2 files changed, 58 insertions, 4 deletions
diff --git a/host/docs/dboards.rst b/host/docs/dboards.rst
index 9c496ebee..b66fd2069 100644
--- a/host/docs/dboards.rst
+++ b/host/docs/dboards.rst
@@ -32,7 +32,20 @@ The Basic TX and LFTX boards have 1 quadrature subdevice using both antennas.
 
 The boards have no tunable elements or programmable gains.
 Though the magic of aliasing, you can up-convert signals
-greater than the nyquist rate of the DAC.
+greater than the Nyquist rate of the DAC.
+
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+DBSRX
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+The DBSRX board has 1 quadrature subdevice.
+
+Receive Antennas: **J3**
+
+The board has no user selectable antenna setting
+
+Recieve Gains: 
+    **GC1**, Range: 0-56dB
+    **GC2**, Range: 0-24dB
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
 RFX Series
@@ -45,7 +58,7 @@ The user may set the receive antenna to be TX/RX or RX2.
 However, when using an RFX board in full-duplex mode,
 the receive antenna will always be set to RX2, regardless of the settings.
 
-Recieve Gains: **PGA0**, Range: 0-45dB
+Recieve Gains: **PGA0**, Range: 0-70dB (except RFX400 range is 0-45dB)
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
 XCVR 2450
@@ -87,3 +100,44 @@ the receive antenna will always be set to RX2, regardless of the settings.
 Transmit Gains: **PGA0**, Range: 0-25dB
 
 Recieve Gains: **PGA0**, Range: 0-31.5dB
+
+------------------------------------------------------------------------
+Daughterboard Modifications
+------------------------------------------------------------------------
+
+Sometimes, daughterboards will require modification
+to work on certain frequencies or to work with certain hardware.
+Modification usually involves moving/removing a SMT component
+and burning a new daughterboard id into the eeprom.
+
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+DBSRX
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+Due to different clocking capabilities,
+the DBSRX will require modifications to operate on a non-USRP1 motherboard.
+On a USRP1 motherboard, a divided clock is provided from an FPGA pin
+because the standard daughterboard clock lines cannot provided a divided clock.
+However, on other USRP motherboards, the divided clock is provided
+over the standard daughterboard clock lines.
+
+**Step 1: Move the clock configuration resistor**
+
+Remove R193 (which is 10 ohms, 0603 size) and put it on R194, which is empty.
+This is made somewhat more complicated by the fact that the silkscreen is not clear in that area.
+R193 is on the back, immediately below the large beige connector, J2.
+R194 is just below, and to the left of R193.
+The silkscreen for R193 is ok, but for R194,
+it is upside down, and partially cut off.
+If you lose R193, you can use anything from 0 to 10 ohms there.
+
+**Step 2: Burn a new daughterboard id into the EEPROM**
+
+With the daughterboard plugged-in, run the following commands:
+::
+
+    cd <prefix>/share/uhd/utils
+    ./usrp_burn_db_eeprom --id=0x000d --unit=RX --args=<args> --db=<db>
+
+* <args> are device address arguments (optional if only one USRP is on your machine)
+* <db> is the name of the daughterboard slot (optional if the USRP has only one slot)
diff --git a/host/docs/usrp2.rst b/host/docs/usrp2.rst
index 76b27fd31..bc4ea0e44 100644
--- a/host/docs/usrp2.rst
+++ b/host/docs/usrp2.rst
@@ -38,7 +38,7 @@ Run the following commands:
     ./configure --host=mb
     make
 
-*The image file will be ./apps/txrx_uhd.bin*
+*The image file will be ./usrp2/usrp2_txrx_uhd.bin*
 
 ------------------------------------------------------------------------
 Load the images onto the SD card
@@ -161,7 +161,7 @@ The USRP2 will reply to icmp echo requests.
 **Monitor the USRP2:**
 You can read the serial port on the rear of the USRP2
 to get debug verbose from the embedded microcontroller.
-Use a standard USB to tty-level serial converter at 230400 baud.
+Use a standard USB to 3.3v-level serial converter at 230400 baud.
 The microcontroller prints useful information about IP addresses,
 MAC addresses, control packets, and fast-path settings.