aboutsummaryrefslogtreecommitdiffstats
path: root/fpga/usrp3/lib
Commit message (Collapse)AuthorAgeFilesLines
* fpga: lib: Update example constraint in synchronizerWade Fife2021-09-131-18/+40
|
* fpga: Remove stale references to UHD_FPGA_DIRWade Fife2021-09-087-14/+7
|
* sim: Update chdr_16sc_to_sc12 testbenchmichael-west2021-08-101-137/+159
| | | | | | | Modified to send 2 packets back to back at each packet size to test output during sequential input packets. Also fixed whitespace. Signed-off-by: michael-west <michael.west@ettus.com>
* fpga: Re-order error and data packetsmichael-west2021-08-101-2/+28
| | | | | | | Added delay to error packets so overrun error is back in-band. Avoids dropping good data packets in the case of an overrun. Signed-off-by: michael-west <michael.west@ettus.com>
* fpga: Fix sc16 to sc12 convertermichael-west2021-08-101-62/+80
| | | | | | | | | Re-wrote converter to remove clock cycle delay on i_tready when handling residual output and fixed improper handling of tlast during residual data processing. Resolves some USB overflow issues when using sc12 data type on B200 devices. Signed-off-by: michael-west <michael.west@ettus.com>
* fpga: rfnoc: Fix EOB loss in DUCWade Fife2021-08-087-218/+1858
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | There were some rare corner cases where the EOB could get lost in the DUC due to the dds_timed logic not always passing it through as it should. This resulted in an underflow error message at the end of transmission. This commit also fixes an issue where part of the last packet used a frequency shift of 0 instead of the requested frequency shift, and an issue where the first few samples of a burst used the wrong frequency shift value. Part of the fix includes adding a TUSER port to dds_sin_cos_lut_only. The TUSER port is built into the IP but was disabled. It is now enabled and set to 1 bit wide. This has a very small effect on resource usage and can be left unconnected when not needed. The dds_freq_tune block was shared by the DUC and DDC. To avoid affecting the DDC, a new version, dds_freq_tune_duc, is being added for the DUC to use that has the necessary fixes. The new dds_wrapper.v is a wrapper for the dds_sin_cos_lut_only IP. This IP has the undesirable behavior that new inputs must be provided to push previous outputs through the IP. This wrapper hides that complexity by adding some logic to ensure all data gets pushed through automatically. This logic uses the TUSER port on the IP. Finally, a testbench for dds_timed was added.
* fpga: lib: Clean up and document lib filesWade Fife2021-08-083-246/+411
| | | | Clean-up and document axi_tag_time, dds_freq_tune, and axi_sync.
* rfnoc: duc: Remove stale references to CORDICWade Fife2021-08-081-18/+15
| | | | | Updated some comments that still referenced the old CORDIC implementation, which is no longer used.
* fpga: Update testbenches to work in ModelSimWade Fife2021-06-173-47/+71
|
* fpga: lib: Update register comments in eth_regs.vhWade Fife2021-06-101-1/+5
|
* fpga: lib: Add modports to SV AXI-Stream blocksWade Fife2021-06-034-8/+8
|
* fpga: lib: Add time_increment port to timekeeperWade Fife2021-06-031-17/+43
| | | | | Adds a time_increment port for situations in which the parameter TIME_INCREMENT can't be used. They offer the same behavior.
* fpga: lib: Pipeline ctrlport_timerWade Fife2021-06-031-24/+81
| | | | | | | This pipelines ctrlport_timer to eliminate the long combinational path caused by the time comparisons. This change also removes the PRECISION_BITS parameter and converts it to a signal named time_ignore_bits.
* fpga: lib: Add clock domain comments to interfacesWade Fife2021-06-037-13/+28
|
* fpga: lib: Add 2 to 1 gearbox moduleWade Fife2021-06-035-0/+517
|
* fpga: lib: Add AXI4 (full) interfaceAndrew Moch2021-06-034-0/+619
| | | | | Add a SystemVerilog interface for connecting AXI4 ports, and an associated header file with helper macros.
* fpga: lib: add pause support to ethernet xportAndrew Moch2021-06-036-7/+112
|
* fpga: lib: Add eth_ipv4_internalWade Fife2021-06-032-0/+442
| | | | | This adds a generic version of eth_internal that allows you to specify the CHDR width.
* fpga: lib: Add zynquplus family to axi_bitqHumberto Jimenez2021-06-031-12/+13
|
* fpga: lib: Minor cleanup of axi_lite.vhLars Amsel2021-06-031-2/+23
|
* fpga: rfnoc: Add ability to disable output flow controlWade Fife2021-04-142-7/+22
| | | | | | | | | | | | | Per the RFNoC specification, if we set the frequency of flow control updates to 0 then the input stream will not send flow control status updates to the output stream handler. This change makes it so that when the frequency of flow control status updates is configured to be zero in the FPGA output stream handler (i.e., cfg_fc_freq_bytes and cfg_fc_freq_pkts are both 0 in chdr_stream_output) then the output stream handler will not use flow control. That is, chdr_stream_output will not expect stream status updates and will not restrict output packets.
* fpga: lib: Add rx_front_end_gen3 testbenchWade Fife2021-04-092-0/+247
|
* fpga: lib: Update round_sd to eliminate X from simulationWade Fife2021-04-091-14/+45
| | | | | | | | | | | | The asynchronous feedback loop on the err signal causes X to get stuck on the sum signal when simulating. This change adds a check for simulation only to force X to 0 so that unknown inputs get resolved once the inputs are known. Also added default values to the ports out and strobe_out, since having them uninitialized and without reset was causing simulation issues in other modules. The FPGA will initialize them to 0, so this change makes the code equivalent to real hardware behavior.
* fpga: lib: Fix simulation of axi_fir_filterWade Fife2021-04-091-1/+1
| | | | | | The always(*) block was never executing in some simulators because there were no signals on the right-hand side in the block. Changing it to an initial block ensures it always runs.
* TwinRX: Remove frontend filtermichael-west2021-04-081-59/+8
| | | | | | | | | | Removing the FIR filter in the frontend to reclaim resources and remove redundancy when using a DDC block. The default image has a DDC block, so only users making custom RFNoC images and using TwinRX will need to take care to properly downconvert the full bandwidth coming from the radio block. Signed-off-by: michael-west <michael.west@ettus.com>
* fpga: docs: Improve documentation of rx_frontend_gen3Martin Braun2021-04-071-1/+73
| | | | Also fixes a typo in the calibration manual page.
* fpga: lib: Fix DDS_SIN_COS_LUT outputs in makefilePaul Butler2021-03-311-1/+1
|
* fpga: dsp: Fix formatting of rx_dcoffset and add docsMartin Braun2021-03-091-38/+110
| | | | | - Adapt to coding guide - Add header that explains the module
* fpga: e320: Improve timing on LVDS interfaceWade Fife2020-12-113-355/+539
|
* fpga: lib: add glitch free mux moduleMax Köhler2020-12-032-0/+30
|
* fpga: lib: Fix axis_strm_monitor parametersWade Fife2020-10-201-2/+2
|
* fpga: lib: Fix small packets stuck in 10 GbE TXAndrew Moch2020-10-051-3/+17
| | | | | | Any packet less than CUT_THROUGH bytes has a high chance of getting stuck in the TX FIFO of the xge_mac_wrapper. In cut-through mode we were waiting for CUT_THROUGH bytes before transmitting the packet.
* fpga: lib: Fix 10 GbE cut-through modeAndrew Moch2020-09-161-4/+16
| | | | | | | When operating in cut-through mode the hold off from the MAC was not applying back pressure, so when the TX interface filled up, data was dropped. This bug was introduced when cut-through was added, and does not impact the original implementation.
* fpga: lib: add generic to disable bitq engine tri-statingMax Köhler2020-09-162-11/+16
|
* fpga: sim: chdr_stream_endpoint_tb improvementsWade Fife2020-08-312-36/+150
| | | | | | | - Adds test coverage for stream command and status packets - Cleans up report output during simulation - Stops clocks at the end of simulation, so chdr_stream_endpoint_tb can be run directly instead of just chdr_stream_endpoint_all_tb
* fpga: rfnoc: Update CHDR stream INIT commandWade Fife2020-08-281-3/+10
| | | | | | This changes the behavior of the stream command with the INIT OpCode such that sending the command with 0 for the values causes no flow control stream status packets to be sent in response to incoming data.
* fpga: lib: Fix lint warningsWade Fife2020-08-283-3/+3
| | | | | Fixes various synthesis/simulation warnings that were being generated due to incorrectly sized constants.
* fpga: rfnoc: Remove deprecated filesWade Fife2020-08-2322-2674/+5
|
* fpga: lib: Add more CtrlPort constantsWade Fife2020-08-191-7/+12
| | | | Add some missing CtrlPort signal widths to ctrlport.vh.
* fpga: lib: Add ctrlport_to_regport bridgeWade Fife2020-08-192-0/+91
|
* fpga: rfnoc: Enable clean switch in SwitchboardWade Fife2020-08-131-1/+1
| | | | | This change prevents packets from being chopped midway if the switchboard configuration is changed when a packet is in flight.
* fpga: lib: Fix SWITCH_ON_LAST in axi_mux_selectWade Fife2020-08-131-18/+39
| | | | | Thange allows the mux to switch cleanly between packets, if the mux select input is changed while a packet is in flight.
* fpga: lib: add handshake to replace FIFO for ctrlport CDCMax Köhler2020-08-133-48/+143
| | | | | | | | The clock crossing of the ctrlport used FIFOs to transfer requests and responses between clock domains. This commit adds a handshake based on the pulse synchronizer to reduce the resource usage for ctrlport clock domain crossing. Data is stored in a single register while the pulse synchronizer handles the signaling of valid flags.
* fpga: rfnoc: Fix clock crossing in axis_data_to_chdrWade Fife2020-08-121-69/+89
| | | | | | | | | This fixes some incorrectly handled clock crossings from axis_data_clk to axis_chdr_clk, which could have manifested as timing failures (on E320) or incorrect behavior, depending on the product and noc_shell configuration. Also cleans up trailing white space.
* fpga: lib: Change max FFT size to 1024Wade Fife2020-08-111-2/+2
| | | | | | | | | | | | | The max FFT size was 4096, but we don't currently have any devices that can do that without modification. This is because, currently, the FFT size must be the same as the packet size, and the largest packet size supported by most devices is about 8000 bytes, or 2000 sc16 samples. Therefore, the largest FFT size supported without modifying other code is 1024 samples. This change frees up about 21% of the LUTs and 36% of the BRAM used by axi_fft and makes the software block controller and the IP agree on the maximum FFT size.
* fpga: rfnoc: Add tests to FFT blockWade Fife2020-08-102-39/+202
| | | | | This adds additional tests to the testbench to cover register reads and basic IFFT functionaltiy.
* fpga: lib: add Intel MAX10 architecture for 2clk FIFOMax Köhler2020-08-062-28/+33
| | | | | | | | | | | | | This commit derives parameters for MAX10 devices if provided by the DEVICE parameter. MAX10 devices FIFO generator support up to 36 bit wide FIFOs using embedded memory (M9K) in simple dual port mode, which is treated equally to RAM in the parameters. In combination with sorting the ctrlport signals by usage, the used resources can be reduced on the MAX10 devices from 6 to 3 M9K blocks for a ctrlport_clk_cross instance without time and portids.
* fpga: lib: Update xport_svAndrew Moch2020-08-056-182/+437
| | | | | | | | | - Detect dropped words at the dispatch level. This prevents an overflow on CHDR from block CPU. - Dropped packets are recorded as CPU or CHDR drop count - Refactor to put chdr_xport_adapter.sv in different clock domain to improve timing - Unwrinkle tkeep/trailing transitions
* fpga: rfnoc: Add RFNoC Keep One in N blockAaron Rossetto2020-08-057-0/+1432
|
* fpga: rfnoc: Add RFNoC Replay blockWade Fife2020-08-0411-875/+4101
|
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-29 04:31:25 +0000