diff options
Diffstat (limited to 'host/docs/dboards.rst')
| -rw-r--r-- | host/docs/dboards.rst | 382 |
1 files changed, 382 insertions, 0 deletions
diff --git a/host/docs/dboards.rst b/host/docs/dboards.rst new file mode 100644 index 000000000..218498dd2 --- /dev/null +++ b/host/docs/dboards.rst @@ -0,0 +1,382 @@ +======================================================================== +UHD - Daughterboard Application Notes +======================================================================== + +.. contents:: Table of Contents + +------------------------------------------------------------------------ +Daughterboard Properties +------------------------------------------------------------------------ + +The following contains interesting notes about each daughterboard. +Eventually, this page will be expanded to list out the full +properties of each board as well. + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +Basic RX and and LFRX +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The Basic RX and LFRX boards have 4 frontends: + +* **Frontend A:** real signal on antenna RXA +* **Frontend B:** real signal on antenna RXB +* **Frontend AB:** quadrature frontend using both antennas (IQ) +* **Frontend BA:** quadrature frontend using both antennas (QI) + +The boards have no tunable elements or programmable gains. +Though the magic of aliasing, you can down-convert signals +greater than the Nyquist rate of the ADC. + +BasicRX Bandwidth (Hz): + +* For Real-Mode (A or B frontend): 250M +* For Complex (AB or BA frontend): 500M + +LFRX Bandwidth (Hz): + +* For Real-Mode (A or B frontend): 33M +* For Complex (AB or BA frontend): 66M + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +Basic TX and and LFTX +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The Basic TX and LFTX boards have 4 frontends: + +* **Frontend A:** real signal on antenna TXA +* **Frontend B:** real signal on antenna TXB +* **Frontend AB:** quadrature frontend using both antennas (IQ) +* **Frontend BA:** quadrature frontend using both antennas (QI) + +The boards have no tunable elements or programmable gains. +Though the magic of aliasing, you can up-convert signals +greater than the Nyquist rate of the DAC. + +BasicTX Bandwidth (Hz): 250M + +* For Real-Mode (A or B frontend): 250M +* For Complex (AB or BA frontend): 500M + +LFTX Bandwidth (Hz): 33M + +* For Real-Mode (A or B frontend): 33M +* For Complex (AB or BA frontend): 66M + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +DBSRX +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The DBSRX board has 1 quadrature frontend. +It defaults to direct conversion, but can use a low IF through lo_offset in uhd::tune_request_t + +Receive Antennas: **J3** + +* **Frontend 0:** Complex baseband signal from antenna J3 + +The board has no user selectable antenna setting + +Receive Gains: + +* **GC1**, Range: 0-56dB +* **GC2**, Range: 0-24dB + +Bandwidth (Hz): 8M-66M + +Sensors: + +* **lo_locked**: boolean for LO lock state + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +DBSRX2 +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The DBSRX2 board has 1 quadrature frontend. +It defaults to direct conversion, but can use a low IF through lo_offset in uhd::tune_request_t + +Receive Antennas: **J3** + +* **Frontend 0:** Complex baseband signal from antenna J3 + +The board has no user selectable antenna setting + +Receive Gains: + +* **GC1**, Range: 0-73dB +* **BBG**, Range: 0-15dB + +Bandwidth (Hz): 8M-80M + +Sensors: + +* **lo_locked**: boolean for LO lock state + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +RFX Series +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The RFX Series boards have 2 quadrature frontends, one transmit, one receive. +Transmit defaults to low IF and Receive defaults to direct conversion. +The IF can be adjusted through lo_offset in uhd::tune_request_t + +The RFX Series boards have independent receive and transmit LO's and synthesizers +allowing full-duplex operation on different transmit and receive frequencies. + +Transmit Antennas: **TX/RX** + +Receive Antennas: **TX/RX** or **RX2** + +* **Frontend 0:** Complex baseband signal for selected antenna + +The user may set the receive antenna to be TX/RX or RX2. +However, when using an RFX board in full-duplex mode, +the receive antenna will always be set to RX2, regardless of the settings. + +Receive Gains: **PGA0**, Range: 0-70dB (except RFX400 range is 0-45dB) + +Bandwidths (Hz): + +* **RX**: 40M +* **TX**: 40M + +Sensors: + +* **lo_locked**: boolean for LO lock state +* **rssi**: float for rssi in dBm + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +XCVR 2450 +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The XCVR2450 has 2 quadrature frontends, one transmit, one receive. +Transmit and Receive default to direct conversion but +can be used in low IF mode through lo_offset in uhd::tune_request_t + +The XCVR2450 has a non-contiguous tuning range consisting of a +high band (4.9-6.0GHz) and a low band (2.4-2.5GHz). + +Transmit Antennas: **J1** or **J2** + +Receive Antennas: **J1** or **J2** + +* **Frontend 0:** Complex baseband signal for selected antenna + +The XCVR2450 uses a common LO for both receive and transmit. +Even though the API allows the RX and TX LOs to be individually set, +a change of one LO setting will be reflected in the other LO setting. + +The XCVR2450 does not support full-duplex mode, attempting to operate +in full-duplex will result in transmit-only operation. + +Transmit Gains: + +* **VGA**, Range: 0-30dB +* **BB**, Range: 0-5dB + +Receive Gains: + +* **LNA**, Range: 0-30.5dB +* **VGA**, Range: 0-62dB + +Bandwidths (Hz): + +* **RX**: 15M, 19M, 28M, 36M; (each +-0, 5, or 10%) +* **TX**: 24M, 36M, 48M + +Sensors: + +* **lo_locked**: boolean for LO lock state +* **rssi**: float for rssi in dBm + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +WBX Series +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The WBX Series boards have 2 quadrature frontends, one transmit, one receive. +Transmit and Receive default to direct conversion but +can be used in low IF mode through lo_offset in uhd::tune_request_t + +The WBX Series boards have independent receive and transmit LO's and synthesizers +allowing full-duplex operation on different transmit and receive frequencies. + +Transmit Antennas: **TX/RX** + +Receive Antennas: **TX/RX** or **RX2** + +* **Frontend 0:** Complex baseband signal for selected antenna + +The user may set the receive antenna to be TX/RX or RX2. +However, when using an WBX board in full-duplex mode, +the receive antenna will always be set to RX2, regardless of the settings. + +Transmit Gains: **PGA0**, Range: 0-25dB + +Receive Gains: **PGA0**, Range: 0-31.5dB + +Bandwidths (Hz): + +* **RX**: 40M +* **TX**: 40M + +Sensors: + +* **lo_locked**: boolean for LO lock state + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +SBX Series +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The SBX Series boards have 2 quadrature frontends, one transmit, one receive. +Transmit and Receive default to direct conversion but +can be used in low IF mode through lo_offset in uhd::tune_request_t + +The SBX Series boards have independent receive and transmit LO's and synthesizers +allowing full-duplex operation on different transmit and receive frequencies. + +Transmit Antennas: **TX/RX** + +Receive Antennas: **TX/RX** or **RX2** + +* **Frontend 0:** Complex baseband signal for selected antenna + +The user may set the receive antenna to be TX/RX or RX2. +However, when using an SBX board in full-duplex mode, +the receive antenna will always be set to RX2, regardless of the settings. + +Transmit Gains: **PGA0**, Range: 0-31.5dB + +Receive Gains: **PGA0**, Range: 0-31.5dB + +Bandwidths (Hz): + +* **RX**: 40M +* **TX**: 40M + +Sensors: + +* **lo_locked**: boolean for LO lock state + +LEDs: + +* All LEDs flash when dboard control is initialized +* **TX LD**: Transmit Synthesizer Lock Detect +* **TX/RX**: Receiver on TX/RX antenna port (No TX) +* **RX LD**: Receive Synthesizer Lock Detect +* **RX1/RX2**: Receiver on RX2 antenna port + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +TVRX +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The TVRX board has 1 real-mode frontend. +It is operated at a low IF. + +Receive Antennas: RX + +* **Frontend 0:** real-mode baseband signal from antenna RX + +Receive Gains: + +* **RF**, Range: -13.3-50.3dB (frequency-dependent) +* **IF**, Range: -1.5-32.5dB + +Bandwidth: 6MHz + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +TVRX2 +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +The TVRX2 board has 2 real-mode frontends. +It is operated at a low IF. + +Receive Frontends: + +* **Frontend RX1:** real-mode baseband from antenna J100 +* **Frontend RX2:** real-mode baseband from antenna J140 + +Note: The TVRX2 has always-on AGC, the software controllable gain is the +final gain stage which controls the AGC set-point for output to ADC. + +Receive Gains: + +* **IF**, Range: 0.0-30.0dB + +Bandwidth: 1.7MHz, 6MHz, 7MHz, 8MHz, 10MHz + +Sensors: + +* **lo_locked**: boolean for LO lock state +* **rssi**: float for measured RSSI in dBm +* **temperature**: float for measured temperature in degC + +------------------------------------------------------------------------ +Daughterboard Modifications +------------------------------------------------------------------------ + +Sometimes, daughterboards will require modification +to work on certain frequencies or to work with certain hardware. +Modification usually involves moving/removing a SMT component +and burning a new daughterboard id into the eeprom. + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +DBSRX - Mod +^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Due to different clocking capabilities, +the DBSRX will require modifications to operate on a non-USRP1 motherboard. +On a USRP1 motherboard, a divided clock is provided from an FPGA pin +because the standard daughterboard clock lines cannot provided a divided clock. +However, on other USRP motherboards, the divided clock is provided +over the standard daughterboard clock lines. + +**Step 1: Move the clock configuration resistor** + +Remove R193 (which is 10 ohms, 0603 size) and put it on R194, which is empty. +This is made somewhat more complicated by the fact that the silkscreen is not clear in that area. +R193 is on the back, immediately below the large beige connector, J2. +R194 is just below, and to the left of R193. +The silkscreen for R193 is ok, but for R194, +it is upside down, and partially cut off. +If you lose R193, you can use anything from 0 to 10 ohms there. + +**Step 2: Burn a new daughterboard id into the EEPROM** + +With the daughterboard plugged-in, run the following commands: +:: + + cd <install-path>/share/uhd/utils + ./usrp_burn_db_eeprom --id=0x000d --unit=RX --args=<args> --slot=<slot> + +* <args> are device address arguments (optional if only one USRP is on your machine) +* <slot> is the name of the daughterboard slot (optional if the USRP has only one slot) + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +RFX - Mod +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +Older RFX boards require modifications to use the motherboard oscillator. +If this is the case, UHD will print a warning about the modification. +Please follow the modification procedures below: + +**Step 1: Disable the daughterboard clocks** + +Move R64 to R84, Move R142 to R153 + +**Step 2: Connect the motherboard blocks** + +Move R35 to R36, Move R117 to R115 +These are all 0-ohm, so if you lose one, just short across the appropriate pads + +**Step 3: Burn the appropriate daughterboard id into the EEPROM** + +With the daughterboard plugged-in, run the following commands: +:: + + cd <install-path>/share/uhd/utils + ./usrp_burn_db_eeprom --id=<rx_id> --unit=RX --args=<args> --slot=<slot> + ./usrp_burn_db_eeprom --id=<tx_id> --unit=TX --args=<args> --slot=<slot> + +* <rx_id> choose the appropriate RX ID for your daughterboard + + * **RFX400:** 0x0024 + * **RFX900:** 0x0025 + * **RFX1800:** 0x0034 + * **RFX1200:** 0x0026 + * **RFX2400:** 0x0027 +* <tx_id> choose the appropriate TX ID for your daughterboard + + * **RFX400:** 0x0028 + * **RFX900:** 0x0029 + * **RFX1800:** 0x0035 + * **RFX1200:** 0x002a + * **RFX2400:** 0x002b +* <args> are device address arguments (optional if only one USRP is on your machine) +* <slot> is the name of the daughterboard slot (optional if the USRP has only one slot) |