From 91636cbac2b3edfba45321f1050d0b90b34ab696 Mon Sep 17 00:00:00 2001
From: Johnathan Corgan <jcorgan@corganenterprises.com>
Date: Mon, 31 Aug 2009 12:08:30 -0700
Subject: Merged SVN matt/new_eth r10782:11633 into new_eth

* svn diff http://gnuradio.org/svn/branches/developers/matt/new_eth
  -r10782:11633

* Patch applied with no conflicts or fuzz.
---
 control_lib/buffer_int.v | 251 -----------------------------------------------
 1 file changed, 251 deletions(-)

(limited to 'control_lib/buffer_int.v')

diff --git a/control_lib/buffer_int.v b/control_lib/buffer_int.v
index c33f2779d..e69de29bb 100644
--- a/control_lib/buffer_int.v
+++ b/control_lib/buffer_int.v
@@ -1,251 +0,0 @@
-
-// FIFO Interface to the 2K buffer RAMs
-// Read port is read-acknowledge
-// FIXME do we want to be able to interleave reads and writes?
-
-module buffer_int
-  #(parameter BUFF_NUM = 0)
-    (// Control Interface
-     input clk,
-     input rst,
-     input [31:0] ctrl_word,
-     input go,
-     output done,
-     output error,
-     output idle,
-     
-     // Buffer Interface
-     output en_o,
-     output we_o,
-     output reg [8:0] addr_o,
-     output [31:0] dat_to_buf,
-     input [31:0] dat_from_buf,
-     
-     // Write FIFO Interface
-     input [31:0] wr_dat_i,
-     input wr_write_i,
-     input wr_done_i,
-     input wr_error_i,
-     output reg wr_ready_o,
-     output reg wr_full_o,
-     
-     // Read FIFO Interface
-     output [31:0] rd_dat_o,
-     input rd_read_i,
-     input rd_done_i,
-     input rd_error_i,
-     output reg rd_sop_o,
-     output reg rd_eop_o
-     );
-   
-   reg [31:0] ctrl_reg;
-   reg 	      go_reg;
-   
-   always @(posedge clk)
-     go_reg <= go;
-   
-   always @(posedge clk)
-     if(rst)
-       ctrl_reg <= 0;
-     else
-       if(go & (ctrl_word[31:28] == BUFF_NUM))
-	 ctrl_reg <= ctrl_word;
-   
-   wire [8:0] firstline = ctrl_reg[8:0];
-   wire [8:0] lastline = ctrl_reg[17:9];
-   wire [3:0] step = ctrl_reg[21:18];
-   wire       read = ctrl_reg[22];
-   wire       write = ctrl_reg[23];
-   wire       clear = ctrl_reg[24];
-   //wire [2:0] port = ctrl_reg[27:25];  // Ignored in this block
-   //wire [3:0] buff_num = ctrl_reg[31:28];  // Ignored here ?
-   
-   assign     dat_to_buf = wr_dat_i;
-   assign     rd_dat_o = dat_from_buf;
-   
-   localparam IDLE = 3'd0;
-   localparam PRE_READ = 3'd1;
-   localparam READING = 3'd2;
-   localparam WRITING = 3'd3;
-   localparam ERROR = 3'd4;
-   localparam DONE = 3'd5;
-   
-   reg [2:0]  state;
-   
-   always @(posedge clk)
-     if(rst)
-       begin
-	  state <= IDLE;
-	  rd_sop_o <= 0;
-	  rd_eop_o <= 0;
-	  wr_ready_o <= 0;
-	  wr_full_o <= 0;
-       end
-     else
-       if(clear)
-	 begin
-	    state <= IDLE;
-	    rd_sop_o <= 0;
-	    rd_eop_o <= 0;
-	    wr_ready_o <= 0;
-	    wr_full_o <= 0;
-	 end
-       else 
-	 case(state)
-	   IDLE :
-	     if(go_reg & read)
-	       begin
-		  addr_o <= firstline;
-		  state <= PRE_READ;
-	       end
-	     else if(go_reg & write)
-	       begin
-		  addr_o <= firstline;
-		  state <= WRITING;
-		  wr_ready_o <= 1;
-	       end
-	   
-	   PRE_READ :
-	     begin
-		state <= READING;
-		addr_o <= addr_o + 1;
-		rd_sop_o <= 1;
-	     end
-	   
-	   READING :
-	     if(rd_error_i)
-	       state <= ERROR;
-	     else if(rd_done_i)
-	       state <= DONE;
-	     else if(rd_read_i)
-	       begin
-		  rd_sop_o <= 0;
-		  addr_o <= addr_o + 1;
-		  if(addr_o == lastline)
-		    rd_eop_o <= 1;
-		  else
-		    rd_eop_o <= 0;
-		  if(rd_eop_o)
-		    state <= DONE;
-	       end
-	   
-	   WRITING :
-	     begin
-		if(wr_write_i)
-		  addr_o <= addr_o + 1;  // This was the timing problem, so now it doesn't depend on wr_error_i
-		if(wr_error_i)
-		  begin
-		     state <= ERROR;
-		     wr_ready_o <= 0;
-		  end
-		else
-		  begin
-		     if(wr_write_i)
-		       begin
-			  wr_ready_o <= 0;
-			  if(addr_o == (lastline-1))
-			    wr_full_o <= 1;
-			  if(addr_o == lastline)
-			    state <= DONE;
-		       end
-		     if(wr_done_i)
-		       begin
-			  state <= DONE;
-			  wr_ready_o <= 0;
-		       end
-		  end // else: !if(wr_error_i)
-	     end // case: WRITING
-
-	   DONE :
-	     begin
-		rd_eop_o <= 0;
-		rd_sop_o <= 0;
-		wr_ready_o <= 0;
-		wr_full_o <= 0;
-	     end
-	   
-	 endcase // case(state)
-   
-   // FIXME ignores step for now
-
-   assign     we_o = (state == WRITING) && wr_write_i;  // FIXME potential critical path
-                   // IF this is a timing problem, we could always write when in this state
-   assign     en_o = ~((state==READING)& ~rd_read_i);   // FIXME potential critical path
-   
-   assign     done = (state == DONE);
-   assign     error = (state == ERROR);
-   assign     idle = (state == IDLE);
-endmodule // buffer_int
-
-
-
-// These are 2 other ways for doing the WRITING state, both work.  First one is faster, but confusing
-/*
-	     begin
-		// Gen 4 values -- state, wr_ready_o, addr_o, wr_full_o
-		if(~wr_error_i & wr_write_i & (addr_o == (lastline-1)))
-		  wr_full_o <= 1;
-		if(wr_error_i | wr_write_i | wr_done_i)
-		  wr_ready_o <= 0;
-		if(wr_error_i)
-		  state <= ERROR;
-		else if(wr_done_i | (wr_write_i & (addr_o == lastline)))
-		  state <= DONE;
-		// This one was the timing problem...  now we increment addr_o even if there is an error
-		if(wr_write_i)
-		  addr_o <= addr_o + 1;
-	     end // case: WRITING
-*/	   
-		
-/*      begin
-		if(wr_error_i)
-		  begin
-		     state <= ERROR;
-		     wr_ready_o <= 0;
-		  end
-		else
-		  begin
-		     if(wr_write_i)
-		       begin
-			  wr_ready_o <= 0;
-			  addr_o <= addr_o + 1;
-			  if(addr_o == (lastline-1))
-			    wr_full_o <= 1;
-			  if(addr_o == lastline)
-			    state <= DONE;
-		       end
-		     if(wr_done_i)
-		       begin
-			  state <= DONE;
-			  wr_ready_o <= 0;
-		       end
-		  end // else: !if(wr_error_i)
-	     end // case: WRITING
-*/
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-// Unused old code
-   //assign     rd_empty_o = (state != READING); // && (state != PRE_READ);
-   //assign     rd_empty_o = rd_empty_reg;         // timing fix?
-   //assign     rd_ready_o = (state == READING);
-   //assign     rd_ready_o = ~rd_empty_reg;        // timing fix?
-   
-   //wire       rd_en = (state == PRE_READ) || ((state == READING) && rd_read_i);
-   //wire       wr_en = (state == WRITING) && wr_write_i;  // IF this is a timing problem, we could always enable when in this state
-   //assign     en_o = rd_en | wr_en;   
-   
-   // assign     wr_full_o = (state != WRITING);
-   // assign     wr_ready_o = (state == WRITING);
-   
-- 
cgit v1.2.3


From 29fa1be3dc307d6d9be0fc3a004213eea50e6071 Mon Sep 17 00:00:00 2001
From: Matt Ettus <matt@ettus.com>
Date: Wed, 2 Sep 2009 16:46:06 -0700
Subject: Removed these files completely, they were for the old style of fifos

---
 control_lib/buffer_int.v     |   0
 control_lib/buffer_int_tb.v  | 447 -------------------------------------------
 control_lib/buffer_pool.v    |   0
 control_lib/buffer_pool_tb.v |  50 -----
 4 files changed, 497 deletions(-)
 delete mode 100644 control_lib/buffer_int.v
 delete mode 100644 control_lib/buffer_int_tb.v
 delete mode 100644 control_lib/buffer_pool.v
 delete mode 100644 control_lib/buffer_pool_tb.v

(limited to 'control_lib/buffer_int.v')

diff --git a/control_lib/buffer_int.v b/control_lib/buffer_int.v
deleted file mode 100644
index e69de29bb..000000000
diff --git a/control_lib/buffer_int_tb.v b/control_lib/buffer_int_tb.v
deleted file mode 100644
index 4fb5c6710..000000000
--- a/control_lib/buffer_int_tb.v
+++ /dev/null
@@ -1,447 +0,0 @@
-
-module buffer_int_tb ();
-
-   reg clk = 0;
-   reg rst = 1;
-
-   initial #100 rst = 0;
-   always #5 clk = ~clk;
-
-   wire en, we;
-   wire [8:0] addr;
-   wire [31:0] fifo2buf, buf2fifo;
-   
-   wire [31:0] rd_dat_o;
-   wire        rd_sop_o, rd_eop_o;
-   reg 	       rd_done_i = 0, rd_error_i = 0, rd_read_i = 0;
-   
-   reg [31:0]  wr_dat_i = 0;
-   reg 	       wr_write_i=0, wr_done_i = 0, wr_error_i = 0;
-   wire        wr_ready_o, wr_full_o;
-   
-   reg 	       clear = 0, write = 0, read = 0;
-   reg [8:0]   firstline = 0, lastline = 0;
-   wire [3:0]  step = 1;
-   wire [31:0] ctrl_word = {4'b0,3'b0,clear,write,read,step,lastline,firstline};
-   reg 	       go = 0;
-   wire        done, error;
-   
-   buffer_int buffer_int
-     (.clk(clk),.rst(rst),
-      .ctrl_word(ctrl_word),.go(go),
-      .done(done),.error(error),
-      
-      // Buffer Interface
-      .en_o(en),.we_o(we),.addr_o(addr),
-      .dat_to_buf(fifo2buf),.dat_from_buf(buf2fifo),
-
-      // Write FIFO Interface
-      .wr_dat_i(wr_dat_i), .wr_write_i(wr_write_i), .wr_done_i(wr_done_i), .wr_error_i(wr_error_i), 
-      .wr_ready_o(wr_ready_o), .wr_full_o(wr_full_o),
-   
-      // Read FIFO Interface
-      .rd_dat_o(rd_dat_o), .rd_read_i(rd_read_i), .rd_done_i(rd_done_i), .rd_error_i(rd_error_i),
-      .rd_sop_o(rd_sop_o), .rd_eop_o(rd_eop_o)
-      );
-   
-   reg 	       ram_en = 0, ram_we = 0;
-   reg [8:0]   ram_addr = 0;
-   reg [31:0]  ram_data = 0;
-   
-   ram_2port #(.DWIDTH(32),.AWIDTH(9)) ram_2port
-     (.clka(clk), .ena(ram_en), .wea(ram_we), .addra(ram_addr), .dia(ram_data), .doa(),
-      .clkb(clk), .enb(en), .web(we), .addrb(addr), .dib(fifo2buf), .dob(buf2fifo) );
-   
-   initial
-     begin
-	@(negedge rst);
-	@(posedge clk);
-	FillRAM;
-
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing full read, no wait states.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(6,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing full read, 2 wait states.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(6,2);
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing full read, done ON the last.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(5,2);
-	rd_done_i <= 1;
-	ReadALine;
-	rd_done_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing partial read, 0 wait states, then nothing after last.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(3,0);
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing partial read, 0 wait states, then done after last.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(3,0);
-	rd_done_i <= 1;
-	@(posedge clk);
-	rd_done_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing partial read, 0 wait states, then done at same time as last.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(2,0);
-	rd_done_i <= 1;
-	ReadALine;
-	rd_done_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing partial read, 3 wait states, then error at same time as last.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(2,3);
-	rd_error_i <= 1;
-	ReadALine;
-	rd_error_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferRead(5,10);
-	$display("Testing Reading too much, 3 wait states.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(9,3);
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferRead(500,511);
-	$display("Testing full read, to the end of the buffer.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(12,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(0,511);
-	$display("Testing full read, start to end of the buffer.");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(512,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(505,3);
-	$display("Testing full read, wraparound");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(11,0);
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferWrite(10,15);
-	$display("Testing Full Write, no wait states");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(6,0,72);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(18,23);
-	$display("Testing Full Write, 1 wait states");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(6,0,101);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(27,40);
-	$display("Testing Partial Write, 0 wait states");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(6,0,201);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(35,200);
-	$display("Testing Partial Write, 0 wait states, then done");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(6,0,301);
-	wr_done_i <= 1;
-	@(posedge clk);
-	wr_done_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-
-	ResetBuffer;
-	SetBufferWrite(45,200);
-	$display("Testing Partial Write, 0 wait states, then done and write simultaneously");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(6,0,301);
-	wr_done_i <= 1;
-	WriteALine(400);
-	wr_done_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(55,200);
-	$display("Testing Partial Write, 0 wait states, then error");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(6,0,501);
-	wr_error_i <= 1;
-	@(posedge clk);
-	wr_error_i <= 0;
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(0,82);
-	$display("Testing read after all the writes");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(83,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(508,4);
-	$display("Testing wraparound write");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(9,0,601);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(506,10);
-	$display("Reading wraparound write");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(17,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(0,511);
-	$display("Testing Whole Buffer write");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(512,0,1000);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(0,511);
-	$display("Reading Whole Buffer write");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(512,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(5,10);
-	$display("Testing Write Too Many");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(12,0,2000);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(0,15);
-	$display("Reading back Write Too Many");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(16,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferWrite(15,20);
-	$display("Testing Write One Less Than Full");
-	while(!wr_ready_o)
-	  @(posedge clk);
-	WriteLines(5,0,2000);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	SetBufferRead(13,22);
-	$display("Reading back Write One Less Than Full");
-	while(!rd_sop_o)
-	  @(posedge clk);
-	ReadLines(10,0);
-	repeat (10)
-	  @(posedge clk);
-	
-	ResetBuffer;
-	repeat(100)
-	  @(posedge clk);
-	$finish;
-     end
-   
-   always @(posedge clk)
-     if(rd_read_i == 1'd1)
-       $display("READ Buffer %d, rd_sop_o %d, rd_eop_o %d", rd_dat_o, rd_sop_o, rd_eop_o);
-
-   always @(posedge clk)
-     if(wr_write_i == 1'd1)
-       $display("WRITE Buffer %d,  wr_ready_o %d, wr_full_o %d", wr_dat_i, wr_ready_o, wr_full_o);
-	   
-   initial begin
-      $dumpfile("buffer_int_tb.vcd");
-      $dumpvars(0,buffer_int_tb);
-   end
-
-   task FillRAM;
-      begin
-	 ram_addr <= 0;
-	 ram_data <= 0;
-	 @(posedge clk);
-	 ram_en <= 1;
-	 ram_we <= 1;
-	 @(posedge clk);
-	 repeat (511)
-	   begin
-	      ram_addr <= ram_addr + 1;
-	      ram_data <= ram_data + 1;
-	      ram_en <= 1;
-	      ram_we <= 1;
-	      @(posedge clk);
-	   end
-	 ram_en <= 0;
-	 ram_we <= 0;
-	 @(posedge clk);
-	 $display("Filled the RAM");
-      end
-   endtask // FillRAM
-
-   task ResetBuffer;
-      begin
-	 clear <= 1; read <= 0; write <= 0;
-	 go <= 1;
-	 @(posedge clk);
-	 go <= 0;
-	 @(posedge clk);
-	 $display("Buffer Reset");
-      end
-   endtask // ClearBuffer
-   
-   task SetBufferWrite;
-      input [8:0] start;
-      input [8:0] stop;
-      begin
-	 clear <= 0; read <= 0; write <= 1;
-	 firstline <= start;
-	 lastline <= stop;
-	 go <= 1;
-	 @(posedge clk);
-	 go <= 0;
-	 @(posedge clk);
-	 $display("Buffer Set for Write");
-      end
-   endtask // SetBufferWrite
-   
-   task SetBufferRead;
-      input [8:0] start;
-      input [8:0] stop;
-      begin
-	 clear <= 0; read <= 1; write <= 0;
-	 firstline <= start;
-	 lastline <= stop;
-	 go <= 1;
-	 @(posedge clk);
-	 go <= 0;
-	 @(posedge clk);
-	 $display("Buffer Set for Read");
-      end
-   endtask // SetBufferRead
-
-   task ReadALine;
-      begin
-	 #1 rd_read_i <= 1;
-	 @(posedge clk);
-	 rd_read_i <= 0;
-      end
-   endtask // ReadALine
-
-   task ReadLines;
-      input [9:0] lines;
-      input [7:0] wait_states;
-      begin
-	 $display("Read Lines: Number %d, Wait States %d",lines,wait_states);
-	 repeat (lines)
-	   begin
-	      ReadALine;
-	      repeat (wait_states)
-		@(posedge clk);
-	   end
-      end
-   endtask // ReadLines
-   
-   task WriteALine;
-      input [31:0] value;
-      begin
-	 #1 wr_write_i <= 1;
-	 wr_dat_i <= value;
-	 @(posedge clk);
-	 wr_write_i <= 0;
-      end
-   endtask // WriteALine
-   
-   task WriteLines;
-      input [9:0] lines;
-      input [7:0] wait_states;
-      input [31:0] value;
-      begin
-	 $display("Write Lines: Number %d, Wait States %d",lines,wait_states);
-	 repeat(lines)
-	   begin
-	      value <= value + 1;
-	      WriteALine(value);
-	      repeat(wait_states)
-		@(posedge clk);
-	   end
-      end
-   endtask // WriteLines
-   
-endmodule // buffer_int_tb
diff --git a/control_lib/buffer_pool.v b/control_lib/buffer_pool.v
deleted file mode 100644
index e69de29bb..000000000
diff --git a/control_lib/buffer_pool_tb.v b/control_lib/buffer_pool_tb.v
deleted file mode 100644
index 16741438e..000000000
--- a/control_lib/buffer_pool_tb.v
+++ /dev/null
@@ -1,50 +0,0 @@
-
-module buffer_pool_tb();
-   
-   wire wb_clk_i;
-   wire wb_rst_i;
-   wire wb_we_i;
-   wire wb_stb_i;
-   wire [15:0] wb_adr_i;
-   wire [31:0] wb_dat_i;   
-   wire [31:0] wb_dat_o;
-   wire wb_ack_o;
-   wire wb_err_o;
-   wire wb_rty_o;
-
-   wire stream_clk, stream_rst;
-
-   wire set_stb;
-   wire [7:0] set_addr;
-   wire [31:0] set_data;
-
-   wire [31:0] wr0_dat_i;
-   buffer_pool dut
-     (.wb_clk_i(wb_clk_i),
-      .wb_rst_i(wb_rst_i),
-      .wb_we_i(wb_we_i),
-      .wb_stb_i(wb_stb_i),
-      .wb_adr_i(wb_adr_i),
-      .wb_dat_i(wb_dat_i),   
-      .wb_dat_o(wb_dat_o),
-      .wb_ack_o(wb_ack_o),
-      .wb_err_o(wb_err_o),
-      .wb_rty_o(wb_rty_o),
-      
-      .stream_clk(stream_clk),
-      .stream_rst(stream_rst),
-      
-      .set_stb(set_stb),.set_addr(set_addr),.set_data(set_data),
-      
-      .wr0_dat_i(wr0_dat_i), .wr0_write_i(), .wr0_done_i(), .wr0_error_i(), .wr0_ready_o(), .wr0_full_o(),
-      .wr1_dat_i(), .wr1_write_i(), .wr1_done_i(), .wr1_error_i(), .wr1_ready_o(), .wr1_full_o(),
-      .wr2_dat_i(), .wr2_write_i(), .wr2_done_i(), .wr2_error_i(), .wr2_ready_o(), .wr2_full_o(),
-      .wr3_dat_i(), .wr3_write_i(), .wr3_done_i(), .wr3_error_i(), .wr3_ready_o(), .wr3_full_o(),
-      
-      .rd0_dat_o(), .rd0_read_i(), .rd0_done_i(), .rd0_error_i(), .rd0_ready_o(), .rd0_empty_o(),
-      .rd1_dat_o(), .rd1_read_i(), .rd1_done_i(), .rd1_error_i(), .rd1_ready_o(), .rd1_empty_o(),
-      .rd2_dat_o(), .rd2_read_i(), .rd2_done_i(), .rd2_error_i(), .rd2_ready_o(), .rd2_empty_o(),
-      .rd3_dat_o(), .rd3_read_i(), .rd3_done_i(), .rd3_error_i(), .rd3_ready_o(), .rd3_empty_o()
-      );
-   
-endmodule // buffer_pool_tb
-- 
cgit v1.2.3