diff options
Diffstat (limited to 'host/lib/usrp/usrp2/usrp2_regs.hpp')
| -rw-r--r-- | host/lib/usrp/usrp2/usrp2_regs.hpp | 161 |
1 files changed, 86 insertions, 75 deletions
diff --git a/host/lib/usrp/usrp2/usrp2_regs.hpp b/host/lib/usrp/usrp2/usrp2_regs.hpp index 1a5864c85..0ebce6a85 100644 --- a/host/lib/usrp/usrp2/usrp2_regs.hpp +++ b/host/lib/usrp/usrp2/usrp2_regs.hpp @@ -18,6 +18,88 @@ #ifndef INCLUDED_USRP2_REGS_HPP #define INCLUDED_USRP2_REGS_HPP +//these are used to set the + +#define USRP2_MISC_OUTPUT_BASE 0xD400 +#define USRP2_GPIO_BASE 0xC800 +#define USRP2_ATR_BASE 0xE400 +#define USRP2_BP_STATUS_BASE 0xCC00 + +#define USRP2P_MISC_OUTPUT_BASE 0x2000 +#define USRP2P_GPIO_BASE 0x3200 +#define USRP2P_ATR_BASE 0x3800 +#define USRP2P_BP_STATUS_BASE 0x3300 + +#define USRP2P_FIRST_HW_REV 0x0A00 + +typedef struct { + int sr_misc; + int sr_tx_prot_eng; + int sr_rx_prot_eng; + int sr_buffer_pool_ctrl; + int sr_udp_sm; + int sr_tx_dsp; + int sr_tx_ctrl; + int sr_rx_dsp; + int sr_rx_ctrl; + int sr_time64; + int sr_simtimer; + int sr_last; + int misc_ctrl_clock; + int misc_ctrl_serdes; + int misc_ctrl_adc; + int misc_ctrl_leds; + int misc_ctrl_phy; + int misc_ctrl_dbg_mux; + int misc_ctrl_ram_page; + int misc_ctrl_flush_icache; + int misc_ctrl_led_src; + int time64_secs; // value to set absolute secs to on next PPS + int time64_ticks; // value to set absolute ticks to on next PPS + int time64_flags; // flags -- see chart below + int time64_imm; // set immediate (0=latch on next pps, 1=latch immediate, default=0) + int time64_tps; // ticks per second rollover count + int time64_secs_rb; + int time64_ticks_rb; + int dsp_tx_freq; + int dsp_tx_scale_iq; + int dsp_tx_interp_rate; + int dsp_tx_mux; + int dsp_rx_freq; + int dsp_rx_scale_iq; + int dsp_rx_decim_rate; + int dsp_rx_dcoffset_i; + int dsp_rx_dcoffset_q; + int dsp_rx_mux; + int gpio_base; + int gpio_io; + int gpio_ddr; + int gpio_tx_sel; + int gpio_rx_sel; + int atr_base; + int atr_idle_txside; + int atr_idle_rxside; + int atr_intx_txside; + int atr_intx_rxside; + int atr_inrx_txside; + int atr_inrx_rxside; + int atr_full_txside; + int atr_full_rxside; + int rx_ctrl_stream_cmd; + int rx_ctrl_time_secs; + int rx_ctrl_time_ticks; + int rx_ctrl_clear_overrun; + int rx_ctrl_vrt_header; + int rx_ctrl_vrt_stream_id; + int rx_ctrl_vrt_trailer; + int rx_ctrl_nsamps_per_pkt; + int rx_ctrl_nchannels; +} usrp2_regs_t; + +extern const usrp2_regs_t usrp2_regs; //the register definitions, set in usrp2_regs.cpp and usrp2p_regs.cpp + +usrp2_regs_t usrp2_get_regs(int hw_rev); + //////////////////////////////////////////////////// // Settings Bus, Slave #7, Not Byte Addressable! // @@ -25,27 +107,12 @@ // 1KB of address space (== 256 32-bit write-only regs) -#define MISC_OUTPUT_BASE 0xD400 +//#define MISC_OUTPUT_BASE 0xD400 //#define TX_PROTOCOL_ENGINE_BASE 0xD480 //#define RX_PROTOCOL_ENGINE_BASE 0xD4C0 //#define BUFFER_POOL_CTRL_BASE 0xD500 //#define LAST_SETTING_REG 0xD7FC // last valid setting register -#define SR_MISC 0 -#define SR_TX_PROT_ENG 32 -#define SR_RX_PROT_ENG 48 -#define SR_BUFFER_POOL_CTRL 64 -#define SR_UDP_SM 96 -#define SR_TX_DSP 208 -#define SR_TX_CTRL 224 -#define SR_RX_DSP 160 -#define SR_RX_CTRL 176 -#define SR_TIME64 192 -#define SR_SIMTIMER 198 -#define SR_LAST 255 - -#define _SR_ADDR(sr) ((MISC_OUTPUT_BASE) + (4*(sr))) - ///////////////////////////////////////////////// // SPI Slave Constants //////////////////////////////////////////////// @@ -58,20 +125,11 @@ #define SPI_SS_TX_DAC 32 #define SPI_SS_TX_ADC 64 #define SPI_SS_TX_DB 128 +#define SPI_SS_ADS62P44 256 //for usrp2p ///////////////////////////////////////////////// // Misc Control //////////////////////////////////////////////// -#define U2_REG_MISC_CTRL_CLOCK _SR_ADDR(0) -#define U2_REG_MISC_CTRL_SERDES _SR_ADDR(1) -#define U2_REG_MISC_CTRL_ADC _SR_ADDR(2) -#define U2_REG_MISC_CTRL_LEDS _SR_ADDR(3) -#define U2_REG_MISC_CTRL_PHY _SR_ADDR(4) // LSB is reset line to eth phy -#define U2_REG_MISC_CTRL_DBG_MUX _SR_ADDR(5) -#define U2_REG_MISC_CTRL_RAM_PAGE _SR_ADDR(6) // FIXME should go somewhere else... -#define U2_REG_MISC_CTRL_FLUSH_ICACHE _SR_ADDR(7) // Flush the icache -#define U2_REG_MISC_CTRL_LED_SRC _SR_ADDR(8) // HW or SW control for LEDs - #define U2_FLAG_MISC_CTRL_SERDES_ENABLE 8 #define U2_FLAG_MISC_CTRL_SERDES_PRBSEN 4 #define U2_FLAG_MISC_CTRL_SERDES_LOOPEN 2 @@ -99,14 +157,6 @@ * * </pre> */ -#define U2_REG_TIME64_SECS _SR_ADDR(SR_TIME64 + 0) // value to set absolute secs to on next PPS -#define U2_REG_TIME64_TICKS _SR_ADDR(SR_TIME64 + 1) // value to set absolute ticks to on next PPS -#define U2_REG_TIME64_FLAGS _SR_ADDR(SR_TIME64 + 2) // flags - see chart above -#define U2_REG_TIME64_IMM _SR_ADDR(SR_TIME64 + 3) // set immediate (0=latch on next pps, 1=latch immediate, default=0) -#define U2_REG_TIME64_TPS _SR_ADDR(SR_TIME64 + 4) // the ticks per second rollover count - -#define U2_REG_TIME64_SECS_RB (0xCC00 + 4*10) -#define U2_REG_TIME64_TICKS_RB (0xCC00 + 4*11) //pps flags (see above) #define U2_FLAG_TIME64_PPS_NEGEDGE (0 << 0) @@ -120,9 +170,6 @@ ///////////////////////////////////////////////// // DSP TX Regs //////////////////////////////////////////////// -#define U2_REG_DSP_TX_FREQ _SR_ADDR(SR_TX_DSP + 0) -#define U2_REG_DSP_TX_SCALE_IQ _SR_ADDR(SR_TX_DSP + 1) // {scale_i,scale_q} -#define U2_REG_DSP_TX_INTERP_RATE _SR_ADDR(SR_TX_DSP + 2) /*! * \brief output mux configuration. @@ -158,17 +205,11 @@ * The default value is 0x10 * </pre> */ -#define U2_REG_DSP_TX_MUX _SR_ADDR(SR_TX_DSP + 4) ///////////////////////////////////////////////// // DSP RX Regs //////////////////////////////////////////////// -#define U2_REG_DSP_RX_FREQ _SR_ADDR(SR_RX_DSP + 0) -#define U2_REG_DSP_RX_SCALE_IQ _SR_ADDR(SR_RX_DSP + 1) // {scale_i,scale_q} -#define U2_REG_DSP_RX_DECIM_RATE _SR_ADDR(SR_RX_DSP + 2) -#define U2_REG_DSP_RX_DCOFFSET_I _SR_ADDR(SR_RX_DSP + 3) // Bit 31 high sets fixed offset mode, using lower 14 bits, - // otherwise it is automatic -#define U2_REG_DSP_RX_DCOFFSET_Q _SR_ADDR(SR_RX_DSP + 4) // Bit 31 high sets fixed offset mode, using lower 14 bits + /*! * \brief input mux configuration. * @@ -190,20 +231,10 @@ * The default value is 0x4 * </pre> */ -#define U2_REG_DSP_RX_MUX _SR_ADDR(SR_RX_DSP + 5) // called adc_mux in dsp_core_rx.v //////////////////////////////////////////////// // GPIO, Slave 4 //////////////////////////////////////////////// -// -// These go to the daughterboard i/o pins -// -#define U2_REG_GPIO_BASE 0xC800 - -#define U2_REG_GPIO_IO U2_REG_GPIO_BASE + 0 // 32 bits, gpio io pins (tx high 16 bits, rx low 16 bits) -#define U2_REG_GPIO_DDR U2_REG_GPIO_BASE + 4 // 32 bits, gpio ddr, 1 means output (tx high 16 bits, rx low 16 bits) -#define U2_REG_GPIO_TX_SEL U2_REG_GPIO_BASE + 8 // 16 2-bit fields select which source goes to TX DB -#define U2_REG_GPIO_RX_SEL U2_REG_GPIO_BASE + 12 // 16 2-bit fields select which source goes to RX DB // each 2-bit sel field is layed out this way #define U2_FLAG_GPIO_SEL_GPIO 0 // if pin is an output, set by GPIO register @@ -214,31 +245,11 @@ /////////////////////////////////////////////////// // ATR Controller, Slave 11 //////////////////////////////////////////////// -#define U2_REG_ATR_BASE 0xE400 -#define U2_REG_ATR_IDLE_TXSIDE U2_REG_ATR_BASE + 0 -#define U2_REG_ATR_IDLE_RXSIDE U2_REG_ATR_BASE + 2 -#define U2_REG_ATR_INTX_TXSIDE U2_REG_ATR_BASE + 4 -#define U2_REG_ATR_INTX_RXSIDE U2_REG_ATR_BASE + 6 -#define U2_REG_ATR_INRX_TXSIDE U2_REG_ATR_BASE + 8 -#define U2_REG_ATR_INRX_RXSIDE U2_REG_ATR_BASE + 10 -#define U2_REG_ATR_FULL_TXSIDE U2_REG_ATR_BASE + 12 -#define U2_REG_ATR_FULL_RXSIDE U2_REG_ATR_BASE + 14 /////////////////////////////////////////////////// // VITA RX CTRL regs /////////////////////////////////////////////////// -// The following 3 are logically a single command register. -// They are clocked into the underlying fifo when time_ticks is written. -#define U2_REG_RX_CTRL_STREAM_CMD _SR_ADDR(SR_RX_CTRL + 0) // {now, chain, num_samples(30) -#define U2_REG_RX_CTRL_TIME_SECS _SR_ADDR(SR_RX_CTRL + 1) -#define U2_REG_RX_CTRL_TIME_TICKS _SR_ADDR(SR_RX_CTRL + 2) - -#define U2_REG_RX_CTRL_CLEAR_OVERRUN _SR_ADDR(SR_RX_CTRL + 3) // write anything to clear overrun -#define U2_REG_RX_CTRL_VRT_HEADER _SR_ADDR(SR_RX_CTRL + 4) // word 0 of packet. FPGA fills in packet counter -#define U2_REG_RX_CTRL_VRT_STREAM_ID _SR_ADDR(SR_RX_CTRL + 5) // word 1 of packet. -#define U2_REG_RX_CTRL_VRT_TRAILER _SR_ADDR(SR_RX_CTRL + 6) -#define U2_REG_RX_CTRL_NSAMPS_PER_PKT _SR_ADDR(SR_RX_CTRL + 7) -#define U2_REG_RX_CTRL_NCHANNELS _SR_ADDR(SR_RX_CTRL + 8) // 1 in basic case, up to 4 for vector sources + #endif /* INCLUDED_USRP2_REGS_HPP */ |