aboutsummaryrefslogtreecommitdiffstats
path: root/host/lib/usrp
Commit message (Collapse)AuthorAgeFilesLines
...
* | X300: Change so radio check so it only makes sure needed frontends are ↵michael-west2016-08-101-6/+12
| | | | | | | | enabled (prevent function from disabling frontends)
* | x300: Device propagates suggested TX MTU through the mtu property, not ↵Martin Braun2016-08-092-4/+1
| | | | | | | | get_tx_hints()
* | x3xx: Enable readback of fpga_version_hashMoritz Fischer2016-08-092-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds a feature that is already present in e3xx and n230 products allowing to read back the fpga git hash the current image has been built from. The value is available via property tree at: /mboards/0/fpga_version_hash Note: A compatibility number bump is required, as otherwise the register will always read back 0 Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
* | Fix minor spelling errorDerek Kozel2016-08-091-1/+1
| |
* | Merging RFNoC support for X310Martin Braun2016-08-0923-1468/+3109
| |
* | ad936x: Loopback check now takes peeker/poker functors instead of assuming ↵Martin Braun2016-08-094-17/+23
| | | | | | | | any kind of interface
* | dboard manager: Allow deferring dboard initializationDerek Kozel2016-08-091-11/+40
| |
* | ad9361: Added option for safe SPIJonathon Pendlum2016-08-095-10/+68
| | | | | | | | - Also added check for reading chip ID
* | cores: GPIO core gets explicit DDR settingJonathon Pendlum2016-08-092-0/+7
| |
* | cores: Added shutdown option to SPI coreJonathon Pendlum2016-08-092-3/+23
| |
* | Improve LO APIs for daughterboards without configurable LOsDerek Kozel2016-08-091-5/+10
| |
* | Coerces dsp frequency to 0 if any channel uses an external LODerek Kozel2016-08-091-1/+19
| |
* | Add sleep function to dboard_ifaceKevin Gilbert2016-08-053-4/+35
| | | | | | | | | | Having this function allows a dboard_iface implementation to be aware of the timing of various calls such as SPI and register writes.
* | usb: fix 'timeout' variables to be unsigned since that is what the ↵Michael Dickens2016-08-011-2/+2
| | | | | | | | 'libusb_control_transfer' API uses.
* | common: adf5355: 'Fix' compiler warningMoritz Fischer2016-08-011-2/+2
| | | | | | | | | | | | | | GCC6 doesn't like nested /* /* */ */ comments (rightly so), and complains. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
* | B200: Adding separate B200 radio control codemichael-west2016-07-226-10/+422
| |
* | C API: wrapped multi_usrp functions for interacting with LO'sNicholas Corgan2016-07-191-1/+90
| |
* | multi_usrp: Added LO control APIDerek Kozel2016-07-191-0/+161
| |
* | Added TwinRX daughterboard control.Ashish Chaudhari2016-07-1910-0/+3845
| |
* | adf_synth: Added muxout config API to 435x controllersAshish Chaudhari2016-07-191-0/+34
| |
* | twinrx: Added ADF5355 control moduleAshish Chaudhari2016-07-193-0/+434
| | | | | | | | | | - Added regmap - Added controller class
* | x300: Minor: Assert if FPGA image identifier is not long enoughAshish Chaudhari2016-07-121-0/+2
| |
* | x300: UHD is now compatible with FPGA images with Aurora supportAshish Chaudhari2016-07-072-25/+45
| | | | | | | | | | - UHD and ZPU is now aware of Aurora SFP+ transceivers in the FPGA image - Added script to exercise Aurora BIST features
* | Merge branch 'maint'Martin Braun2016-06-233-5/+31
|\| | | | | | | | | Conflicts: host/lib/usrp/b200/b200_impl.cpp
| * b200: Update DSPs after changing tick rateMartin Braun2016-06-223-6/+32
| | | | | | | | | | Reviewed-By: Andrew Lynch <andrew.lynch@ni.com> Reviewed-By: Michael West <michael.west@ettus.com>
* | Merge branch 'maint'Martin Braun2016-06-222-6/+16
|\|
| * lib: fixed GCC 6 warnings/errorsNicholas Corgan2016-06-212-6/+16
| | | | | | | | | | * gpsd_iface: fixed ambiguity in boost::assign::list_of usage * b100/clock_ctrl: fixed "misleading indentation" warning
| * Added the option to disable ADC self-testMarcus Müller2016-06-171-1/+1
| | | | | | | | | | | | This proved helpful on devices where the EEPROM is wrong about hardware revision, and the EEPROM writing doesn't work, because the ADC self-test fails due to being run for the wrong board revision.
* | Merge branch 'maint'Martin Braun2016-06-141-6/+6
|\|
| * Spelling fixesNicholas Corgan2016-06-141-6/+6
| |
* | Merge branch 'maint'Martin Braun2016-06-141-1/+1
|\|
| * Fix off-by-one errorJonathan Wakely2016-06-071-1/+1
| | | | | | | | There's an off-by-one error in base64_decode_value that results in undefined behaviour when it's passed `'\x7b'`
* | Added the option to disable ADC self-testMarcus Müller2016-06-061-1/+1
| | | | | | | | | | | | This proved helpful on devices where the EEPROM is wrong about hardware revision, and the EEPROM writing doesn't work, because the ADC self-test fails due to being run for the wrong board revision.
* | Merge branch 'maint'Martin Braun2016-05-271-7/+26
|\|
| * UBX: Force RX LNAs on to reduce RX settling timemichael-west2016-05-261-7/+26
| |
* | Merge branch 'maint'Martin Braun2016-05-261-23/+37
|\|
| * UBX: Fixed noise issues and reduced power consumption and heatmichael-west2016-05-261-23/+37
| | | | | | | | | | - Removed force on of components to reduce noise, power consumption, and heat - Set TX PA force on only when RX antenna set to RX2 to remove long TX transient caused by HW issue on TX path
* | Merge branch 'maint'Ashish Chaudhari2016-05-263-15/+4
|\|
| * bugfix#1102: Prevented X300 DAC FIFO from underflowingAshish Chaudhari2016-05-253-15/+4
| | | | | | | | | | | | | | - The spectral distortion was begin caused by the DAC FIFO underflowing. The fix was to run through the DAC sync procedure which uses the falling edge clock to sample the RefClk and sync it with the data clk
* | x300: Fixed an issue where the wrong XB port was being selectedPaul David2016-05-191-18/+43
| | | | | | | | | | | | - If there were duplicate IPs in the mboard eeprom, the last one would be selected instead of the first - The default IP addresses (used for the case where the mboard eeprom can't be read) would overwrite the previous settings - Added a warning for duplicate IP entries in the mboard eeprom
* | x300: Check the maximum frame size for both linksPaul David2016-05-181-1/+22
| | | | | | | | | | - This change ensures that the smallest frame size is chosen with dual ethernet - It helps avoid any issues with using frame sizes larger than what the smaller link supports
* | dboard_iface: Added FE name input to set_fe_connectionAshish Chaudhari2016-05-165-15/+21
| | | | | | | | | | - A dboard_base class can have multiple frontends (subdevs) and the set_fe_connection needs to be able to distinguish between them
* | x300: Fixed false link capacity warning and cleaned up some codePaul David2016-05-132-11/+7
| | | | | | | | | | - Fixed an issue where 10GE on the HGS image presented a false warning for the link capacity - Removed some unnecessary variables after cleanup
* | Merge branch 'maint'Martin Braun2016-05-061-4/+8
|\| | | | | | | | | | | Conflicts: host/CMakeLists.txt host/lib/usrp/b200/b200_impl.cpp
| * b200: Changed implicit conversion to explicit conversion for wptrAndrew Lynch2016-05-051-2/+2
| |
| * b200: Changed tree sptr in lambda to wptrAndrew Lynch2016-05-041-2/+6
| |
* | Merge branch 'maint'Martin Braun2016-04-222-10/+18
|\| | | | | | | | | | | | | Conflicts: fpga-src host/cmake/Modules/UHDVersion.cmake host/lib/usrp/b200/b200_impl.cpp
| * b200: Fixed setting of max rateMartin Braun2016-04-222-10/+18
| | | | | | | | | | | | | | DSP rates are now being tracked as in whether or not they've been set. We can disregard unset DSPs for the automatic clock rate calculation. Reviewed-By: Derek Kozel <derek.kozel@ettus.com>
* | Merge branch 'maint'Martin Braun2016-04-201-0/+2
|\|
| * e3xx: spi: Fix issue introduced in 1b149f56Moritz Fischer2016-04-191-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Kernels (3.15+) introduce the possibility to do DUAL and QUAD spi operations via spidev. Prior to this commit nothing was setting the {tx,rx}_nbits members of the struct spi_ioc_transfer. from include/uapi/linux/spi/spidev.h struct spi_ioc_transfer { __u64 tx_buf; __u64 rx_buf; __u32 len; __u32 speed_hz; __u16 delay_usecs; __u8 bits_per_word; __u8 cs_change; __u8 tx_nbits; __u8 rx_nbits; __u16 pad; }; This turns into an issue on more recent kernels, where it turns all transactions into QUAD transactions, while the controller actually doesn't support that mode of operation. Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 19:07:31 +0000