diff options
Diffstat (limited to 'host/tests')
| -rw-r--r-- | host/tests/rfnoc_block_tests/ddc_block_test.cpp | 24 |
1 files changed, 19 insertions, 5 deletions
diff --git a/host/tests/rfnoc_block_tests/ddc_block_test.cpp b/host/tests/rfnoc_block_tests/ddc_block_test.cpp index d32dd0aec..3656620f9 100644 --- a/host/tests/rfnoc_block_tests/ddc_block_test.cpp +++ b/host/tests/rfnoc_block_tests/ddc_block_test.cpp @@ -36,6 +36,7 @@ BOOST_AUTO_TEST_CASE(test_ddc_block) constexpr size_t num_chans = 4; constexpr noc_id_t noc_id = DDC_BLOCK; constexpr int TEST_DECIM = 20; + constexpr double DEFAULT_RATE = 200e6; // Matches typical MCR of X310 auto block_container = get_mock_block(noc_id, num_chans, num_chans, uhd::device_addr_t("foo=bar")); @@ -74,17 +75,24 @@ BOOST_AUTO_TEST_CASE(test_ddc_block) mock_source_term.set_edge_property<double>( "scaling", 1.0, {res_source_info::OUTPUT_EDGE, 0}); mock_source_term.set_edge_property<double>( - "samp_rate", 1.0, {res_source_info::OUTPUT_EDGE, 0}); + "samp_rate", DEFAULT_RATE, {res_source_info::OUTPUT_EDGE, 0}); constexpr size_t NEW_MTU = 4000; mock_source_term.set_edge_property<size_t>( "mtu", NEW_MTU, {res_source_info::OUTPUT_EDGE, 0}); +#define CHECK_INPUT_RATE(req_rate) \ + BOOST_REQUIRE_CLOSE(mock_source_term.get_edge_property<double>( \ + "samp_rate", {res_source_info::OUTPUT_EDGE, 0}), \ + req_rate, \ + 1e-6); + UHD_LOG_INFO("TEST", "Creating graph..."); graph.connect(&mock_source_term, test_ddc.get(), edge_info); graph.connect(test_ddc.get(), &mock_sink_term, edge_info); UHD_LOG_INFO("TEST", "Committing graph..."); graph.commit(); UHD_LOG_INFO("TEST", "Commit complete."); + CHECK_INPUT_RATE(DEFAULT_RATE); // We need to set the decimation again, because the rates will screw it // change it w.r.t. to the previous setting test_ddc->set_property<int>("decim", TEST_DECIM, 0); @@ -94,20 +102,26 @@ BOOST_AUTO_TEST_CASE(test_ddc_block) == mock_sink_term.get_edge_property<double>( "samp_rate", {res_source_info::INPUT_EDGE, 0}) * TEST_DECIM); + // Input rate should remain unchanged + CHECK_INPUT_RATE(DEFAULT_RATE); BOOST_CHECK(mock_sink_term.get_edge_property<double>( "scaling", {res_source_info::INPUT_EDGE, 0}) != 1.0); - UHD_LOG_INFO("TEST", "Setting freq to 1/8 of input rate"); - constexpr double TEST_FREQ = 1.0 / 8; + BOOST_CHECK_CLOSE(test_ddc->get_frequency_range(0).start(), -DEFAULT_RATE / 2, 1e-6); + BOOST_CHECK_CLOSE(test_ddc->get_frequency_range(0).stop(), DEFAULT_RATE / 2, 1e-6); + UHD_LOG_INFO("TEST", + "Setting freq to 1/8 of input rate (to " << (DEFAULT_RATE / 8) / 1e6 << " MHz)"); + constexpr double TEST_FREQ = DEFAULT_RATE / 8; test_ddc->set_property<double>("freq", TEST_FREQ, 0); const uint32_t freq_word_1 = ddc_reg_iface->write_memory.at(ddc_block_control::SR_FREQ_ADDR); BOOST_REQUIRE(freq_word_1 != 0); - UHD_LOG_INFO("TEST", "Doubling input rate (to 2.0)"); + UHD_LOG_INFO( + "TEST", "Doubling input rate (to " << (DEFAULT_RATE / 4) / 1e6 << " MHz)"); // Now this should change the freq word, but not the absolute frequency mock_source_term.set_edge_property<double>( - "samp_rate", 2.0, {res_source_info::OUTPUT_EDGE, 0}); + "samp_rate", DEFAULT_RATE * 2, {res_source_info::OUTPUT_EDGE, 0}); const double freq_word_2 = ddc_reg_iface->write_memory.at(ddc_block_control::SR_FREQ_ADDR); // The frequency word is the phase increment, which will halve. We skirt |