aboutsummaryrefslogtreecommitdiffstats
path: root/host/lib/usrp
Commit message (Collapse)AuthorAgeFilesLines
* USRP1: implement MBOARD_PROP_CLOCK_CONFIG, only accepts internalJosh Blum2011-05-162-2/+11
|
* E100: fix aux codec ADC reads as per USRP1 in 6f70d1Nick Foster2011-05-161-40/+26
|
* uhd: replace managed buffer shared pointer w/ intrusive pointer to reduce ↵Josh Blum2011-05-142-25/+6
| | | | overhead
* usrp1: correct TX codec rate, it should also read 64e6 when probedJosh Blum2011-05-142-17/+11
| | | | | | We were using clock_rate*2 to simulate a codec rate of 128MHz. This reflected the old gnuradio API, but the rate between FPGA and codec is really 64MHz for both rx and tx directions.
* usrp1: apply conditional disables/enables to rx and txJosh Blum2011-05-147-9/+60
| | | | | | | | Scapped the old gnuradio code for information about VRQ_FPGA_SET_XX_ENABLE. It turns out that we should disabled + restore state when changing muxes or rates. The USRP seems to stream properly when receiving single and dual channel. Prior to this commit, tx was accicentally always disabled from a few commits ago.
* Merge branch 'tvrx2'Josh Blum2011-05-132-0/+1912
|\
| * Added TVRX2 supportJason Abele2011-05-132-0/+1912
| |
* | usrp-e100: use misc test32 register to store fpga hashJosh Blum2011-05-101-36/+34
|/
* usrp-e100: created device address arg for master clock rate, removed eeprom hackJosh Blum2011-05-125-53/+13
|
* usrp-e100: added soft sync for ad9522 clock controlJosh Blum2011-05-091-2/+12
|
* usrp_e100: work w/ ad9522 clock configurationJosh Blum2011-05-081-2/+18
|
* usrp1: overload read_eeprom to handle multi-byte readsJosh Blum2011-05-052-1/+11
|
* usrp1: added more logging to usrp1 iface for debuggingJosh Blum2011-05-051-0/+20
|
* uhd: various tweaks to log and msg, replaced a few remaining stdioJosh Blum2011-05-044-1/+4
|
* uhd: removed more iostream stuff from usrp* implementationsJosh Blum2011-05-0416-108/+99
|
* usrp-e100: removed stdio prints from implementationJosh Blum2011-05-047-80/+86
|
* uhd: replaced warning post with calls to UHD_MSG(warning)Josh Blum2011-05-0414-90/+55
| | | | | The message api can support warnings, error, and status messages. The default handler is to stdio, but the user can change this.
* uhd: replaced many conditional prints with UHD_LOG usageJosh Blum2011-05-042-13/+11
|
* usrp: replaced conditional dboard debug prints w/ UHD_LOGV(often)Josh Blum2011-05-048-83/+68
|
* usrp2: added REF_MIMO and PPS_MIMO for USRP2 clock configJosh Blum2011-05-031-15/+23
| | | | | | | | | Basically, one can tell a MIMO master to lock to MIMO ref and/or time. This is an alternative to the mimo_mode=slave/master device args. When using this alternative, one should always set the mimo_mode to maser. When in master mode, any clock config settings can be used. When in slave mode, the clock config setting are forced to MIMO_REF/PPS
* Added RSSI sensor for RFX series (not rfx400)Jason Abele2011-05-021-6/+29
|
* usrp1: toggle the FPGA reset and RX reset registers at initJosh Blum2011-05-011-8/+18
|
* usrp-e100: shrink name field to git mcr into eepromJosh Blum2011-04-201-2/+3
|
* USRP1: added support for setting clock rate from EEPROMJosh Blum2011-05-014-8/+56
| | | | | Basically, same deal as the previous changeset but for USRP1. Modified previous changes so that the key is shorter (mcr = master_clock_rate)
* usrp-e100: add ability to set/get default master clock rate from EEPROMJosh Blum2011-05-013-1/+47
| | | | | | | | | Mboard eeprom map class can parse the setting (4 byte float). The clock control will try to set the eeprom rate if present, otherwise or under failure condition, it sets the default. Updated docs, example, and provided helpful verbose. I would prefer that users burn the desired rate to the eeprom (and they may too).
* uhd: fixed typo in tune request/result inter_freq -> rf_freqJosh Blum2011-05-011-13/+13
| | | | | | | | For some reason, the code said intermediate frequency, however, it was used and treated as RF frequency. It was always intended to be the RF frequency, but was misnamed due to a cognitive distortion.
* usrp2: use default mtu as upper limit unless user specifiesJosh Blum2011-04-301-11/+12
|
* usrp2: allow devices to be discovered when usrp2_iface::make throwsJosh Blum2011-04-291-12/+16
| | | | | | | | If the discovery throws an exception, we can still yeild a discovered device. The error (which is a problem) will re-appear at make/factory time. The side effect is that a device w/ error will be discovered w/ empty serial and names. We protect against this by supporing older firmwares where i2c proto is compatible.
* usrp2: added support for GPSDO configuration bits in EEPROMJosh Blum2011-04-292-5/+38
| | | | | | | Added instructions to install and burn eeprom to documentation. Made gps_ctrl and gps_time sensor optional. Added sensors for motherboard to documentation
* GPS parser fixes for get_time.Nick Foster2011-04-292-7/+5
|
* USRP2: enable GPS by defaultNick Foster2011-04-291-3/+3
|
* USRP2: Added GPS time support to the sensors interface. gps_time sensor ↵Nick Foster2011-04-292-1/+9
| | | | returns epoch time as time_t. Untested.
* N210: implemented mboard sensors for ref lock and MIMO lockNick Foster2011-04-294-1/+28
|
* dbsrx: implement SUBDEV_PROP_ANTENNA to give users a better errorJosh Blum2011-04-281-1/+5
|
* usrp_e100: added recv/send_frame_size xport argsJosh Blum2011-04-163-11/+23
|
* rfx: reverted change, now prefer R divider to clock dividerJosh Blum2011-04-161-22/+17
| | | | | | There seems to be some issue using lower clock rates, at least on E100, I am reverting this now until I can figure out why it happens, or until I can find a more stable way to offer this feature.
* usrp1: fix for tx under remainder conditionsJosh Blum2011-04-271-3/+3
| | | | | The remainder was accidentally lost because the offset to the buffer was not propagated outside of the commit function.
* usrp1: the rx mux was reversed (fixed multi-channel rx)Josh Blum2011-04-271-1/+1
|
* Merge branch 'gdb_support'Josh Blum2011-04-2612-278/+592
|\ | | | | | | | | Conflicts: host/lib/usrp/dboard/CMakeLists.txt
| * Enhance WBX IQ balance performance through LO driveJosh Blum2011-04-261-0/+29
| |
| * wbx: split wbx into daughterboard and granddaughterboard implementationJosh Blum2011-04-264-196/+398
| |
| * usrp: support for grand daughter board eepromJosh Blum2011-04-266-6/+41
| |
| * usrp: work on dboard_manager to register an ID for multiple xcvr combinationsJosh Blum2011-04-261-75/+123
| |
* | Merge branch 'sbx-adi'Josh Blum2011-04-262-0/+794
|\ \
| * | Handle antenna switching and LEDsJason Abele2011-04-231-36/+120
| | |
| * | SBX enable LO LPF at 1.5GHzJason Abele2011-04-231-12/+31
| | |
| * | Makes 2nd SBX proto workJason Abele2011-04-231-32/+47
| | |
| * | Updating SBX to latest UHDJason Abele2011-04-231-15/+47
| | |
| * | Capture characterization changesJason Abele2011-04-231-6/+6
| | |
| * | Initial SBX-ADI driverJason Abele2011-04-232-0/+644
| |/
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-28 06:47:19 +0000