3 files changed, 58 insertions, 7 deletions
diff --git a/host/docs/dboards.rst b/host/docs/dboards.rst
index 373189441..42965b32f 100644
--- a/host/docs/dboards.rst
+++ b/host/docs/dboards.rst
@@ -130,6 +130,7 @@ Bandwidths (Hz):
 Sensors:
 
 * **lo_locked**: boolean for LO lock state
+* **rssi**:      float for rssi in dBm
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
 XCVR 2450
@@ -204,6 +205,45 @@ Sensors:
 * **lo_locked**: boolean for LO lock state
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
+SBX Series
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
+The SBX Series boards have 2 quadrature subdevices, one transmit, one receive.
+Transmit and Receive default to direct conversion but
+can be used in low IF mode through lo_offset in uhd::tune_request_t
+
+The SBX Series boards have independent receive and transmit LO's and synthesizers 
+allowing full-duplex operation on different transmit and receive frequencies.
+
+Transmit Antennas: **TX/RX**
+
+Receive Antennas: **TX/RX** or **RX2**
+
+The user may set the receive antenna to be TX/RX or RX2.
+However, when using an SBX board in full-duplex mode,
+the receive antenna will always be set to RX2, regardless of the settings.
+
+Transmit Gains: **PGA0**, Range: 0-31.5dB
+
+Receive Gains: **PGA0**, Range: 0-31.5dB
+
+Bandwidths (Hz):
+
+* **RX**: 40M
+* **TX**: 40M
+
+Sensors:
+
+* **lo_locked**: boolean for LO lock state
+
+LEDs:
+
+* All LEDs flash when dboard control is initialized
+* **TX LD**: Transmit Synthesizer Lock Detect
+* **TX/RX**: Receiver on TX/RX antenna port (No TX)
+* **RX LD**: Receive Synthesizer Lock Detect
+* **RX1/RX2**: Receiver on RX2 antenna port
+
+^^^^^^^^^^^^^^^^^^^^^^^^^^^
 TVRX
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
 The TVRX board has 1 real-mode subdevice.
diff --git a/host/docs/usrp1.rst b/host/docs/usrp1.rst
index f77a26e0a..97a8c3bb5 100644
--- a/host/docs/usrp1.rst
+++ b/host/docs/usrp1.rst
@@ -136,6 +136,11 @@ The USRP can be modified to accept an external clock reference instead of the 64
 
 The new external clock needs to be a square wave between +7dBm and +15dBm
 
-For the correct clock settings, call usrp->set_master_clock_rate(EXT_CLOCK_FREQUENCY)
-before any other parameters are set in your application.
+After the hardware modification,
+the user should burn the setting into the EEPROM,
+so UHD can initialize with the correct clock rate.
+Run the following commands to record the setting into the EEPROM:
+::
 
+    cd <install-path>/share/uhd/utils
+    ./usrp_burn_mb_eeprom --args=<optional device args> --key=mcr --val=<rate>
diff --git a/host/docs/usrp_e1xx.rst b/host/docs/usrp_e1xx.rst
index 2818a0a65..036d2c02c 100644
--- a/host/docs/usrp_e1xx.rst
+++ b/host/docs/usrp_e1xx.rst
@@ -20,7 +20,6 @@ Example device address string representations to specify non-standard FPGA image
 Changing the master clock rate
 ------------------------------------------------------------------------
 The master clock rate of the USRP embedded feeds both the FPGA DSP and the codec chip.
-UHD can dynamically reconfigure the clock rate though the set_master_clock_rate() API call.
 Hundreds of rates between 32MHz and 64MHz are available.
 A few notable rates are:
 
@@ -36,8 +35,12 @@ To use the 61.44MHz clock rate, the USRP embedded will require two jumpers to be
 * J16 is a two pin header, remove the jumper (or leave it on pin1 only)
 * J15 is a three pin header, move the jumper to (pin1, pin2)
 
-For the correct clock settings, call usrp->set_master_clock_rate(61.44e6)
-before any other parameters are set in your application.
+Then run the following commands to record the setting into the EEPROM:
+::
+
+    cd <install-path>/share/uhd/utils
+    ./usrp_burn_mb_eeprom --key=mcr --val=61.44e6
+
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 Set other rates - uses internal VCO
@@ -47,8 +50,11 @@ To use other clock rates, the jumpers will need to be in the default position.
 * J16 is a two pin header, move the jumper to (pin1, pin2)
 * J15 is a three pin header, move the jumper to (pin2, pin3)
 
-For the correct clock settings, call usrp->set_master_clock_rate(rate)
-before any other parameters are set in your application.
+Then run the following commands to record the setting into the EEPROM:
+::
+
+    cd <install-path>/share/uhd/utils
+    ./usrp_burn_mb_eeprom --key=mcr --val=<rate>
 
 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
 Clock rate recovery - unbricking