart // depth of 3 is 128 entries
+ (.clk_i(wb_clk),.rst_i(wb_rst),
+ .we_i(sa_we),.stb_i(sa_stb),.cyc_i(sa_cyc),.ack_o(sa_ack),
+ .adr_i(sa_adr[4:2]),.dat_i(sa_dat_o),.dat_o(sa_dat_i),
+ .rx_int_o(uart_rx_int),.tx_int_o(uart_tx_int),
+ .tx_o(uart_tx_o),.rx_i(uart_rx_i),.baud_o(uart_baud_o));
+
+ // /////////////////////////////////////////////////////////////////////////
+ // ATR Controller, Slave #11
+
+ atr_controller atr_controller
+ (.clk_i(wb_clk),.rst_i(wb_rst),
+ .adr_i(sb_adr[5:0]),.sel_i(sb_sel),.dat_i(sb_dat_o),.dat_o(sb_dat_i),
+ .we_i(sb_we),.stb_i(sb_stb),.cyc_i(sb_cyc),.ack_o(sb_ack),
+ .run_rx(run_rx_d1),.run_tx(run_tx),.ctrl_lines(atr_lines) );
+
+ // //////////////////////////////////////////////////////////////////////////
+ // Time Sync, Slave #12
+
+ // No longer used, see time_64bit. Still need to handle mimo time, though
+ assign sc_ack = 0;
+
+ // /////////////////////////////////////////////////////////////////////////
+ // SD Card Reader / Writer, Slave #13
+
+ sd_spi_wb sd_spi_wb
+ (.clk(wb_clk),.rst(wb_rst),
+ .sd_clk(sd_clk),.sd_csn(sd_csn),.sd_mosi(sd_mosi),.sd_miso(sd_miso),
+ .wb_cyc_i(sd_cyc),.wb_stb_i(sd_stb),.wb_we_i(sd_we),
+ .wb_adr_i(sd_adr[3:2]),.wb_dat_i(sd_dat_o[7:0]),.wb_dat_o(sd_dat_i[7:0]),
+ .wb_ack_o(sd_ack) );
+
+ assign sd_dat_i[31:8] = 0;
+
+ // /////////////////////////////////////////////////////////////////////////
+ // DSP RX
+ wire [31:0] sample_rx, sample_tx;
+ wire strobe_rx, strobe_tx;
+ wire rx_dst_rdy, rx_src_rdy, rx1_dst_rdy, rx1_src_rdy;
+ wire [99:0] rx_data;
+ wire [35:0] rx1_data;
+
+ dsp_core_rx #(.BASE(SR_RX_DSP)) dsp_core_rx
+ (.clk(dsp_clk),.rst(dsp_rst),
+ .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+ .adc_a(adc_a),.adc_ovf_a(adc_ovf_a),.adc_b(adc_b),.adc_ovf_b(adc_ovf_b),
+ .sample(sample_rx), .run(run_rx_d1), .strobe(strobe_rx),
+ .debug(debug_rx_dsp) );
+
+ wire [31:0] vrc_debug;
+ wire clear_rx;
+
+ setting_reg #(.my_addr(SR_RX_CTRL+3)) sr_clear
+ (.clk(dsp_clk),.rst(dsp_rst),
+ .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
+ .out(),.changed(clear_rx));
+
+ vita_rx_control #(.BASE(SR_RX_CTRL), .WIDTH(32)) vita_rx_control
+ (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
+ .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+ .vita_time(vita_time), .overrun(overrun),
+ .sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
+ .sample_fifo_o(rx_data), .sample_fifo_dst_rdy_i(rx_dst_rdy), .sample_fifo_src_rdy_o(rx_src_rdy),
+ .debug_rx(vrc_debug));
+
+ wire [3:0] vita_state;
+
+ vita_rx_framer #(.BASE(SR_RX_CTRL), .MAXCHAN(1)) vita_rx_framer
+ (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
+ .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+ .sample_fifo_i(rx_data), .sample_fifo_dst_rdy_o(rx_dst_rdy), .sample_fifo_src_rdy_i(rx_src_rdy),
+ .data_o(rx1_data), .dst_rdy_i(rx1_dst_rdy), .src_rdy_o(rx1_src_rdy),
+ .fifo_occupied(), .fifo_full(), .fifo_empty(),
+ .debug_rx(vita_state) );
+
+ fifo_cascade #(.WIDTH(36), .SIZE(DSP_RX_FIFOSIZE)) rx_fifo_cascade
+ (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
+ .datain(rx1_data), .src_rdy_i(rx1_src_rdy), .dst_rdy_o(rx1_dst_rdy),
+ .dataout({wr1_flags,wr1_dat}), .src_rdy_o(wr1_ready_i), .dst_rdy_i(wr1_ready_o));
+
+ // ///////////////////////////////////////////////////////////////////////////////////
+ // DSP TX
+
+ wire [35:0] tx_data;
+ wire tx_src_rdy, tx_dst_rdy;
+ wire [31:0] debug_vt;
+ wire clear_tx;
+
+ setting_reg #(.my_addr(SR_TX_CTRL+1)) sr_clear_tx
+ (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out(),.changed(clear_tx));
+
+ ext_fifo #(.EXT_WIDTH(18),.INT_WIDTH(36),.RAM_DEPTH(19),.FIFO_DEPTH(19))
+ ext_fifo_i1
+ (.int_clk(dsp_clk),
+ .ext_clk(clk_to_mac),
+ .rst(dsp_rst | clear_tx),
+ .RAM_D_pi(RAM_D_pi),
+ .RAM_D_po(RAM_D_po),
+ .RAM_D_poe(RAM_D_poe),
+ .RAM_A(RAM_A),
+ .RAM_WEn(RAM_WEn),
+ .RAM_CENn(RAM_CENn),
+ .RAM_LDn(RAM_LDn),
+ .RAM_OEn(RAM_OEn),
+ .RAM_CE1n(RAM_CE1n),
+ .datain({rd1_flags[3:2],rd1_dat[31:16],rd1_flags[1:0],rd1_dat[15:0]}),
+ .src_rdy_i(rd1_ready_o),
+ .dst_rdy_o(rd1_ready_i),
+ .dataout({tx_data[35:34],tx_data[31:16],tx_data[33:32],tx_data[15:0]}),
+ .src_rdy_o(tx_src_rdy),
+ .dst_rdy_i(tx_dst_rdy),
+ .debug(debug_extfifo),
+ .debug2(debug_extfifo2) );
+
+ vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP),
+ .REPORT_ERROR(1), .DO_FLOW_CONTROL(1),
+ .PROT_ENG_FLAGS(1), .USE_TRANS_HEADER(1))
+ vita_tx_chain
+ (.clk(dsp_clk), .reset(dsp_rst),
+ .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
+ .vita_time(vita_time),
+ .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
+ .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
+ .dac_a(dac_a),.dac_b(dac_b),
+ .underrun(underrun), .run(run_tx),
+ .debug(debug_vt));
+
+ // ///////////////////////////////////////////////////////////////////////////////////
+ // SERDES
+
+ serdes #(.TXFIFOSIZE(SERDES_TX_FIFOSIZE),.RXFIFOSIZE(SERDES_RX_FIFOSIZE)) serdes
+ (.clk(dsp_clk),.rst(dsp_rst),
+ .ser_tx_clk(ser_tx_clk),.ser_t(ser_t),.ser_tklsb(ser_tklsb),.ser_tkmsb(ser_tkmsb),
+ .rd_dat_i(rd0_dat),.rd_flags_i(rd0_flags),.rd_ready_o(rd0_ready_i),.rd_ready_i(rd0_ready_o),
+ .ser_rx_clk(ser_rx_clk),.ser_r(ser_r),.ser_rklsb(ser_rklsb),.ser_rkmsb(ser_rkmsb),
+ .wr_dat_o(wr0_dat),.wr_flags_o(wr0_flags),.wr_ready_o(wr0_ready_i),.wr_ready_i(wr0_ready_o),
+ .tx_occupied(ser_tx_occ),.tx_full(ser_tx_full),.tx_empty(ser_tx_empty),
+ .rx_occupied(ser_rx_occ),.rx_full(ser_rx_full),.rx_empty(ser_rx_empty),
+ .serdes_link_up(serdes_link_up),.debug0(debug_serdes0), .debug1(debug_serdes1) );
+
+ assign RAM_CLK = clk_to_mac;
+
+ // /////////////////////////////////////////////////////////////////////////
+ // VITA Timing
+
+ time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
+ (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
+ .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int));
+
+ // /////////////////////////////////////////////////////////////////////////////////////////
+ // Debug Pins
+
+ assign debug_clk = 2'b00; // {dsp_clk, clk_to_mac};
+ assign debug = 32'd0; // debug_extfifo;
+ assign debug_gpio_0 = 32'd0;
+ assign debug_gpio_1 = 32'd0;
+
+endmodule // u2_core
diff --git a/usrp2/top/u2_rev3/u2_core_udp.v b/usrp2/top/u2_rev3/u2_core_udp.v
deleted file mode 100644
index c2d473650..000000000
--- a/usrp2/top/u2_rev3/u2_core_udp.v
+++ /dev/null
@@ -1,735 +0,0 @@
-// ////////////////////////////////////////////////////////////////////////////////
-// Module Name: u2_core
-// ////////////////////////////////////////////////////////////////////////////////
-
-module u2_core
- #(parameter RAM_SIZE=32768)
- (// Clocks
- input dsp_clk,
- input wb_clk,
- output clock_ready,
- input clk_to_mac,
- input pps_in,
-
- // Misc, debug
- output [7:0] leds,
- output [31:0] debug,
- output [1:0] debug_clk,
-
- // Expansion
- input exp_time_in,
- output exp_time_out,
-
- // GMII
- // GMII-CTRL
- input GMII_COL,
- input GMII_CRS,
-
- // GMII-TX
- output [7:0] GMII_TXD,
- output GMII_TX_EN,
- output GMII_TX_ER,
- output GMII_GTX_CLK,
- input GMII_TX_CLK, // 100mbps clk
-
- // GMII-RX
- input [7:0] GMII_RXD,
- input GMII_RX_CLK,
- input GMII_RX_DV,
- input GMII_RX_ER,
-
- // GMII-Management
- inout MDIO,
- output MDC,
- input PHY_INTn, // open drain
- output PHY_RESETn,
-
- // SERDES
- output ser_enable,
- output ser_prbsen,
- output ser_loopen,
- output ser_rx_en,
-
- output ser_tx_clk,
- output [15:0] ser_t,
- output ser_tklsb,
- output ser_tkmsb,
-
- input ser_rx_clk,
- input [15:0] ser_r,
- input ser_rklsb,
- input ser_rkmsb,
-
- // CPLD interface
- output cpld_start,
- output cpld_mode,
- output cpld_done,
- input cpld_din,
- input cpld_clk,
- input cpld_detached,
- output cpld_misc,
- input cpld_init_b,
- input por,
- output config_success,
-
- // ADC
- input [13:0] adc_a,
- input adc_ovf_a,
- output adc_on_a,
- output adc_oe_a,
-
- input [13:0] adc_b,
- input adc_ovf_b,
- output adc_on_b,
- output adc_oe_b,
-
- // DAC
- output [15:0] dac_a,
- output [15:0] dac_b,
-
- // I2C
- input scl_pad_i,
- output scl_pad_o,
- output scl_pad_oen_o,
- input sda_pad_i,
- output sda_pad_o,
- output sda_pad_oen_o,
-
- // Clock Gen Control
- output [1:0] clk_en,
- output [1:0] clk_sel,
- input clk_func, // FIXME is an input to control the 9510
- input clk_status,
-
- // Generic SPI
- output sclk,
- output mosi,
- input miso,
- output sen_clk,
- output sen_dac,
- output sen_tx_db,
- output sen_tx_adc,
- output sen_tx_dac,
- output sen_rx_db,
- output sen_rx_adc,
- output sen_rx_dac,
-
- // GPIO to DBoards
- inout [15:0] io_tx,
- inout [15:0] io_rx,
-
- // External RAM
- input [17:0] RAM_D_pi,
- output [17:0] RAM_D_po,
- output RAM_D_poe,
- output [18:0] RAM_A,
- output RAM_CE1n,
- output RAM_CENn,
- output RAM_WEn,
- output RAM_OEn,
- output RAM_LDn,
-
- // Debug stuff
- output uart_tx_o,
- input uart_rx_i,
- output uart_baud_o,
- input sim_mode,
- input [3:0] clock_divider
- );
-
- localparam SR_BUF_POOL = 64; // Uses 1 reg
- localparam SR_UDP_SM = 96; // 64 regs
- localparam SR_RX_DSP = 160; // 16
- localparam SR_RX_CTRL = 176; // 16
- localparam SR_TIME64 = 192; // 3
- localparam SR_SIMTIMER = 198; // 2
- localparam SR_TX_DSP = 208; // 16
- localparam SR_TX_CTRL = 224; // 16
-
- // FIFO Sizes, 9 = 512 lines, 10 = 1024, 11 = 2048
- // all (most?) are 36 bits wide, so 9 is 1 BRAM, 10 is 2, 11 is 4 BRAMs
- localparam DSP_TX_FIFOSIZE = 10;
- localparam DSP_RX_FIFOSIZE = 10;
- localparam ETH_TX_FIFOSIZE = 10;
- localparam ETH_RX_FIFOSIZE = 11;
- localparam SERDES_TX_FIFOSIZE = 9;
- localparam SERDES_RX_FIFOSIZE = 9; // RX currently doesn't use a fifo?
-
- wire [7:0] set_addr, set_addr_dsp;
- wire [31:0] set_data, set_data_dsp;
- wire set_stb, set_stb_dsp;
-
- wire ram_loader_done;
- wire ram_loader_rst, wb_rst, dsp_rst;
- assign dsp_rst = wb_rst;
-
- wire [31:0] status, status_b0, status_b1, status_b2, status_b3, status_b4, status_b5, status_b6, status_b7;
- wire bus_error, spi_int, i2c_int, pps_int, onetime_int, periodic_int, buffer_int;
- wire proc_int, overrun, underrun, uart_tx_int, uart_rx_int;
-
- wire [31:0] debug_gpio_0, debug_gpio_1;
- wire [31:0] atr_lines;
-
- wire [31:0] debug_rx, debug_mac, debug_mac0, debug_mac1, debug_tx_dsp, debug_txc,
- debug_serdes0, debug_serdes1, debug_serdes2, debug_rx_dsp, debug_udp, debug_extfifo, debug_extfifo2;
-
- wire [15:0] ser_rx_occ, ser_tx_occ, dsp_rx_occ, dsp_tx_occ, eth_rx_occ, eth_tx_occ, eth_rx_occ2;
- wire ser_rx_full, ser_tx_full, dsp_rx_full, dsp_tx_full, eth_rx_full, eth_tx_full, eth_rx_full2;
- wire ser_rx_empty, ser_tx_empty, dsp_rx_empty, dsp_tx_empty, eth_rx_empty, eth_tx_empty, eth_rx_empty2;
-
- wire serdes_link_up;
- wire epoch;
- wire [31:0] irq;
- wire [63:0] vita_time;
-
- wire run_rx, run_tx;
- reg run_rx_d1;
- always @(posedge dsp_clk)
- run_rx_d1 <= run_rx;
-
- // ///////////////////////////////////////////////////////////////////////////////////////////////
- // Wishbone Single Master INTERCON
- localparam dw = 32; // Data bus width
- localparam aw = 16; // Address bus width, for byte addressibility, 16 = 64K byte memory space
- localparam sw = 4; // Select width -- 32-bit data bus with 8-bit granularity.
-
- wire [dw-1:0] m0_dat_o, m0_dat_i;
- wire [dw-1:0] s0_dat_o, s1_dat_o, s0_dat_i, s1_dat_i, s2_dat_o, s3_dat_o, s2_dat_i, s3_dat_i,
- s4_dat_o, s5_dat_o, s4_dat_i, s5_dat_i, s6_dat_o, s7_dat_o, s6_dat_i, s7_dat_i,
- s8_dat_o, s9_dat_o, s8_dat_i, s9_dat_i, sa_dat_o, sa_dat_i, sb_dat_i, sb_dat_o,
- sc_dat_i, sc_dat_o, sd_dat_i, sd_dat_o, se_dat_i, se_dat_o;
- wire [aw-1:0] m0_adr,s0_adr,s1_adr,s2_adr,s3_adr,s4_adr,s5_adr,s6_adr,s7_adr,s8_adr,s9_adr,sa_adr,sb_adr,sc_adr, sd_adr, se_adr;
- wire [sw-1:0] m0_sel,s0_sel,s1_sel,s2_sel,s3_sel,s4_sel,s5_sel,s6_sel,s7_sel,s8_sel,s9_sel,sa_sel,sb_sel,sc_sel, sd_sel, se_sel;
- wire m0_ack,s0_ack,s1_ack,s2_ack,s3_ack,s4_ack,s5_ack,s6_ack,s7_ack,s8_ack,s9_ack,sa_ack,sb_ack,sc_ack, sd_ack, se_ack;
- wire m0_stb,s0_stb,s1_stb,s2_stb,s3_stb,s4_stb,s5_stb,s6_stb,s7_stb,s8_stb,s9_stb,sa_stb,sb_stb,sc_stb, sd_stb, se_stb;
- wire m0_cyc,s0_cyc,s1_cyc,s2_cyc,s3_cyc,s4_cyc,s5_cyc,s6_cyc,s7_cyc,s8_cyc,s9_cyc,sa_cyc,sb_cyc,sc_cyc, sd_cyc, se_cyc;
- wire m0_err, m0_rty;
- wire m0_we,s0_we,s1_we,s2_we,s3_we,s4_we,s5_we,s6_we,s7_we,s8_we,s9_we,sa_we,sb_we,sc_we,sd_we, se_we;
-
- wb_1master #(.decode_w(6),
- .s0_addr(6'b0000_00),.s0_mask(6'b100000),
- .s1_addr(6'b1000_00),.s1_mask(6'b110000),
- .s2_addr(6'b1100_00),.s2_mask(6'b111111),
- .s3_addr(6'b1100_01),.s3_mask(6'b111111),
- .s4_addr(6'b1100_10),.s4_mask(6'b111111),
- .s5_addr(6'b1100_11),.s5_mask(6'b111111),
- .s6_addr(6'b1101_00),.s6_mask(6'b111111),
- .s7_addr(6'b1101_01),.s7_mask(6'b111111),
- .s8_addr(6'b1101_10),.s8_mask(6'b111111),
- .s9_addr(6'b1101_11),.s9_mask(6'b111111),
- .sa_addr(6'b1110_00),.sa_mask(6'b111111),
- .sb_addr(6'b1110_01),.sb_mask(6'b111111),
- .sc_addr(6'b1110_10),.sc_mask(6'b111111),
- .sd_addr(6'b1110_11),.sd_mask(6'b111111),
- .se_addr(6'b1111_00),.se_mask(6'b111111),
- .sf_addr(6'b1111_01),.sf_mask(6'b111111),
- .dw(dw),.aw(aw),.sw(sw)) wb_1master
- (.clk_i(wb_clk),.rst_i(wb_rst),
- .m0_dat_o(m0_dat_o),.m0_ack_o(m0_ack),.m0_err_o(m0_err),.m0_rty_o(m0_rty),.m0_dat_i(m0_dat_i),
- .m0_adr_i(m0_adr),.m0_sel_i(m0_sel),.m0_we_i(m0_we),.m0_cyc_i(m0_cyc),.m0_stb_i(m0_stb),
- .s0_dat_o(s0_dat_o),.s0_adr_o(s0_adr),.s0_sel_o(s0_sel),.s0_we_o (s0_we),.s0_cyc_o(s0_cyc),.s0_stb_o(s0_stb),
- .s0_dat_i(s0_dat_i),.s0_ack_i(s0_ack),.s0_err_i(0),.s0_rty_i(0),
- .s1_dat_o(s1_dat_o),.s1_adr_o(s1_adr),.s1_sel_o(s1_sel),.s1_we_o (s1_we),.s1_cyc_o(s1_cyc),.s1_stb_o(s1_stb),
- .s1_dat_i(s1_dat_i),.s1_ack_i(s1_ack),.s1_err_i(0),.s1_rty_i(0),
- .s2_dat_o(s2_dat_o),.s2_adr_o(s2_adr),.s2_sel_o(s2_sel),.s2_we_o (s2_we),.s2_cyc_o(s2_cyc),.s2_stb_o(s2_stb),
- .s2_dat_i(s2_dat_i),.s2_ack_i(s2_ack),.s2_err_i(0),.s2_rty_i(0),
- .s3_dat_o(s3_dat_o),.s3_adr_o(s3_adr),.s3_sel_o(s3_sel),.s3_we_o (s3_we),.s3_cyc_o(s3_cyc),.s3_stb_o(s3_stb),
- .s3_dat_i(s3_dat_i),.s3_ack_i(s3_ack),.s3_err_i(0),.s3_rty_i(0),
- .s4_dat_o(s4_dat_o),.s4_adr_o(s4_adr),.s4_sel_o(s4_sel),.s4_we_o (s4_we),.s4_cyc_o(s4_cyc),.s4_stb_o(s4_stb),
- .s4_dat_i(s4_dat_i),.s4_ack_i(s4_ack),.s4_err_i(0),.s4_rty_i(0),
- .s5_dat_o(s5_dat_o),.s5_adr_o(s5_adr),.s5_sel_o(s5_sel),.s5_we_o (s5_we),.s5_cyc_o(s5_cyc),.s5_stb_o(s5_stb),
- .s5_dat_i(s5_dat_i),.s5_ack_i(s5_ack),.s5_err_i(0),.s5_rty_i(0),
- .s6_dat_o(s6_dat_o),.s6_adr_o(s6_adr),.s6_sel_o(s6_sel),.s6_we_o (s6_we),.s6_cyc_o(s6_cyc),.s6_stb_o(s6_stb),
- .s6_dat_i(s6_dat_i),.s6_ack_i(s6_ack),.s6_err_i(0),.s6_rty_i(0),
- .s7_dat_o(s7_dat_o),.s7_adr_o(s7_adr),.s7_sel_o(s7_sel),.s7_we_o (s7_we),.s7_cyc_o(s7_cyc),.s7_stb_o(s7_stb),
- .s7_dat_i(s7_dat_i),.s7_ack_i(s7_ack),.s7_err_i(0),.s7_rty_i(0),
- .s8_dat_o(s8_dat_o),.s8_adr_o(s8_adr),.s8_sel_o(s8_sel),.s8_we_o (s8_we),.s8_cyc_o(s8_cyc),.s8_stb_o(s8_stb),
- .s8_dat_i(s8_dat_i),.s8_ack_i(s8_ack),.s8_err_i(0),.s8_rty_i(0),
- .s9_dat_o(s9_dat_o),.s9_adr_o(s9_adr),.s9_sel_o(s9_sel),.s9_we_o (s9_we),.s9_cyc_o(s9_cyc),.s9_stb_o(s9_stb),
- .s9_dat_i(s9_dat_i),.s9_ack_i(s9_ack),.s9_err_i(0),.s9_rty_i(0),
- .sa_dat_o(sa_dat_o),.sa_adr_o(sa_adr),.sa_sel_o(sa_sel),.sa_we_o(sa_we),.sa_cyc_o(sa_cyc),.sa_stb_o(sa_stb),
- .sa_dat_i(sa_dat_i),.sa_ack_i(sa_ack),.sa_err_i(0),.sa_rty_i(0),
- .sb_dat_o(sb_dat_o),.sb_adr_o(sb_adr),.sb_sel_o(sb_sel),.sb_we_o(sb_we),.sb_cyc_o(sb_cyc),.sb_stb_o(sb_stb),
- .sb_dat_i(sb_dat_i),.sb_ack_i(sb_ack),.sb_err_i(0),.sb_rty_i(0),
- .sc_dat_o(sc_dat_o),.sc_adr_o(sc_adr),.sc_sel_o(sc_sel),.sc_we_o(sc_we),.sc_cyc_o(sc_cyc),.sc_stb_o(sc_stb),
- .sc_dat_i(sc_dat_i),.sc_ack_i(sc_ack),.sc_err_i(0),.sc_rty_i(0),
- .sd_dat_o(sd_dat_o),.sd_adr_o(sd_adr),.sd_sel_o(sd_sel),.sd_we_o(sd_we),.sd_cyc_o(sd_cyc),.sd_stb_o(sd_stb),
- .sd_dat_i(sd_dat_i),.sd_ack_i(sd_ack),.sd_err_i(0),.sd_rty_i(0),
- .se_dat_o(se_dat_o),.se_adr_o(se_adr),.se_sel_o(se_sel),.se_we_o(se_we),.se_cyc_o(se_cyc),.se_stb_o(se_stb),
- .se_dat_i(se_dat_i),.se_ack_i(se_ack),.se_err_i(0),.se_rty_i(0),
- .sf_dat_i(0),.sf_ack_i(0),.sf_err_i(0),.sf_rty_i(0) );
-
- //////////////////////////////////////////////////////////////////////////////////////////
- // Reset Controller
- system_control sysctrl (.wb_clk_i(wb_clk), // .por_i(por),
- .ram_loader_rst_o(ram_loader_rst),
- .wb_rst_o(wb_rst),
- .ram_loader_done_i(ram_loader_done));
-
- assign config_success = ram_loader_done;
- reg takeover = 0;
-
- wire cpld_start_int, cpld_mode_int, cpld_done_int;
-
- always @(posedge wb_clk)
- if(ram_loader_done)
- takeover = 1;
- assign cpld_misc = ~takeover;
-
- wire sd_clk, sd_csn, sd_mosi, sd_miso;
-
- assign sd_miso = cpld_din;
- assign cpld_start = takeover ? sd_clk : cpld_start_int;
- assign cpld_mode = takeover ? sd_csn : cpld_mode_int;
- assign cpld_done = takeover ? sd_mosi : cpld_done_int;
-
- // ///////////////////////////////////////////////////////////////////
- // RAM Loader
-
- wire [31:0] ram_loader_dat, if_dat;
- wire [15:0] ram_loader_adr;
- wire [14:0] if_adr;
- wire [3:0] ram_loader_sel;
- wire ram_loader_stb, ram_loader_we;
- wire iwb_ack, iwb_stb;
- ram_loader #(.AWIDTH(16),.RAM_SIZE(RAM_SIZE))
- ram_loader (.wb_clk(wb_clk),.dsp_clk(dsp_clk),.ram_loader_rst(ram_loader_rst),
- .wb_dat(ram_loader_dat),.wb_adr(ram_loader_adr),
- .wb_stb(ram_loader_stb),.wb_sel(ram_loader_sel),
- .wb_we(ram_loader_we),
- .ram_loader_done(ram_loader_done),
- // CPLD Interface
- .cpld_clk(cpld_clk),
- .cpld_din(cpld_din),
- .cpld_start(cpld_start_int),
- .cpld_mode(cpld_mode_int),
- .cpld_done(cpld_done_int),
- .cpld_detached(cpld_detached));
-
- // /////////////////////////////////////////////////////////////////////////
- // Processor
- aeMB_core_BE #(.ISIZ(16),.DSIZ(16),.MUL(0),.BSF(1))
- aeMB (.sys_clk_i(wb_clk), .sys_rst_i(wb_rst),
- // Instruction Wishbone bus to I-RAM
- .if_adr(if_adr),
- .if_dat(if_dat),
- // Data Wishbone bus to system bus fabric
- .dwb_we_o(m0_we),.dwb_stb_o(m0_stb),.dwb_dat_o(m0_dat_i),.dwb_adr_o(m0_adr),
- .dwb_dat_i(m0_dat_o),.dwb_ack_i(m0_ack),.dwb_sel_o(m0_sel),.dwb_cyc_o(m0_cyc),
- // Interrupts and exceptions
- .sys_int_i(proc_int),.sys_exc_i(bus_error) );
-
- assign bus_error = m0_err | m0_rty;
-
- // /////////////////////////////////////////////////////////////////////////
- // Dual Ported RAM -- D-Port is Slave #0 on main Wishbone
- // I-port connects directly to processor and ram loader
-
- wire flush_icache;
- ram_harvard #(.AWIDTH(15),.RAM_SIZE(RAM_SIZE),.ICWIDTH(7),.DCWIDTH(6))
- sys_ram(.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
-
- .ram_loader_adr_i(ram_loader_adr[14:0]), .ram_loader_dat_i(ram_loader_dat),
- .ram_loader_stb_i(ram_loader_stb), .ram_loader_sel_i(ram_loader_sel),
- .ram_loader_we_i(ram_loader_we),
- .ram_loader_done_i(ram_loader_done),
-
- .if_adr(if_adr),
- .if_data(if_dat),
-
- .dwb_adr_i(s0_adr[14:0]), .dwb_dat_i(s0_dat_o), .dwb_dat_o(s0_dat_i),
- .dwb_we_i(s0_we), .dwb_ack_o(s0_ack), .dwb_stb_i(s0_stb), .dwb_sel_i(s0_sel),
- .flush_icache(flush_icache));
-
- setting_reg #(.my_addr(7)) sr_icache (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(),.changed(flush_icache));
-
- // /////////////////////////////////////////////////////////////////////////
- // Buffer Pool, slave #1
- wire rd0_ready_i, rd0_ready_o;
- wire rd1_ready_i, rd1_ready_o;
- wire rd2_ready_i, rd2_ready_o;
- wire rd3_ready_i, rd3_ready_o;
- wire [3:0] rd0_flags, rd1_flags, rd2_flags, rd3_flags;
- wire [31:0] rd0_dat, rd1_dat, rd2_dat, rd3_dat;
-
- wire wr0_ready_i, wr0_ready_o;
- wire wr1_ready_i, wr1_ready_o;
- wire wr2_ready_i, wr2_ready_o;
- wire wr3_ready_i, wr3_ready_o;
- wire [3:0] wr0_flags, wr1_flags, wr2_flags, wr3_flags;
- wire [31:0] wr0_dat, wr1_dat, wr2_dat, wr3_dat;
-
- buffer_pool #(.BUF_SIZE(9), .SET_ADDR(SR_BUF_POOL)) buffer_pool
- (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),
- .wb_we_i(s1_we),.wb_stb_i(s1_stb),.wb_adr_i(s1_adr),.wb_dat_i(s1_dat_o),
- .wb_dat_o(s1_dat_i),.wb_ack_o(s1_ack),.wb_err_o(),.wb_rty_o(),
-
- .stream_clk(dsp_clk), .stream_rst(dsp_rst),
- .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
- .status(status),.sys_int_o(buffer_int),
-
- .s0(status_b0),.s1(status_b1),.s2(status_b2),.s3(status_b3),
- .s4(status_b4),.s5(status_b5),.s6(status_b6),.s7(status_b7),
-
- // Write Interfaces
- .wr0_data_i(wr0_dat), .wr0_flags_i(wr0_flags), .wr0_ready_i(wr0_ready_i), .wr0_ready_o(wr0_ready_o),
- .wr1_data_i(wr1_dat), .wr1_flags_i(wr1_flags), .wr1_ready_i(wr1_ready_i), .wr1_ready_o(wr1_ready_o),
- .wr2_data_i(wr2_dat), .wr2_flags_i(wr2_flags), .wr2_ready_i(wr2_ready_i), .wr2_ready_o(wr2_ready_o),
- .wr3_data_i(wr3_dat), .wr3_flags_i(wr3_flags), .wr3_ready_i(wr3_ready_i), .wr3_ready_o(wr3_ready_o),
- // Read Interfaces
- .rd0_data_o(rd0_dat), .rd0_flags_o(rd0_flags), .rd0_ready_i(rd0_ready_i), .rd0_ready_o(rd0_ready_o),
- .rd1_data_o(rd1_dat), .rd1_flags_o(rd1_flags), .rd1_ready_i(rd1_ready_i), .rd1_ready_o(rd1_ready_o),
- .rd2_data_o(rd2_dat), .rd2_flags_o(rd2_flags), .rd2_ready_i(rd2_ready_i), .rd2_ready_o(rd2_ready_o),
- .rd3_data_o(rd3_dat), .rd3_flags_o(rd3_flags), .rd3_ready_i(rd3_ready_i), .rd3_ready_o(rd3_ready_o)
- );
-
- wire [31:0] status_enc;
- priority_enc priority_enc (.in({16'b0,status[15:0]}), .out(status_enc));
-
- // /////////////////////////////////////////////////////////////////////////
- // SPI -- Slave #2
- spi_top shared_spi
- (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.wb_adr_i(s2_adr[4:0]),.wb_dat_i(s2_dat_o),
- .wb_dat_o(s2_dat_i),.wb_sel_i(s2_sel),.wb_we_i(s2_we),.wb_stb_i(s2_stb),
- .wb_cyc_i(s2_cyc),.wb_ack_o(s2_ack),.wb_err_o(),.wb_int_o(spi_int),
- .ss_pad_o({sen_tx_db,sen_tx_adc,sen_tx_dac,sen_rx_db,sen_rx_adc,sen_rx_dac,sen_dac,sen_clk}),
- .sclk_pad_o(sclk),.mosi_pad_o(mosi),.miso_pad_i(miso) );
-
- // /////////////////////////////////////////////////////////////////////////
- // I2C -- Slave #3
- i2c_master_top #(.ARST_LVL(1))
- i2c (.wb_clk_i(wb_clk),.wb_rst_i(wb_rst),.arst_i(1'b0),
- .wb_adr_i(s3_adr[4:2]),.wb_dat_i(s3_dat_o[7:0]),.wb_dat_o(s3_dat_i[7:0]),
- .wb_we_i(s3_we),.wb_stb_i(s3_stb),.wb_cyc_i(s3_cyc),
- .wb_ack_o(s3_ack),.wb_inta_o(i2c_int),
- .scl_pad_i(scl_pad_i),.scl_pad_o(scl_pad_o),.scl_padoen_o(scl_pad_oen_o),
- .sda_pad_i(sda_pad_i),.sda_pad_o(sda_pad_o),.sda_padoen_o(sda_pad_oen_o) );
-
- assign s3_dat_i[31:8] = 24'd0;
-
- // /////////////////////////////////////////////////////////////////////////
- // GPIOs -- Slave #4
- nsgpio nsgpio(.clk_i(wb_clk),.rst_i(wb_rst),
- .cyc_i(s4_cyc),.stb_i(s4_stb),.adr_i(s4_adr[3:0]),.we_i(s4_we),
- .dat_i(s4_dat_o),.dat_o(s4_dat_i),.ack_o(s4_ack),
- .atr(atr_lines),.debug_0(debug_gpio_0),.debug_1(debug_gpio_1),
- .gpio({io_tx,io_rx}) );
-
- // /////////////////////////////////////////////////////////////////////////
- // Buffer Pool Status -- Slave #5
-
- reg [31:0] cycle_count;
- always @(posedge wb_clk)
- if(wb_rst)
- cycle_count <= 0;
- else
- cycle_count <= cycle_count + 1;
-
- //compatibility number -> increment when the fpga has been sufficiently altered
- localparam compat_num = 32'd3;
-
- wb_readback_mux buff_pool_status
- (.wb_clk_i(wb_clk), .wb_rst_i(wb_rst), .wb_stb_i(s5_stb),
- .wb_adr_i(s5_adr), .wb_dat_o(s5_dat_i), .wb_ack_o(s5_ack),
-
- .word00(status_b0),.word01(status_b1),.word02(status_b2),.word03(status_b3),
- .word04(status_b4),.word05(status_b5),.word06(status_b6),.word07(status_b7),
- .word08(status),.word09({sim_mode,27'b0,clock_divider[3:0]}),.word10(vita_time[63:32]),
- .word11(vita_time[31:0]),.word12(compat_num),.word13(irq),.word14(status_enc),.word15(cycle_count)
- );
-
- // /////////////////////////////////////////////////////////////////////////
- // Ethernet MAC Slave #6
-
- wire [18:0] rx_f19_data, tx_f19_data;
- wire rx_f19_src_rdy, rx_f19_dst_rdy, rx_f36_src_rdy, rx_f36_dst_rdy;
-
- simple_gemac_wrapper19 #(.RXFIFOSIZE(11), .TXFIFOSIZE(6)) simple_gemac_wrapper19
- (.clk125(clk_to_mac), .reset(wb_rst),
- .GMII_GTX_CLK(GMII_GTX_CLK), .GMII_TX_EN(GMII_TX_EN),
- .GMII_TX_ER(GMII_TX_ER), .GMII_TXD(GMII_TXD),
- .GMII_RX_CLK(GMII_RX_CLK), .GMII_RX_DV(GMII_RX_DV),
- .GMII_RX_ER(GMII_RX_ER), .GMII_RXD(GMII_RXD),
- .sys_clk(dsp_clk),
- .rx_f19_data(rx_f19_data), .rx_f19_src_rdy(rx_f19_src_rdy), .rx_f19_dst_rdy(rx_f19_dst_rdy),
- .tx_f19_data(tx_f19_data), .tx_f19_src_rdy(tx_f19_src_rdy), .tx_f19_dst_rdy(tx_f19_dst_rdy),
- .wb_clk(wb_clk), .wb_rst(wb_rst), .wb_stb(s6_stb), .wb_cyc(s6_cyc), .wb_ack(s6_ack),
- .wb_we(s6_we), .wb_adr(s6_adr), .wb_dat_i(s6_dat_o), .wb_dat_o(s6_dat_i),
- .mdio(MDIO), .mdc(MDC),
- .debug(debug_mac));
-
- wire [35:0] udp_tx_data, udp_rx_data;
- wire udp_tx_src_rdy, udp_tx_dst_rdy, udp_rx_src_rdy, udp_rx_dst_rdy;
-
- udp_wrapper #(.BASE(SR_UDP_SM)) udp_wrapper
- (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
- .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
- .rx_f19_data(rx_f19_data), .rx_f19_src_rdy_i(rx_f19_src_rdy), .rx_f19_dst_rdy_o(rx_f19_dst_rdy),
- .tx_f19_data(tx_f19_data), .tx_f19_src_rdy_o(tx_f19_src_rdy), .tx_f19_dst_rdy_i(tx_f19_dst_rdy),
- .rx_f36_data(udp_rx_data), .rx_f36_src_rdy_o(udp_rx_src_rdy), .rx_f36_dst_rdy_i(udp_rx_dst_rdy),
- .tx_f36_data(udp_tx_data), .tx_f36_src_rdy_i(udp_tx_src_rdy), .tx_f36_dst_rdy_o(udp_tx_dst_rdy),
- .debug(debug_udp) );
-
- wire [35:0] tx_err_data, udp1_tx_data;
- wire tx_err_src_rdy, tx_err_dst_rdy, udp1_tx_src_rdy, udp1_tx_dst_rdy;
-
- fifo_cascade #(.WIDTH(36), .SIZE(ETH_TX_FIFOSIZE)) tx_eth_fifo
- (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
- .datain({rd2_flags,rd2_dat}), .src_rdy_i(rd2_ready_o), .dst_rdy_o(rd2_ready_i),
- .dataout(udp1_tx_data), .src_rdy_o(udp1_tx_src_rdy), .dst_rdy_i(udp1_tx_dst_rdy));
-
- fifo36_mux #(.prio(0)) mux_err_stream
- (.clk(dsp_clk), .reset(dsp_reset), .clear(0),
- .data0_i(udp1_tx_data), .src0_rdy_i(udp1_tx_src_rdy), .dst0_rdy_o(udp1_tx_dst_rdy),
- .data1_i(tx_err_data), .src1_rdy_i(tx_err_src_rdy), .dst1_rdy_o(tx_err_dst_rdy),
- .data_o(udp_tx_data), .src_rdy_o(udp_tx_src_rdy), .dst_rdy_i(udp_tx_dst_rdy));
-
- fifo_cascade #(.WIDTH(36), .SIZE(ETH_RX_FIFOSIZE)) rx_eth_fifo
- (.clk(dsp_clk), .reset(dsp_rst), .clear(0),
- .datain(udp_rx_data), .src_rdy_i(udp_rx_src_rdy), .dst_rdy_o(udp_rx_dst_rdy),
- .dataout({wr2_flags,wr2_dat}), .src_rdy_o(wr2_ready_i), .dst_rdy_i(wr2_ready_o));
-
- // /////////////////////////////////////////////////////////////////////////
- // Settings Bus -- Slave #7
- settings_bus settings_bus
- (.wb_clk(wb_clk),.wb_rst(wb_rst),.wb_adr_i(s7_adr),.wb_dat_i(s7_dat_o),
- .wb_stb_i(s7_stb),.wb_we_i(s7_we),.wb_ack_o(s7_ack),
- .strobe(set_stb),.addr(set_addr),.data(set_data));
-
- assign s7_dat_i = 32'd0;
-
- settings_bus_crossclock settings_bus_crossclock
- (.clk_i(wb_clk), .rst_i(wb_rst), .set_stb_i(set_stb), .set_addr_i(set_addr), .set_data_i(set_data),
- .clk_o(dsp_clk), .rst_o(dsp_rst), .set_stb_o(set_stb_dsp), .set_addr_o(set_addr_dsp), .set_data_o(set_data_dsp));
-
- // Output control lines
- wire [7:0] clock_outs, serdes_outs, adc_outs;
- assign {clock_ready, clk_en[1:0], clk_sel[1:0]} = clock_outs[4:0];
- assign {ser_enable, ser_prbsen, ser_loopen, ser_rx_en} = serdes_outs[3:0];
- assign {adc_oe_a, adc_on_a, adc_oe_b, adc_on_b } = adc_outs[3:0];
-
- wire phy_reset;
- assign PHY_RESETn = ~phy_reset;
-
- setting_reg #(.my_addr(0),.width(8)) sr_clk (.clk(wb_clk),.rst(wb_rst),.strobe(s7_ack),.addr(set_addr),
- .in(set_data),.out(clock_outs),.changed());
- setting_reg #(.my_addr(1),.width(8)) sr_ser (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(serdes_outs),.changed());
- setting_reg #(.my_addr(2),.width(8)) sr_adc (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(adc_outs),.changed());
- setting_reg #(.my_addr(4),.width(1)) sr_phy (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(phy_reset),.changed());
-
- // /////////////////////////////////////////////////////////////////////////
- // LEDS
- // register 8 determines whether leds are controlled by SW or not
- // 1 = controlled by HW, 0 = by SW
- // In Rev3 there are only 6 leds, and the highest one is on the ETH connector
-
- wire [7:0] led_src, led_sw;
- wire [7:0] led_hw = {run_tx, run_rx, clk_status, serdes_link_up, 1'b0};
-
- setting_reg #(.my_addr(3),.width(8)) sr_led (.clk(wb_clk),.rst(wb_rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(led_sw),.changed());
-
- setting_reg #(.my_addr(8),.width(8), .at_reset(8'b0001_1110))
- sr_led_src (.clk(wb_clk),.rst(wb_rst), .strobe(set_stb),.addr(set_addr), .in(set_data),.out(led_src),.changed());
-
- assign leds = (led_src & led_hw) | (~led_src & led_sw);
-
- // /////////////////////////////////////////////////////////////////////////
- // Interrupt Controller, Slave #8
-
- // Pass interrupts on dsp_clk to wb_clk. These need edge triggering in the pic
- wire underrun_wb, overrun_wb, pps_wb;
-
- oneshot_2clk underrun_1s (.clk_in(dsp_clk), .in(underrun), .clk_out(wb_clk), .out(underrun_wb));
- oneshot_2clk overrun_1s (.clk_in(dsp_clk), .in(overrun), .clk_out(wb_clk), .out(overrun_wb));
- oneshot_2clk pps_1s (.clk_in(dsp_clk), .in(pps_int), .clk_out(wb_clk), .out(pps_wb));
-
- assign irq= {{8'b0},
- {8'b0},
- {3'b0, periodic_int, clk_status, serdes_link_up, uart_tx_int, uart_rx_int},
- {pps_wb,overrun_wb,underrun_wb,PHY_INTn,i2c_int,spi_int,onetime_int,buffer_int}};
-
- pic pic(.clk_i(wb_clk),.rst_i(wb_rst),.cyc_i(s8_cyc),.stb_i(s8_stb),.adr_i(s8_adr[4:2]),
- .we_i(s8_we),.dat_i(s8_dat_o),.dat_o(s8_dat_i),.ack_o(s8_ack),.int_o(proc_int),
- .irq(irq) );
-
- // /////////////////////////////////////////////////////////////////////////
- // Master Timer, Slave #9
-
- // No longer used, replaced with simple_timer below
- assign s9_ack = 0;
-
- // /////////////////////////////////////////////////////////////////////////
- // Simple Timer interrupts
-
- simple_timer #(.BASE(SR_SIMTIMER)) simple_timer
- (.clk(wb_clk), .reset(wb_rst),
- .set_stb(set_stb), .set_addr(set_addr), .set_data(set_data),
- .onetime_int(onetime_int), .periodic_int(periodic_int));
-
- // /////////////////////////////////////////////////////////////////////////
- // UART, Slave #10
-
- simple_uart #(.TXDEPTH(3),.RXDEPTH(3)) uart // depth of 3 is 128 entries
- (.clk_i(wb_clk),.rst_i(wb_rst),
- .we_i(sa_we),.stb_i(sa_stb),.cyc_i(sa_cyc),.ack_o(sa_ack),
- .adr_i(sa_adr[4:2]),.dat_i(sa_dat_o),.dat_o(sa_dat_i),
- .rx_int_o(uart_rx_int),.tx_int_o(uart_tx_int),
- .tx_o(uart_tx_o),.rx_i(uart_rx_i),.baud_o(uart_baud_o));
-
- // /////////////////////////////////////////////////////////////////////////
- // ATR Controller, Slave #11
-
- atr_controller atr_controller
- (.clk_i(wb_clk),.rst_i(wb_rst),
- .adr_i(sb_adr[5:0]),.sel_i(sb_sel),.dat_i(sb_dat_o),.dat_o(sb_dat_i),
- .we_i(sb_we),.stb_i(sb_stb),.cyc_i(sb_cyc),.ack_o(sb_ack),
- .run_rx(run_rx_d1),.run_tx(run_tx),.ctrl_lines(atr_lines) );
-
- // //////////////////////////////////////////////////////////////////////////
- // Time Sync, Slave #12
-
- // No longer used, see time_64bit. Still need to handle mimo time, though
- assign sc_ack = 0;
-
- // /////////////////////////////////////////////////////////////////////////
- // SD Card Reader / Writer, Slave #13
-
- sd_spi_wb sd_spi_wb
- (.clk(wb_clk),.rst(wb_rst),
- .sd_clk(sd_clk),.sd_csn(sd_csn),.sd_mosi(sd_mosi),.sd_miso(sd_miso),
- .wb_cyc_i(sd_cyc),.wb_stb_i(sd_stb),.wb_we_i(sd_we),
- .wb_adr_i(sd_adr[3:2]),.wb_dat_i(sd_dat_o[7:0]),.wb_dat_o(sd_dat_i[7:0]),
- .wb_ack_o(sd_ack) );
-
- assign sd_dat_i[31:8] = 0;
-
- // /////////////////////////////////////////////////////////////////////////
- // DSP RX
- wire [31:0] sample_rx, sample_tx;
- wire strobe_rx, strobe_tx;
- wire rx_dst_rdy, rx_src_rdy, rx1_dst_rdy, rx1_src_rdy;
- wire [99:0] rx_data;
- wire [35:0] rx1_data;
-
- dsp_core_rx #(.BASE(SR_RX_DSP)) dsp_core_rx
- (.clk(dsp_clk),.rst(dsp_rst),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .adc_a(adc_a),.adc_ovf_a(adc_ovf_a),.adc_b(adc_b),.adc_ovf_b(adc_ovf_b),
- .sample(sample_rx), .run(run_rx_d1), .strobe(strobe_rx),
- .debug(debug_rx_dsp) );
-
- wire [31:0] vrc_debug;
- wire clear_rx;
-
- setting_reg #(.my_addr(SR_RX_CTRL+3)) sr_clear
- (.clk(dsp_clk),.rst(dsp_rst),
- .strobe(set_stb_dsp),.addr(set_addr_dsp),.in(set_data_dsp),
- .out(),.changed(clear_rx));
-
- vita_rx_control #(.BASE(SR_RX_CTRL), .WIDTH(32)) vita_rx_control
- (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .vita_time(vita_time), .overrun(overrun),
- .sample(sample_rx), .run(run_rx), .strobe(strobe_rx),
- .sample_fifo_o(rx_data), .sample_fifo_dst_rdy_i(rx_dst_rdy), .sample_fifo_src_rdy_o(rx_src_rdy),
- .debug_rx(vrc_debug));
-
- wire [3:0] vita_state;
-
- vita_rx_framer #(.BASE(SR_RX_CTRL), .MAXCHAN(1)) vita_rx_framer
- (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .sample_fifo_i(rx_data), .sample_fifo_dst_rdy_o(rx_dst_rdy), .sample_fifo_src_rdy_i(rx_src_rdy),
- .data_o(rx1_data), .dst_rdy_i(rx1_dst_rdy), .src_rdy_o(rx1_src_rdy),
- .fifo_occupied(), .fifo_full(), .fifo_empty(),
- .debug_rx(vita_state) );
-
- fifo_cascade #(.WIDTH(36), .SIZE(DSP_RX_FIFOSIZE)) rx_fifo_cascade
- (.clk(dsp_clk), .reset(dsp_rst), .clear(clear_rx),
- .datain(rx1_data), .src_rdy_i(rx1_src_rdy), .dst_rdy_o(rx1_dst_rdy),
- .dataout({wr1_flags,wr1_dat}), .src_rdy_o(wr1_ready_i), .dst_rdy_i(wr1_ready_o));
-
- // ///////////////////////////////////////////////////////////////////////////////////
- // DSP TX
-
- wire [35:0] tx_data;
- wire tx_src_rdy, tx_dst_rdy;
- wire [31:0] debug_vt;
- wire clear_tx;
-
- setting_reg #(.my_addr(SR_TX_CTRL+1)) sr_clear_tx
- (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
- .in(set_data),.out(),.changed(clear_tx));
-
- ext_fifo #(.EXT_WIDTH(18),.INT_WIDTH(36),.RAM_DEPTH(19),.FIFO_DEPTH(19))
- ext_fifo_i1
- (.int_clk(dsp_clk),
- .ext_clk(clk_to_mac),
- .rst(dsp_rst | clear_tx),
- .RAM_D_pi(RAM_D_pi),
- .RAM_D_po(RAM_D_po),
- .RAM_D_poe(RAM_D_poe),
- .RAM_A(RAM_A),
- .RAM_WEn(RAM_WEn),
- .RAM_CENn(RAM_CENn),
- .RAM_LDn(RAM_LDn),
- .RAM_OEn(RAM_OEn),
- .RAM_CE1n(RAM_CE1n),
- .datain({rd1_flags[3:2],rd1_dat[31:16],rd1_flags[1:0],rd1_dat[15:0]}),
- .src_rdy_i(rd1_ready_o),
- .dst_rdy_o(rd1_ready_i),
- .dataout({tx_data[35:34],tx_data[31:16],tx_data[33:32],tx_data[15:0]}),
- .src_rdy_o(tx_src_rdy),
- .dst_rdy_i(tx_dst_rdy),
- .debug(debug_extfifo),
- .debug2(debug_extfifo2) );
-
- vita_tx_chain #(.BASE_CTRL(SR_TX_CTRL), .BASE_DSP(SR_TX_DSP),
- .REPORT_ERROR(1), .DO_FLOW_CONTROL(1),
- .PROT_ENG_FLAGS(1), .USE_TRANS_HEADER(1))
- vita_tx_chain
- (.clk(dsp_clk), .reset(dsp_rst),
- .set_stb(set_stb_dsp),.set_addr(set_addr_dsp),.set_data(set_data_dsp),
- .vita_time(vita_time),
- .tx_data_i(tx_data), .tx_src_rdy_i(tx_src_rdy), .tx_dst_rdy_o(tx_dst_rdy),
- .err_data_o(tx_err_data), .err_src_rdy_o(tx_err_src_rdy), .err_dst_rdy_i(tx_err_dst_rdy),
- .dac_a(dac_a),.dac_b(dac_b),
- .underrun(underrun), .run(run_tx),
- .debug(debug_vt));
-
- // ///////////////////////////////////////////////////////////////////////////////////
- // SERDES
-
- serdes #(.TXFIFOSIZE(SERDES_TX_FIFOSIZE),.RXFIFOSIZE(SERDES_RX_FIFOSIZE)) serdes
- (.clk(dsp_clk),.rst(dsp_rst),
- .ser_tx_clk(ser_tx_clk),.ser_t(ser_t),.ser_tklsb(ser_tklsb),.ser_tkmsb(ser_tkmsb),
- .rd_dat_i(rd0_dat),.rd_flags_i(rd0_flags),.rd_ready_o(rd0_ready_i),.rd_ready_i(rd0_ready_o),
- .ser_rx_clk(ser_rx_clk),.ser_r(ser_r),.ser_rklsb(ser_rklsb),.ser_rkmsb(ser_rkmsb),
- .wr_dat_o(wr0_dat),.wr_flags_o(wr0_flags),.wr_ready_o(wr0_ready_i),.wr_ready_i(wr0_ready_o),
- .tx_occupied(ser_tx_occ),.tx_full(ser_tx_full),.tx_empty(ser_tx_empty),
- .rx_occupied(ser_rx_occ),.rx_full(ser_rx_full),.rx_empty(ser_rx_empty),
- .serdes_link_up(serdes_link_up),.debug0(debug_serdes0), .debug1(debug_serdes1) );
-
- assign RAM_CLK = clk_to_mac;
-
- // /////////////////////////////////////////////////////////////////////////
- // VITA Timing
-
- time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
- (.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
- .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int));
-
- // /////////////////////////////////////////////////////////////////////////////////////////
- // Debug Pins
-
- assign debug_clk = 2'b00; // {dsp_clk, clk_to_mac};
- assign debug = 32'd0; // debug_extfifo;
- assign debug_gpio_0 = 32'd0;
- assign debug_gpio_1 = 32'd0;
-
-endmodule // u2_core
--
cgit v1.2.3
From 19073f68c864d13c79251e0e9a7ef14acb917a49 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Thu, 9 Dec 2010 23:44:53 -0800
Subject: Only do udp now, renamed old ports to exp_time_*
---
usrp2/timing/time_64bit.v | 4 +-
usrp2/top/u2_rev3/Makefile | 99 ++++++++++++++++++++++++++++++++++++++++++
usrp2/top/u2_rev3/Makefile.udp | 99 ------------------------------------------
3 files changed, 101 insertions(+), 101 deletions(-)
create mode 100644 usrp2/top/u2_rev3/Makefile
delete mode 100644 usrp2/top/u2_rev3/Makefile.udp
(limited to 'usrp2')
diff --git a/usrp2/timing/time_64bit.v b/usrp2/timing/time_64bit.v
index 1889e73da..d3a0e5b2f 100644
--- a/usrp2/timing/time_64bit.v
+++ b/usrp2/timing/time_64bit.v
@@ -113,13 +113,13 @@ module time_64bit
(.clk(clk),.rst(rst),
.vita_time(vita_time),
.send_sync(send_sync),
- .exp_pps_out(exp_pps_out) );
+ .exp_time_out(exp_time_out) );
time_receiver time_receiver
(.clk(clk),.rst(rst),
.vita_time(vita_time_rcvd),
.sync_rcvd(sync_rcvd),
- .exp_pps_in(exp_pps_in) );
+ .exp_time_in(exp_time_in) );
endmodule // time_64bit
diff --git a/usrp2/top/u2_rev3/Makefile b/usrp2/top/u2_rev3/Makefile
new file mode 100644
index 000000000..05ada2476
--- /dev/null
+++ b/usrp2/top/u2_rev3/Makefile
@@ -0,0 +1,99 @@
+#
+# Copyright 2008 Ettus Research LLC
+#
+
+##################################################
+# Project Setup
+##################################################
+TOP_MODULE = u2_rev3
+BUILD_DIR = $(abspath build)
+
+##################################################
+# Include other makefiles
+##################################################
+
+include ../Makefile.common
+include ../../fifo/Makefile.srcs
+include ../../control_lib/Makefile.srcs
+include ../../sdr_lib/Makefile.srcs
+include ../../serdes/Makefile.srcs
+include ../../simple_gemac/Makefile.srcs
+include ../../timing/Makefile.srcs
+include ../../opencores/Makefile.srcs
+include ../../vrt/Makefile.srcs
+include ../../udp/Makefile.srcs
+include ../../coregen/Makefile.srcs
+include ../../extram/Makefile.srcs
+include ../../extramfifo/Makefile.srcs
+
+
+##################################################
+# Project Properties
+##################################################
+PROJECT_PROPERTIES = \
+family Spartan3 \
+device xc3s2000 \
+package fg456 \
+speed -5 \
+top_level_module_type "HDL" \
+synthesis_tool "XST (VHDL/Verilog)" \
+simulator "ISE Simulator (VHDL/Verilog)" \
+"Preferred Language" "Verilog" \
+"Enable Message Filtering" FALSE \
+"Display Incremental Messages" FALSE
+
+##################################################
+# Sources
+##################################################
+TOP_SRCS = \
+u2_core.v \
+u2_rev3.v \
+u2_rev3.ucf
+
+SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
+$(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
+$(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
+$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
+
+##################################################
+# Process Properties
+##################################################
+SYNTHESIZE_PROPERTIES = \
+"Number of Clock Buffers" 8 \
+"Pack I/O Registers into IOBs" Yes \
+"Optimization Effort" High \
+"Optimize Instantiated Primitives" TRUE \
+"Register Balancing" Yes \
+"Use Clock Enable" Auto \
+"Use Synchronous Reset" Auto \
+"Use Synchronous Set" Auto
+
+TRANSLATE_PROPERTIES = \
+"Macro Search Path" "$(shell pwd)/../../coregen/"
+
+MAP_PROPERTIES = \
+"Allow Logic Optimization Across Hierarchy" TRUE \
+"Map to Input Functions" 4 \
+"Optimization Strategy (Cover Mode)" Speed \
+"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \
+"Perform Timing-Driven Packing and Placement" TRUE \
+"Map Effort Level" High \
+"Extra Effort" Normal \
+"Combinatorial Logic Optimization" TRUE \
+"Register Duplication" TRUE
+
+PLACE_ROUTE_PROPERTIES = \
+"Place & Route Effort Level (Overall)" High
+
+STATIC_TIMING_PROPERTIES = \
+"Number of Paths in Error/Verbose Report" 10 \
+"Report Type" "Error Report"
+
+GEN_PROG_FILE_PROPERTIES = \
+"Configuration Rate" 6 \
+"Create Binary Configuration File" TRUE \
+"Done (Output Events)" 5 \
+"Enable Bitstream Compression" TRUE \
+"Enable Outputs (Output Events)" 6
+
+SIM_MODEL_PROPERTIES = ""
diff --git a/usrp2/top/u2_rev3/Makefile.udp b/usrp2/top/u2_rev3/Makefile.udp
deleted file mode 100644
index 05ada2476..000000000
--- a/usrp2/top/u2_rev3/Makefile.udp
+++ /dev/null
@@ -1,99 +0,0 @@
-#
-# Copyright 2008 Ettus Research LLC
-#
-
-##################################################
-# Project Setup
-##################################################
-TOP_MODULE = u2_rev3
-BUILD_DIR = $(abspath build)
-
-##################################################
-# Include other makefiles
-##################################################
-
-include ../Makefile.common
-include ../../fifo/Makefile.srcs
-include ../../control_lib/Makefile.srcs
-include ../../sdr_lib/Makefile.srcs
-include ../../serdes/Makefile.srcs
-include ../../simple_gemac/Makefile.srcs
-include ../../timing/Makefile.srcs
-include ../../opencores/Makefile.srcs
-include ../../vrt/Makefile.srcs
-include ../../udp/Makefile.srcs
-include ../../coregen/Makefile.srcs
-include ../../extram/Makefile.srcs
-include ../../extramfifo/Makefile.srcs
-
-
-##################################################
-# Project Properties
-##################################################
-PROJECT_PROPERTIES = \
-family Spartan3 \
-device xc3s2000 \
-package fg456 \
-speed -5 \
-top_level_module_type "HDL" \
-synthesis_tool "XST (VHDL/Verilog)" \
-simulator "ISE Simulator (VHDL/Verilog)" \
-"Preferred Language" "Verilog" \
-"Enable Message Filtering" FALSE \
-"Display Incremental Messages" FALSE
-
-##################################################
-# Sources
-##################################################
-TOP_SRCS = \
-u2_core.v \
-u2_rev3.v \
-u2_rev3.ucf
-
-SOURCES = $(abspath $(TOP_SRCS)) $(FIFO_SRCS) \
-$(CONTROL_LIB_SRCS) $(SDR_LIB_SRCS) $(SERDES_SRCS) \
-$(SIMPLE_GEMAC_SRCS) $(TIMING_SRCS) $(OPENCORES_SRCS) \
-$(VRT_SRCS) $(UDP_SRCS) $(COREGEN_SRCS) $(EXTRAM_SRCS)
-
-##################################################
-# Process Properties
-##################################################
-SYNTHESIZE_PROPERTIES = \
-"Number of Clock Buffers" 8 \
-"Pack I/O Registers into IOBs" Yes \
-"Optimization Effort" High \
-"Optimize Instantiated Primitives" TRUE \
-"Register Balancing" Yes \
-"Use Clock Enable" Auto \
-"Use Synchronous Reset" Auto \
-"Use Synchronous Set" Auto
-
-TRANSLATE_PROPERTIES = \
-"Macro Search Path" "$(shell pwd)/../../coregen/"
-
-MAP_PROPERTIES = \
-"Allow Logic Optimization Across Hierarchy" TRUE \
-"Map to Input Functions" 4 \
-"Optimization Strategy (Cover Mode)" Speed \
-"Pack I/O Registers/Latches into IOBs" "For Inputs and Outputs" \
-"Perform Timing-Driven Packing and Placement" TRUE \
-"Map Effort Level" High \
-"Extra Effort" Normal \
-"Combinatorial Logic Optimization" TRUE \
-"Register Duplication" TRUE
-
-PLACE_ROUTE_PROPERTIES = \
-"Place & Route Effort Level (Overall)" High
-
-STATIC_TIMING_PROPERTIES = \
-"Number of Paths in Error/Verbose Report" 10 \
-"Report Type" "Error Report"
-
-GEN_PROG_FILE_PROPERTIES = \
-"Configuration Rate" 6 \
-"Create Binary Configuration File" TRUE \
-"Done (Output Events)" 5 \
-"Enable Bitstream Compression" TRUE \
-"Enable Outputs (Output Events)" 6
-
-SIM_MODEL_PROPERTIES = ""
--
cgit v1.2.3
From 003df1ee96234f92c17f6c5f19c3c7e0a72490e9 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Fri, 10 Dec 2010 00:26:31 -0800
Subject: slave side can now sync
---
usrp2/timing/time_64bit.v | 38 +++++++++++++++++++++++++++-----------
usrp2/timing/time_receiver.v | 8 ++++++--
2 files changed, 33 insertions(+), 13 deletions(-)
(limited to 'usrp2')
diff --git a/usrp2/timing/time_64bit.v b/usrp2/timing/time_64bit.v
index d3a0e5b2f..a03f437e8 100644
--- a/usrp2/timing/time_64bit.v
+++ b/usrp2/timing/time_64bit.v
@@ -15,16 +15,28 @@ module time_64bit
localparam PPS_POLSRC = 2;
localparam PPS_IMM = 3;
localparam TPS = 4;
+ localparam MIMO_SYNC = 5;
reg [31:0] seconds, ticks;
wire end_of_second;
assign vita_time = {seconds,ticks};
+ wire [63:0] vita_time_rcvd;
wire [31:0] next_ticks_preset, next_seconds_preset;
wire [31:0] ticks_per_sec_reg;
wire set_on_pps_trig;
reg set_on_next_pps;
wire pps_polarity, pps_source, set_imm;
+ reg [1:0] pps_del;
+ reg pps_reg_p, pps_reg_n, pps_reg;
+ wire pps_edge;
+
+ reg [15:0] sync_counter;
+ wire sync_rcvd;
+ wire [31:0] mimo_secs, mimo_ticks;
+ wire mimo_sync_now;
+ wire mimo_sync;
+ wire [7:0] sync_delay;
setting_reg #(.my_addr(BASE+NEXT_TICKS)) sr_next_ticks
(.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
@@ -46,10 +58,10 @@ module time_64bit
(.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
.in(set_data),.out(ticks_per_sec_reg),.changed());
- reg [1:0] pps_del;
- reg pps_reg_p, pps_reg_n, pps_reg;
- wire pps_edge;
-
+ setting_reg #(.my_addr(BASE+MIMO_SYNC), .at_reset(0), .width(9)) sr_mimosync
+ (.clk(clk),.rst(rst),.strobe(set_stb),.addr(set_addr),
+ .in(set_data),.out({mimo_sync,sync_delay}),.changed());
+
always @(posedge clk) pps_reg_p <= pps;
always @(negedge clk) pps_reg_n <= pps;
always @* pps_reg <= pps_polarity ? pps_reg_p : pps_reg_n;
@@ -83,6 +95,11 @@ module time_64bit
seconds <= next_seconds_preset;
ticks <= next_ticks_preset;
end
+ else if(mimo_sync_now)
+ begin
+ seconds <= mimo_secs;
+ ticks <= mimo_ticks;
+ end
else if(ticks_plus_one == ticks_per_sec_reg)
begin
seconds <= seconds + 1;
@@ -93,11 +110,9 @@ module time_64bit
assign pps_int = pps_edge;
- localparam SYNC_RATE = 59999; // Send every 600uS
- reg [15:0] sync_counter;
- wire send_sync = (sync_counter == SYNC_RATE);
- wire sync_rcvd;
-
+ // MIMO Connector Time Sync
+ wire send_sync = (sync_counter == 59999); // X % 10 = 9
+
always @(posedge clk)
if(rst)
sync_counter <= 0;
@@ -107,8 +122,6 @@ module time_64bit
else
sync_counter <= sync_counter + 1;
- // must be greater than 1000, 1 less than a multiple of 10;
-
time_sender time_sender
(.clk(clk),.rst(rst),
.vita_time(vita_time),
@@ -121,5 +134,8 @@ module time_64bit
.sync_rcvd(sync_rcvd),
.exp_time_in(exp_time_in) );
+ assign mimo_secs = vita_time_rcvd[63:32];
+ assign mimo_ticks = vita_time_rcvd[31:0] + {16'd0,sync_delay};
+ assign mimo_sync_now = mimo_sync & sync_rcvd & (mimo_ticks <= TICKS_PER_SEC);
endmodule // time_64bit
diff --git a/usrp2/timing/time_receiver.v b/usrp2/timing/time_receiver.v
index 71f0ace90..fd8651d29 100644
--- a/usrp2/timing/time_receiver.v
+++ b/usrp2/timing/time_receiver.v
@@ -2,7 +2,7 @@
module time_receiver
(input clk, input rst,
output reg [63:0] vita_time,
- output sync_rcvd,
+ output reg sync_rcvd,
input exp_time_in);
wire code_err, disp_err, dispout, complete_word;
@@ -121,6 +121,10 @@ module time_receiver
state <= STATE_IDLE;
endcase // case(state)
- assign sync_rcvd = (complete_word & (state == STATE_TAIL) & (dataout_reg[8:0] == TAIL));
+ always @(posedge clk)
+ if(rst)
+ sync_rcvd <= 0;
+ else
+ sync_rcvd <= (complete_word & (state == STATE_TAIL) & (dataout_reg[8:0] == TAIL));
endmodule // time_sender
--
cgit v1.2.3
From c97440838aa740fc335c59914f6dfd6f492b69f8 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Fri, 10 Dec 2010 10:49:59 -0800
Subject: time sync on usrp2 as well, added debug pins to time sync.
---
usrp2/timing/time_64bit.v | 6 +++++-
usrp2/top/u2_rev3/u2_core.v | 6 +++++-
2 files changed, 10 insertions(+), 2 deletions(-)
(limited to 'usrp2')
diff --git a/usrp2/timing/time_64bit.v b/usrp2/timing/time_64bit.v
index a03f437e8..33eb2b25a 100644
--- a/usrp2/timing/time_64bit.v
+++ b/usrp2/timing/time_64bit.v
@@ -7,7 +7,8 @@ module time_64bit
input set_stb, input [7:0] set_addr, input [31:0] set_data,
input pps,
output [63:0] vita_time, output pps_int,
- input exp_time_in, output exp_time_out
+ input exp_time_in, output exp_time_out,
+ output [31:0] debug
);
localparam NEXT_SECS = 0;
@@ -137,5 +138,8 @@ module time_64bit
assign mimo_secs = vita_time_rcvd[63:32];
assign mimo_ticks = vita_time_rcvd[31:0] + {16'd0,sync_delay};
assign mimo_sync_now = mimo_sync & sync_rcvd & (mimo_ticks <= TICKS_PER_SEC);
+
+ assign debug = { { 24'b0} ,
+ { 2'b0, exp_time_in, exp_time_out, mimo_sync, mimo_sync_now, sync_rcvd, send_sync} };
endmodule // time_64bit
diff --git a/usrp2/top/u2_rev3/u2_core.v b/usrp2/top/u2_rev3/u2_core.v
index c2d473650..30b47b818 100644
--- a/usrp2/top/u2_rev3/u2_core.v
+++ b/usrp2/top/u2_rev3/u2_core.v
@@ -720,9 +720,13 @@ module u2_core
// /////////////////////////////////////////////////////////////////////////
// VITA Timing
+ wire [31:0] debug_sync;
+
time_64bit #(.TICKS_PER_SEC(32'd100000000),.BASE(SR_TIME64)) time_64bit
(.clk(dsp_clk), .rst(dsp_rst), .set_stb(set_stb_dsp), .set_addr(set_addr_dsp), .set_data(set_data_dsp),
- .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int));
+ .pps(pps_in), .vita_time(vita_time), .pps_int(pps_int),
+ .exp_time_in(exp_time_in), .exp_time_out(exp_time_out),
+ .debug(debug_sync));
// /////////////////////////////////////////////////////////////////////////////////////////
// Debug Pins
--
cgit v1.2.3