uhd - Ettus' UHD Repository

	Commit message (Collapse)	Author	Age	Files	Lines
*	B100: use FPGA external reset on init	Nick Foster	2012-02-06	1	-1/+6
\|
*	B100/B150: firmware disable FIFOs until host enables to keep junk out	Nick Foster	2012-02-03	2	-8/+11
\|
*	b100: bump compat numbers for slave fifo mode	Josh Blum	2012-02-01	1	-1/+1
\| \| \| \| \| \|	Conflicts: host/lib/usrp/b100/b100_impl.hpp
*	B100 firmware changes to allow slave mode TX/RX.	Nick Foster	2012-02-01	4	-162/+59
\|
*	Fixing VID comment in firmware to reflect ERLLC rather than FSF.	Ben Hilburn	2011-10-14	1	-1/+1
\|
*	b100: new eeprom map for special 9 byte serial	Josh Blum	2011-10-12	2	-4/+5
\|
*	B100: change B100 PID in usb_descriptors.a51 as well	Nick Foster	2011-10-11	1	-1/+1
\|
*	B100: use PA6 for pktend	Nick Foster	2011-10-10	1	-2/+1
\|
*	1 Character Patch for USRP1 usrp_eeprom.bin generation	Jason Abele	2011-10-10	1	-1/+1
\|
*	B100: modify build_eeprom for correct B100 PID	Nick Foster	2011-10-10	1	-1/+1
\|
*	B100 firmware fix for FPGA load race condition, plus a little cleanup for ↵	Nick Foster	2011-10-10	2	-19/+14
\| \| \| \|	readability
*	b100: added b100 firmware (squashed)	Josh Blum	2011-06-14	18	-4/+2127
\|
*	usrp1: reverted spi transaction changes to the usrp1 firmware (broken and ↵	Josh Blum	2011-03-30	4	-116/+3
\| \| \| \|	not needed)
*	uhd: rename identifier for usrp1 eeprom, and fix offsets, add serial support ↵	Josh Blum	2010-11-05	1	-1/+1
\| \| \| \|	to usrp2
*	Merge branch 'good_stuff' into mb_eeprom	Josh Blum	2010-11-05	116	-4066/+528
\|\ \| \| \| \| \| \| \| \|	Conflicts: firmware/fx2/include
\| *	usrp1: pulled in cmake build system for usrp1 firmware	Josh Blum	2010-11-05	117	-4066/+529
\|/
*	EEPROM burning in UHD. Changed some USB device handle stuff. Added ↵	Nick Foster	2010-08-31	2	-133/+28
\| \| \| \|	usrp_init_eeprom.cpp. Hacked up the firmware makefile to behave and to generate .bin EEPROM images instead of IHX.
*	usrp1: images for usrp1, makefile checks for image generation dependencies	Josh Blum	2010-08-19	1	-0/+5
\|
*	usrp1: Add SPI transaction command to FX2 firmware	Thomas Tsou	2010-08-13	4	-3/+116
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	The existing SPI read command is set for half-duplex 8-bit or 16-bit writes followed by an equivalent sized read. This patch adds a new command, VRQ_SPI_TRANSACT, which performs a full-duplex transaction up to 4-bytes. Since the data buffer of the USB control transfer is not available for outbound data on IN requests, the 4 bytes of write data are sent through the request parameters. Enables are sent in the previsouly unused high byte of the length parameter. The USB field mappings are shown below. Only rising edge and MSB operation is supported. Field (8-bit) Description ===== ===== bmRequestType 0x80 (USB Device IN request) bRequest 0x83 (VRQ_SPI_TRANSACT) wValueH OUT data(0) wValueL OUT data(1) wIndexH OUT data(2) wIndexL OUT data(3) wLengthH SPI enables wLengthL Number of bytes to transfer (1-4) EP0BUF IN data
*	usrp1: Add FX2 firmware files	Thomas Tsou	2010-08-13	107	-0/+11421
	These firmware files for the usrp1 are imported from GNURadio.