| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Adds a ZPU register to control the FP GPIO source. These are 2bits
per GPIO pin, totalling 24 bits. 0 corresponds to RF-A, 1 corresponds
to RF-B. The following Python code will control the upper 6 bits of the
front-panel GPIO from the B-side radio on an X300:
>>> import uhd
>>> U = uhd.usrp.MultiUSRP("type=x300")
>>> U.get_gpio_src_banks()
['FP0']
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFA', 'RFA']
>>> U.set_gpio_src("FP0", ['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA',
'RFB', 'RFB', 'RFB', 'RFB', 'RFB', 'RFB'])
>>> U.get_gpio_src("FP0")
['RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFA', 'RFB', 'RFB', 'RFB', 'RFB',
'RFB', 'RFB']
>>> # Make all GPIOs outputs:
>>> U.set_gpio_attr("FP0A", "DDR", 0xFFF)
>>> U.set_gpio_attr("FP0B", "DDR", 0xFFF)
>>> # Control all GPIOs from software (not ATR):
>>> U.set_gpio_attr("FP0A", "CTRL", 0x000)
>>> U.set_gpio_attr("FP0B", "CTRL", 0x000)
>>> # Bottom 3 pins go high from radio A
>>> U.set_gpio_attr("FP0A", "OUT", 0x007)
>>> # Top 3 pins go high from radio B
>>> U.set_gpio_attr("FP0B", "OUT", 0xE00)
Amends the gpio.cpp example to allow switching the source.
Co-authored-by: Brent Stapleton <brent.stapleton@ettus.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds a separate version of multi_usrp for RFNoC devices. It is
compatible with RFNoC devices only, and prefers C++ APIs over property
tree usage. The factory of multi_usrp is modified such that it picks the
correct version, users of multi_usrp don't care about this change.
This also introduces some API changes:
- Removing redundant GPIO functions. Now all GPIO control, setting, and
readback is done with uint32_t's.
- Adding getter/setter for GPIO source. This was done to simplify the
other GPIO settings, as the source for each pin is not always a
binary. The CTRL mode, for example, can either be ATR or GPIO.
However, the source can be controlled by various radios or "PS" or
some other source.
- Removing the mask from the RFNoC radio controllers' set_gpio_attr().
- Adding state caching to gpio_atr_3000, and a getter for it. Whenever
an attribute is set, that value is cached, and can now be retreieved.
- Remove low-level register API. Since UHD 3.10, there is no USRP that
implements that API.
Modifying the filter API in the following ways:
- Splitting filter API getter/setter/list into separate RX and TX
functions
- Adding channel numbers as an argument
- The filter name will no longer be a property tree path, but rather a
filter name. For RFNoC devices, this will take the form
`BLOCK_ID:FILTER_NAME`. For non-RFNoC devices, this will just be the
filter name (e.g. `HB_1`)
- Removing search mask from listing function. Users can do their own
searching
Co-Authored-By: Martin Braun <martin.braun@ettus.com>
|
