aboutsummaryrefslogtreecommitdiffstats
path: root/host/lib/usrp
Commit message (Collapse)AuthorAgeFilesLines
* uhd: replaced many conditional prints with UHD_LOG usageJosh Blum2011-05-042-13/+11
|
* usrp: replaced conditional dboard debug prints w/ UHD_LOGV(often)Josh Blum2011-05-048-83/+68
|
* usrp2: added REF_MIMO and PPS_MIMO for USRP2 clock configJosh Blum2011-05-031-15/+23
| | | | | | | | | Basically, one can tell a MIMO master to lock to MIMO ref and/or time. This is an alternative to the mimo_mode=slave/master device args. When using this alternative, one should always set the mimo_mode to maser. When in master mode, any clock config settings can be used. When in slave mode, the clock config setting are forced to MIMO_REF/PPS
* Added RSSI sensor for RFX series (not rfx400)Jason Abele2011-05-021-6/+29
|
* usrp1: toggle the FPGA reset and RX reset registers at initJosh Blum2011-05-011-8/+18
|
* usrp-e100: shrink name field to git mcr into eepromJosh Blum2011-04-201-2/+3
|
* USRP1: added support for setting clock rate from EEPROMJosh Blum2011-05-014-8/+56
| | | | | Basically, same deal as the previous changeset but for USRP1. Modified previous changes so that the key is shorter (mcr = master_clock_rate)
* usrp-e100: add ability to set/get default master clock rate from EEPROMJosh Blum2011-05-013-1/+47
| | | | | | | | | Mboard eeprom map class can parse the setting (4 byte float). The clock control will try to set the eeprom rate if present, otherwise or under failure condition, it sets the default. Updated docs, example, and provided helpful verbose. I would prefer that users burn the desired rate to the eeprom (and they may too).
* uhd: fixed typo in tune request/result inter_freq -> rf_freqJosh Blum2011-05-011-13/+13
| | | | | | | | For some reason, the code said intermediate frequency, however, it was used and treated as RF frequency. It was always intended to be the RF frequency, but was misnamed due to a cognitive distortion.
* usrp2: use default mtu as upper limit unless user specifiesJosh Blum2011-04-301-11/+12
|
* usrp2: allow devices to be discovered when usrp2_iface::make throwsJosh Blum2011-04-291-12/+16
| | | | | | | | If the discovery throws an exception, we can still yeild a discovered device. The error (which is a problem) will re-appear at make/factory time. The side effect is that a device w/ error will be discovered w/ empty serial and names. We protect against this by supporing older firmwares where i2c proto is compatible.
* usrp2: added support for GPSDO configuration bits in EEPROMJosh Blum2011-04-292-5/+38
| | | | | | | Added instructions to install and burn eeprom to documentation. Made gps_ctrl and gps_time sensor optional. Added sensors for motherboard to documentation
* GPS parser fixes for get_time.Nick Foster2011-04-292-7/+5
|
* USRP2: enable GPS by defaultNick Foster2011-04-291-3/+3
|
* USRP2: Added GPS time support to the sensors interface. gps_time sensor ↵Nick Foster2011-04-292-1/+9
| | | | returns epoch time as time_t. Untested.
* N210: implemented mboard sensors for ref lock and MIMO lockNick Foster2011-04-294-1/+28
|
* dbsrx: implement SUBDEV_PROP_ANTENNA to give users a better errorJosh Blum2011-04-281-1/+5
|
* usrp_e100: added recv/send_frame_size xport argsJosh Blum2011-04-163-11/+23
|
* rfx: reverted change, now prefer R divider to clock dividerJosh Blum2011-04-161-22/+17
| | | | | | There seems to be some issue using lower clock rates, at least on E100, I am reverting this now until I can figure out why it happens, or until I can find a more stable way to offer this feature.
* usrp1: fix for tx under remainder conditionsJosh Blum2011-04-271-3/+3
| | | | | The remainder was accidentally lost because the offset to the buffer was not propagated outside of the commit function.
* usrp1: the rx mux was reversed (fixed multi-channel rx)Josh Blum2011-04-271-1/+1
|
* Merge branch 'gdb_support'Josh Blum2011-04-2612-278/+592
|\ | | | | | | | | Conflicts: host/lib/usrp/dboard/CMakeLists.txt
| * Enhance WBX IQ balance performance through LO driveJosh Blum2011-04-261-0/+29
| |
| * wbx: split wbx into daughterboard and granddaughterboard implementationJosh Blum2011-04-264-196/+398
| |
| * usrp: support for grand daughter board eepromJosh Blum2011-04-266-6/+41
| |
| * usrp: work on dboard_manager to register an ID for multiple xcvr combinationsJosh Blum2011-04-261-75/+123
| |
* | Merge branch 'sbx-adi'Josh Blum2011-04-262-0/+794
|\ \
| * | Handle antenna switching and LEDsJason Abele2011-04-231-36/+120
| | |
| * | SBX enable LO LPF at 1.5GHzJason Abele2011-04-231-12/+31
| | |
| * | Makes 2nd SBX proto workJason Abele2011-04-231-32/+47
| | |
| * | Updating SBX to latest UHDJason Abele2011-04-231-15/+47
| | |
| * | Capture characterization changesJason Abele2011-04-231-6/+6
| | |
| * | Initial SBX-ADI driverJason Abele2011-04-232-0/+644
| |/
* / xcvr2450: initialize the max_power variableJosh Blum2011-04-261-1/+1
|/
* uhd: move thread loop condition flag to before barrier (prevents race condition)Josh Blum2011-04-222-2/+2
|
* Merge branch 'usrp2/discover_with_old_fw'Josh Blum2011-04-193-38/+81
|\
| * usrp2: improve the compatibility error messagesJosh Blum2011-04-192-8/+7
| |
| * usrp2: use the firmware's discovered compat numberJosh Blum2011-04-131-4/+16
| |
| * usrp2: add check for holler protocol, we can support backwardsJosh Blum2011-04-132-15/+29
| |
| * usrp2: support fw protos with older compats for various partsJosh Blum2011-04-082-20/+38
| | | | | | | | | | | | | | | | | | | | i2c, spi, and uart are long time no changing registers changed recently (think re-map) also, perform the fpga compat check in the make now we can find devices with out of date images
* | rfx: changes to pick from the dboard clock rates and use R=1Josh Blum2011-04-181-17/+22
| |
* | Updated documentation and improved XCVR RSSI calculationJason Abele2011-04-141-2/+11
| | | | | | | | | | | | | | | | | | | | Documented dboard sensors Documented DBSRX2 Added description of direct conversion vs low IF for each dboard Added E1xx docs for adding refclock and pps connectors XCVR rssi calculation was in unscaled dB units Used chart in datasheet (pg 16) to rescale to dBm
* | usrp-e100: reset dboard clocks on rate change, and dont cache in dboard ifaceJosh Blum2011-04-073-4/+32
|/
* uhd: define LINUX in build system to simplify some checksJosh Blum2011-04-011-5/+1
|
* Merge branch 'use_boost_barrier'Josh Blum2011-04-013-24/+31
|\
| * uhd: implemented boost barriers on all code that creates threadsJosh Blum2011-03-313-24/+31
| | | | | | | | | | | | | | | | | | The barrier ensures that the thread must spawn before the caller exits. Some of the code already used a mutex to accomplish this, however cygwin chokes when a mutex is locked twice by the same thread. Mutex implementations were replaced with the barrier implementation. Also the barrier implementation is far cleaner.
* | Merge branch 'rfx400_tx'Josh Blum2011-04-011-3/+6
|\ \
| * | Correct RFX400 div2 logic, makes RFX400 TX workJason Abele2011-03-311-3/+6
| | |
* | | usrp1: fixed codec ctrl aux adc read (didnt start conversions) + cleaned-up ↵Josh Blum2011-03-301-44/+29
| | | | | | | | | | | | logic
* | | usrp1: switch usrp1 iface to use spi read (transact never worked)Josh Blum2011-03-301-17/+29
| |/ |/| | | | | It detects the number of header bytes by searching for non-zero bytes.
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 13:08:09 +0000