diff options
Diffstat (limited to 'host')
| -rw-r--r-- | host/utils/CMakeLists.txt | 4 | ||||
| -rw-r--r-- | host/utils/usrp-e-debug-pins.c | 77 | ||||
| -rw-r--r-- | host/utils/usrp_e_regs.hpp | 196 |
3 files changed, 277 insertions, 0 deletions
diff --git a/host/utils/CMakeLists.txt b/host/utils/CMakeLists.txt index 0e3f81d0a..6515048eb 100644 --- a/host/utils/CMakeLists.txt +++ b/host/utils/CMakeLists.txt @@ -30,11 +30,15 @@ TARGET_LINK_LIBRARIES(fpga-downloader) ADD_EXECUTABLE(usrp-e-loopback usrp-e-loopback.c) TARGET_LINK_LIBRARIES(usrp-e-loopback pthread) +ADD_EXECUTABLE(usrp-e-debug-pins usrp-e-debug-pins.c) +TARGET_LINK_LIBRARIES(usrp-e-debug-pins) + INSTALL(TARGETS uhd_find_devices uhd_usrp_probe fpga-downloader usrp-e-loopback + usrp-e-debug-pins RUNTIME DESTINATION ${RUNTIME_DIR} ) diff --git a/host/utils/usrp-e-debug-pins.c b/host/utils/usrp-e-debug-pins.c new file mode 100644 index 000000000..1ed2c8983 --- /dev/null +++ b/host/utils/usrp-e-debug-pins.c @@ -0,0 +1,77 @@ +#include <stdio.h> +#include <stdlib.h> +#include <unistd.h> +#include <sys/types.h> +#include <fcntl.h> +#include <string.h> +#include <sys/ioctl.h> + +#include <linux/usrp_e.h> +#include "usrp_e_regs.hpp" + +// Usage: usrp_e_gpio <string> + +static int fp; + +static int read_reg(__u16 reg) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + ret = ioctl(fp, USRP_E_READ_CTL16, &d); + return d.buf[0]; +} + +static void write_reg(__u16 reg, __u16 val) +{ + int ret; + struct usrp_e_ctl16 d; + + d.offset = reg; + d.count = 1; + d.buf[0] = val; + ret = ioctl(fp, USRP_E_WRITE_CTL16, &d); +} + +int main(int argc, char *argv[]) +{ + int test; + + test = 0; + if (argc < 2) { + printf("%s 0|1|off\n", argv[0]); + } + + fp = open("/dev/usrp_e0", O_RDWR); + printf("fp = %d\n", fp); + if (fp < 0) { + perror("Open failed"); + return -1; + } + + if (strcmp(argv[1], "0") == 0) { + printf("Selected 0 based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_TX_SEL, 0x0); + write_reg(UE_REG_GPIO_RX_SEL, 0x0); + write_reg(UE_REG_GPIO_TX_DBG, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DBG, 0xFFFF); + } else if (strcmp(argv[1], "1") == 0) { + printf("Selected 1 based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DDR, 0xFFFF); + write_reg(UE_REG_GPIO_TX_SEL, 0xFFFF); + write_reg(UE_REG_GPIO_RX_SEL, 0xFFFF); + write_reg(UE_REG_GPIO_TX_DBG, 0xFFFF); + write_reg(UE_REG_GPIO_RX_DBG, 0xFFFF); + } else { + printf("Selected off based on %s\n", argv[1]); + write_reg(UE_REG_GPIO_TX_DDR, 0x0); + write_reg(UE_REG_GPIO_RX_DDR, 0x0); + } + + return 0; +} diff --git a/host/utils/usrp_e_regs.hpp b/host/utils/usrp_e_regs.hpp new file mode 100644 index 000000000..a4f42093e --- /dev/null +++ b/host/utils/usrp_e_regs.hpp @@ -0,0 +1,196 @@ + + +//////////////////////////////////////////////////////////////// +// +// Memory map for embedded wishbone bus +// +//////////////////////////////////////////////////////////////// + +// All addresses are byte addresses. All accesses are word (16-bit) accesses. +// This means that address bit 0 is usually 0. +// There are 11 bits of address for the control. + +#ifndef __USRP_E_REGS_H +#define __USRP_E_REGS_H + +///////////////////////////////////////////////////// +// Slave pointers + +#define UE_REG_SLAVE(n) ((n)<<7) +#define UE_REG_SR_ADDR(n) ((UE_REG_SLAVE(5)) + (4*(n))) + +///////////////////////////////////////////////////// +// Slave 0 -- Misc Regs + +#define UE_REG_MISC_BASE UE_REG_SLAVE(0) + +#define UE_REG_MISC_LED UE_REG_MISC_BASE + 0 +#define UE_REG_MISC_SW UE_REG_MISC_BASE + 2 +#define UE_REG_MISC_CGEN_CTRL UE_REG_MISC_BASE + 4 +#define UE_REG_MISC_CGEN_ST UE_REG_MISC_BASE + 6 +#define UE_REG_MISC_TEST UE_REG_MISC_BASE + 8 +#define UE_REG_MISC_RX_LEN UE_REG_MISC_BASE + 10 +#define UE_REG_MISC_TX_LEN UE_REG_MISC_BASE + 12 + +///////////////////////////////////////////////////// +// Slave 1 -- UART +// CLKDIV is 16 bits, others are only 8 + +#define UE_REG_UART_BASE UE_REG_SLAVE(1) + +#define UE_REG_UART_CLKDIV UE_REG_UART_BASE + 0 +#define UE_REG_UART_TXLEVEL UE_REG_UART_BASE + 2 +#define UE_REG_UART_RXLEVEL UE_REG_UART_BASE + 4 +#define UE_REG_UART_TXCHAR UE_REG_UART_BASE + 6 +#define UE_REG_UART_RXCHAR UE_REG_UART_BASE + 8 + +///////////////////////////////////////////////////// +// Slave 2 -- SPI Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_SPI_BASE UE_REG_SLAVE(2) + +//spi slave constants +#define UE_SPI_SS_AD9522 (1 << 3) +#define UE_SPI_SS_AD9862 (1 << 2) +#define UE_SPI_SS_TX_DB (1 << 1) +#define UE_SPI_SS_RX_DB (1 << 0) + +//////////////////////////////////////////////// +// Slave 3 -- I2C Core +// This should be accessed through the IOCTL +// Users should not touch directly + +#define UE_REG_I2C_BASE UE_REG_SLAVE(3) + + +//////////////////////////////////////////////// +// Slave 4 -- GPIO + +#define UE_REG_GPIO_BASE UE_REG_SLAVE(4) + +#define UE_REG_GPIO_RX_IO UE_REG_GPIO_BASE + 0 +#define UE_REG_GPIO_TX_IO UE_REG_GPIO_BASE + 2 +#define UE_REG_GPIO_RX_DDR UE_REG_GPIO_BASE + 4 +#define UE_REG_GPIO_TX_DDR UE_REG_GPIO_BASE + 6 +#define UE_REG_GPIO_RX_SEL UE_REG_GPIO_BASE + 8 +#define UE_REG_GPIO_TX_SEL UE_REG_GPIO_BASE + 10 +#define UE_REG_GPIO_RX_DBG UE_REG_GPIO_BASE + 12 +#define UE_REG_GPIO_TX_DBG UE_REG_GPIO_BASE + 14 + +//possible bit values for sel when dbg is 0: +#define GPIO_SEL_SW 0 // if pin is an output, set by software in the io reg +#define GPIO_SEL_ATR 1 // if pin is an output, set by ATR logic + +//possible bit values for sel when dbg is 1: +#define GPIO_SEL_DEBUG_0 0 // if pin is an output, debug lines from FPGA fabric +#define GPIO_SEL_DEBUG_1 1 // if pin is an output, debug lines from FPGA fabric + + +//////////////////////////////////////////////////// +// Slave 5 -- Settings Bus +// +// Output-only, no readback, 32 registers total +// Each register must be written 32 bits at a time +// First the address xxx_xx00 and then xxx_xx10 + +#define UE_REG_SETTINGS_BASE UE_REG_SLAVE(5) + +/////////////////////////////////////////////////// +// Slave 6 -- ATR Controller +// 16 regs + +#define UE_REG_ATR_BASE UE_REG_SLAVE(6) + +#define UE_REG_ATR_IDLE_RXSIDE UE_REG_ATR_BASE + 0 +#define UE_REG_ATR_IDLE_TXSIDE UE_REG_ATR_BASE + 2 +#define UE_REG_ATR_INTX_RXSIDE UE_REG_ATR_BASE + 4 +#define UE_REG_ATR_INTX_TXSIDE UE_REG_ATR_BASE + 6 +#define UE_REG_ATR_INRX_RXSIDE UE_REG_ATR_BASE + 8 +#define UE_REG_ATR_INRX_TXSIDE UE_REG_ATR_BASE + 10 +#define UE_REG_ATR_FULL_RXSIDE UE_REG_ATR_BASE + 12 +#define UE_REG_ATR_FULL_TXSIDE UE_REG_ATR_BASE + 14 + +///////////////////////////////////////////////// +// DSP RX Regs +//////////////////////////////////////////////// +#define UE_REG_DSP_RX_FREQ UE_REG_SR_ADDR(0) +#define UE_REG_DSP_RX_SCALE_IQ UE_REG_SR_ADDR(1) // {scale_i,scale_q} +#define UE_REG_DSP_RX_DECIM_RATE UE_REG_SR_ADDR(2) // hb and decim rate +#define UE_REG_DSP_RX_DCOFFSET_I UE_REG_SR_ADDR(3) // Bit 31 high sets fixed offset mode, using lower 14 bits, // otherwise it is automatic +#define UE_REG_DSP_RX_DCOFFSET_Q UE_REG_SR_ADDR(4) // Bit 31 high sets fixed offset mode, using lower 14 bits +#define UE_REG_DSP_RX_MUX UE_REG_SR_ADDR(5) + +/////////////////////////////////////////////////// +// VITA RX CTRL regs +/////////////////////////////////////////////////// +// The following 3 are logically a single command register. +// They are clocked into the underlying fifo when time_ticks is written. +#define UE_REG_CTRL_RX_STREAM_CMD UE_REG_SR_ADDR(8) // {now, chain, num_samples(30) +#define UE_REG_CTRL_RX_TIME_SECS UE_REG_SR_ADDR(9) +#define UE_REG_CTRL_RX_TIME_TICKS UE_REG_SR_ADDR(10) +#define UE_REG_CTRL_RX_CLEAR_OVERRUN UE_REG_SR_ADDR(11) // write anything to clear overrun +#define UE_REG_CTRL_RX_VRT_HEADER UE_REG_SR_ADDR(12) // word 0 of packet. FPGA fills in packet counter +#define UE_REG_CTRL_RX_VRT_STREAM_ID UE_REG_SR_ADDR(13) // word 1 of packet. +#define UE_REG_CTRL_RX_VRT_TRAILER UE_REG_SR_ADDR(14) +#define UE_REG_CTRL_RX_NSAMPS_PER_PKT UE_REG_SR_ADDR(15) +#define UE_REG_CTRL_RX_NCHANNELS UE_REG_SR_ADDR(16) // 1 in basic case, up to 4 for vector sources + +///////////////////////////////////////////////// +// DSP TX Regs +//////////////////////////////////////////////// +#define UE_REG_DSP_TX_FREQ UE_REG_SR_ADDR(17) +#define UE_REG_DSP_TX_SCALE_IQ UE_REG_SR_ADDR(18) // {scale_i,scale_q} +#define UE_REG_DSP_TX_INTERP_RATE UE_REG_SR_ADDR(19) +#define UE_REG_DSP_TX_UNUSED UE_REG_SR_ADDR(20) +#define UE_REG_DSP_TX_MUX UE_REG_SR_ADDR(21) + +///////////////////////////////////////////////// +// VITA TX CTRL regs +//////////////////////////////////////////////// +#define UE_REG_CTRL_TX_NCHANNELS UE_REG_SR_ADDR(24) +#define UE_REG_CTRL_TX_CLEAR_UNDERRUN UE_REG_SR_ADDR(25) +#define UE_REG_CTRL_TX_REPORT_SID UE_REG_SR_ADDR(26) +#define UE_REG_CTRL_TX_POLICY UE_REG_SR_ADDR(27) + +#define UE_FLAG_CTRL_TX_POLICY_WAIT (0x1 << 0) +#define UE_FLAG_CTRL_TX_POLICY_NEXT_PACKET (0x1 << 1) +#define UE_FLAG_CTRL_TX_POLICY_NEXT_BURST (0x1 << 2) + +///////////////////////////////////////////////// +// VITA49 64 bit time (write only) +//////////////////////////////////////////////// + /*! + * \brief Time 64 flags + * + * <pre> + * + * 3 2 1 + * 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 + * +-----------------------------------------------------------+-+-+ + * | |S|P| + * +-----------------------------------------------------------+-+-+ + * + * P - PPS edge selection (0=negedge, 1=posedge, default=0) + * S - Source (0=sma, 1=mimo, 0=default) + * + * </pre> + */ +#define UE_REG_TIME64_SECS UE_REG_SR_ADDR(28) // value to set absolute secs to on next PPS +#define UE_REG_TIME64_TICKS UE_REG_SR_ADDR(29) // value to set absolute ticks to on next PPS +#define UE_REG_TIME64_FLAGS UE_REG_SR_ADDR(30) // flags - see chart above +#define UE_REG_TIME64_IMM UE_REG_SR_ADDR(31) // set immediate (0=latch on next pps, 1=latch immediate, default=0) +#define UE_REG_TIME64_TPS UE_REG_SR_ADDR(31) // clock ticks per second (counter rollover) + +//pps flags (see above) +#define UE_FLAG_TIME64_PPS_NEGEDGE (0 << 0) +#define UE_FLAG_TIME64_PPS_POSEDGE (1 << 0) +#define UE_FLAG_TIME64_PPS_SMA (0 << 1) +#define UE_FLAG_TIME64_PPS_MIMO (1 << 1) + +#define UE_FLAG_TIME64_LATCH_NOW 1 +#define UE_FLAG_TIME64_LATCH_NEXT_PPS 0 + +#endif + |