summaryrefslogtreecommitdiffstats
path: root/usrp2/top
Commit message (Collapse)AuthorAgeFilesLines
* 1) u2p has added a new signal from the SRAM to the pinout, RAM_ZZIan Buckley2010-11-112-2/+5
| | | | | | | | | | | | | | | which allows the SRAM to be placed in a sleep mode. This pin was erroniously pulled high at the top level rendering the SRAM unusable. 2) Added declaration for extramfifo debug bus which had got deleted at some point in the past 3) Created a debug bundle of signals from extsramfifo to help diagnose problem 1) 4) u2p Rev1 PCB ommits control of any of the SRAM chip selects. Made a code change so that control logic does not rely on the presence of this pin and ensuring that the SRAM is always placed in READ mode in any idle cycles.
* Defaulted all SRAM pins to LVCMOS25 8mA FASTIan Buckley2010-11-111-67/+67
|
* Placed 2nd DCM into `ifdef DCM_FOR_RAMCLK which is dissabled by defaultIan Buckley2010-11-112-7/+23
| | | | | Derived RAMCLK from 270degree offset of principle core DCM giving theoretical 2.5nS timing advance on RAM_CLK relative to RAM_* signals.
* Added external RAM FIFO to u2plus.Ian Buckley2010-11-114-7/+123
| | | | | | | | | | Added code branch to ext_fifo.v using generate that instantiates different input and out fifo's and touched nobl_fifo code so that it works at 18 and 36bit widths. Added 2nd DCM to top level to generate off chip RAMCLK. Added explicit I/O instances to top level for tristate drivers and changed signals to core as needed. Creted new FIFO's in core gen to replace much larger FIFO's used on u2rev3
* revert unneeded changes and incorrect commentsMatt Ettus2010-11-111-32/+32
|
* reconnect GPIOs, remove debug pins, meets timing nowMatt Ettus2010-11-111-5/+3
|
* Modified phase shift of DCM1 to -64 which is intended to give more timing ↵Ian Buckley2010-11-111-1/+1
| | | | | | | margin on reads from the SRAM at the expense of Writes to the SRAM. Tested to be at least as stable as a phase shift of 12 and beter looking timing on the logic analyzer. Signals driven by the FPGA are observed changing on the SRAM pins about 4 nS after the rising edge of the RAM clock.
* Enabled phase offset adjustment on DCM_INST1 which drives the external Fast ↵Ian Buckley2010-11-111-12/+12
| | | | | | | | SRAM clock. Set phase shift to -12 after experimentation using logic analyzer to see results. This value gives near optimum 1.5nS setup times on the source sync signals FPGA -> SRAM under lab conditions.
* Added to DCM's and some BUFG's to align the internal 125MHz clock edge with ↵Ian Buckley2010-11-114-5/+100
| | | | | | | its presentation externally at the NoBL SRAM. Since we don't have a board level trace to use to estimate clock propigation delay we just loop through the I/O on the FPGA. This hasn't been verified as working on a USRP2 yet.
* hangedddddddextrnal fifo size to use full NoBL SRAMianb2010-11-111-1/+1
|
* Corrected extfifo code so that all registers that are on SRAM signals are ↵ianb2010-11-112-37/+42
| | | | | | | | packed into IOBs Explcit drives and skews added to GPIO pins Corrected minor error in FIFO logic that showed data avail internally incorrectly
* Added a bunch of debug signals.Ian Buckley2010-11-111-4/+5
|
* Regenerated FIFO with lower trigger level for almost full flag to reflect ↵Ian Buckley2010-11-111-1/+2
| | | | | | | | | | | | | logic removed from nobl_fifo. Improved ext_fifo_tb further, try to simulate more combinations of decomation rates and packet arrival patterns. Strip out the logic in nobl_fifo that made it look like a Xilinx fall-through FIFO...it is now very simple logic but a propriatory interface that exposes the high inetrnal latency of reads. Allow the USED size of the external FIFO to be parameterized from the core level. Currently set at only 256 Corrected a bug in vita_tx_deframer.v that can write to a FIFO when its full causing illegal state. Made further edits that are currently commented becuase simulation indicates they cause problems, however suspect a further bug is in this code.
* External FIFO tested in simulation and on USRP2 from decimation 64->8 with ↵Ian Buckley2010-11-115-142/+201
| | | | | | | | current head UHD code. Apparently operation is "flawless" but more regression and corner case regression could and should be done. Tristate drivers have been added at the top level of the hierarchy for the SRAM databus as is considered good practice for both Xilinx and ASIC design flows and so both top level and core fils have been touched.
* Merge branch 'u1e' into merge_u1eMatt Ettus2010-11-1019-0/+1381
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * u1e: (130 commits) invert led signals because they are active low duh allow for CS to rise before, at the same time, or after OE better debug pins watch the ethernet chip select on our debug bus fix timing issue on DAC outputs with rev 2. This puts the whole system on a 90 degree phase shift send all gpmc signals to mictor updated pins to match rev2, removed dip switch, etc. seems to compile ok. pins are different on rev2 fixed makefile to compile with our new system add register to tell host about compatibility level and which image we are using move declaration to make loopback compile no need for protocol headers since we're not doing ethernet match the signal names in this design debug pins cleanup properly integrate the new tx chain catch up with tx_policy attach run_tx and run_rx to leds connect atr delay the q channel to make the channels line up on the AD9862 ... Conflicts: usrp2/control_lib/Makefile.srcs
| * invert led signals because they are active lowMatt Ettus2010-11-091-1/+1
| |
| * duhMatt Ettus2010-11-041-1/+1
| |
| * better debug pinsMatt Ettus2010-09-232-7/+11
| |
| * watch the ethernet chip select on our debug busMatt Ettus2010-09-233-6/+8
| |
| * fix timing issue on DAC outputs with rev 2. This puts the whole system on a ↵Matt Ettus2010-09-212-50/+25
| | | | | | | | 90 degree phase shift
| * send all gpmc signals to mictorMatt Ettus2010-09-164-0/+201
| |
| * updated pins to match rev2, removed dip switch, etc. seems to compile ok.Matt Ettus2010-09-093-137/+130
| |
| * pins are different on rev2Matt Ettus2010-09-091-264/+4
| |
| * fixed makefile to compile with our new systemMatt Ettus2010-09-071-44/+36
| |
| * add register to tell host about compatibility level and which image we are usingMatt Ettus2010-08-301-5/+14
| |
| * move declaration to make loopback compileMatt Ettus2010-08-271-1/+2
| |
| * Merge branch 'tx_policy' into u1eMatt Ettus2010-08-252-7/+10
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * tx_policy: (21 commits) clean up DAC inversion and swapping to match schematics Clean up iq swapping on RX. It is now swapped in the top level. widened muxes to 4 bits to match tx side and handle more ADCs in future rx error context packets should not be marked as errors in the fifo added compat number to usrp2 readback mux makefile dependency fix for second expansion provide a way to get out of the error state without processor intervention sequence number reset upon programming streamid attempt at avoiding infinite error messages implemented "next packet" and "next burst" policies sequence errors can happen on start of burst as well. more informative error codes cleaner error handling introduce new error types test mux and gen_context_pkt this is an output file, it shouldn't be checked in insert protocol engine flags when requested move the streamid so it isn't at the same address as clear_state connect the demux fix a typo tx error packets now muxed into the ethernet stream back to the host ... Conflicts: usrp2/top/u2_rev3/u2_core_udp.v
| * | no need for protocol headers since we're not doing ethernetMatt Ettus2010-08-241-1/+1
| | |
| * | match the signal names in this designMatt Ettus2010-08-231-3/+3
| | |
| * | debug pins cleanupMatt Ettus2010-08-231-3/+3
| | |
| * | properly integrate the new tx chainMatt Ettus2010-08-191-31/+27
| | |
| * | catch up with tx_policyMatt Ettus2010-08-192-30/+28
| | |
| * | attach run_tx and run_rx to ledsMatt Ettus2010-08-171-1/+1
| | |
| * | connect atrMatt Ettus2010-08-171-1/+1
| | |
| * | delay the q channel to make the channels line up on the AD9862Matt Ettus2010-08-171-1/+6
| | |
| * | this is necessary for some reasonMatt Ettus2010-08-131-1/+2
| | |
| * | connect the setting reg to the real clock and resetMatt Ettus2010-08-111-1/+1
| | |
| * | enlarge loopback fifoMatt Ettus2010-08-101-4/+1
| | |
| * | Merge branch 'ise12' into u1eMatt Ettus2010-07-192-37/+36
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * ise12: move declaration ahead of use put run_tx and run_rx on the displayed LEDs remove warnings add mux and demux to build mux multiple fifo streams into one. Allows priority or round robin split fifo into 2 streams based on first line in each packet precompute udp checksums barely fails timing on gigE/10 and gigE/12, larger fail on udp/10, but all seem to work ok
| * | | make loopback compileMatt Ettus2010-07-141-0/+3
| | | |
| * | | Merge branch 'master' into u1eMatt Ettus2010-06-181-1/+2
| |\ \ \ | | | | | | | | | | | | | | | | | | | | * master: proper dependency tracking for the makefile
| * | | | added ability to clear out fifos of tx and rx.Matt Ettus2010-06-171-12/+21
| | | | |
| * | | | Merge branch 'master' into u1e_newbuildMatt Ettus2010-06-148-707/+216
| |\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Made so Makefile changes as well to get it to build * master: new make works on ise12 produces good bin files first attempt at cleaning up the build system get rid of debug stuff to help timing move u2_core into u2_rev3 directory to simplify directory structure and save headaches Conflicts: usrp2/fifo/fifo36_to_fifo18.v usrp2/top/u2_rev3/Makefile usrp2/top/u2_rev3/Makefile.udp usrp2/top/u2_rev3/u2_core_udp.v
| * | | | | debug pinsMatt Ettus2010-06-101-3/+6
| | | | | |
| * | | | | much bigger fifosMatt Ettus2010-06-101-2/+2
| | | | | |
| * | | | | proper overrun, underrun connections, debug pins.Matt Ettus2010-06-101-4/+8
| | | | | |
| * | | | | ignoresMatt Ettus2010-06-081-0/+1
| | | | | |
| * | | | | debug pinsMatt Ettus2010-06-081-1/+2
| | | | | |
| * | | | | Merge branch 'master' into u1eMatt Ettus2010-06-082-2/+2
| |\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master: allow other clock rates in vita time report ise version in build proper name for directory name build directory with ISE version name
| * | | | | | remove double declarationMatt Ettus2010-06-061-1/+1
| | | | | | |
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-18 12:21:02 +0000