diff options
Diffstat (limited to 'host/docs/dboards.rst')
| -rw-r--r-- | host/docs/dboards.rst | 80 |
1 files changed, 71 insertions, 9 deletions
diff --git a/host/docs/dboards.rst b/host/docs/dboards.rst index 080117651..7f205c404 100644 --- a/host/docs/dboards.rst +++ b/host/docs/dboards.rst @@ -26,6 +26,14 @@ The boards have no tunable elements or programmable gains. Though the magic of aliasing, you can down-convert signals greater than the Nyquist rate of the ADC. +BasicRX Bandwidth (Hz): + For Real-Mode (A or B subdevice): 250M + For Complex (AB or BA subdevice): 500M + +LFRX Bandwidth (Hz): + For Real-Mode (A or B subdevice): 33M + For Complex (AB or BA subdevice): 66M + ^^^^^^^^^^^^^^^^^^^^^^^^^^^ Basic TX and and LFTX ^^^^^^^^^^^^^^^^^^^^^^^^^^^ @@ -40,6 +48,14 @@ The boards have no tunable elements or programmable gains. Though the magic of aliasing, you can up-convert signals greater than the Nyquist rate of the DAC. +BasicTX Bandwidth (Hz): 250M + For Real-Mode (A or B subdevice): 250M + For Complex (AB or BA subdevice): 500M + +LFTX Bandwidth (Hz): 33M + For Real-Mode (A or B subdevice): 33M + For Complex (AB or BA subdevice): 66M + ^^^^^^^^^^^^^^^^^^^^^^^^^^^ DBSRX ^^^^^^^^^^^^^^^^^^^^^^^^^^^ @@ -53,7 +69,7 @@ Receive Gains: **GC1**, Range: 0-56dB **GC2**, Range: 0-24dB -Low-Pass Filter Bandwidth (Hz): 4M-33M +Bandwidth (Hz): 8M-66M ^^^^^^^^^^^^^^^^^^^^^^^^^^^ RFX Series @@ -68,6 +84,10 @@ the receive antenna will always be set to RX2, regardless of the settings. Receive Gains: **PGA0**, Range: 0-70dB (except RFX400 range is 0-45dB) +Bandwidths (Hz): + * **RX**: 40M + * **TX**: 40M + ^^^^^^^^^^^^^^^^^^^^^^^^^^^ XCVR 2450 ^^^^^^^^^^^^^^^^^^^^^^^^^^^ @@ -93,9 +113,9 @@ Receive Gains: * **LNA**, Range: 0-30.5dB * **VGA**, Range: 0-62dB -Low-Pass Filter Bandwidths (Hz): - * **RX**: 7.5M, 9.5M, 14M, 18M; (each +-0, 5, or 10%) - * **TX**: 12M, 18M, 24M +Bandwidths (Hz): + * **RX**: 15M, 19M, 28M, 36M; (each +-0, 5, or 10%) + * **TX**: 24M, 36M, 48M ^^^^^^^^^^^^^^^^^^^^^^^^^^^ WBX Series @@ -112,9 +132,9 @@ Transmit Gains: **PGA0**, Range: 0-25dB Receive Gains: **PGA0**, Range: 0-31.5dB -Low-Pass Filter Bandwidths (Hz): - * **RX**: 20M (Fixed) - * **TX**: 20M (Fixed) +Bandwidths (Hz): + * **RX**: 40M + * **TX**: 40M ^^^^^^^^^^^^^^^^^^^^^^^^^^^ TVRX @@ -125,7 +145,7 @@ Receive Gains: * **RF**, Range: -13.3-50.3dB (frequency-dependent) * **IF**, Range: -1.5-32.5dB -Bandpass Filter Bandwidth: 6MHz +Bandwidth: 6MHz ------------------------------------------------------------------------ Daughterboard Modifications @@ -137,7 +157,7 @@ Modification usually involves moving/removing a SMT component and burning a new daughterboard id into the eeprom. ^^^^^^^^^^^^^^^^^^^^^^^^^^^ -DBSRX +DBSRX - Mod ^^^^^^^^^^^^^^^^^^^^^^^^^^^ Due to different clocking capabilities, @@ -167,3 +187,45 @@ With the daughterboard plugged-in, run the following commands: * <args> are device address arguments (optional if only one USRP is on your machine) * <slot> is the name of the daughterboard slot (optional if the USRP has only one slot) + +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +RFX - Mod +^^^^^^^^^^^^^^^^^^^^^^^^^^^ +Older RFX boards require modifications to use the motherboard oscillator. +If this is the case, UHD will print a warning about the modification. +Please follow the modification procedures below: + +**Step 1: Disable the daughterboard clocks** + +Move R64 to R84, Move R142 to R153 + +**Step 2: Connect the motherboard blocks** + +Move R35 to R36, Move R117 to R115 +These are all 0-ohm, so if you lose one, just short across the appropriate pads + +**Step 3: Burn the appropriate daughterboard id into the EEPROM** + +With the daughterboard plugged-in, run the following commands: +:: + + cd <prefix>/share/uhd/utils + ./usrp_burn_db_eeprom --id=<rx_id> --unit=RX --args=<args> --slot=<slot> + ./usrp_burn_db_eeprom --id=<tx_id> --unit=TX --args=<args> --slot=<slot> + +* <rx_id> choose the appropriate RX ID for your daughterboard + + * **RFX400:** 0x0024 + * **RFX900:** 0x0025 + * **RFX1800:** 0x0034 + * **RFX1200:** 0x0026 + * **RFX2400:** 0x0027 +* <tx_id> choose the appropriate TX ID for your daughterboard + + * **RFX400:** 0x0028 + * **RFX900:** 0x0029 + * **RFX1800:** 0x0035 + * **RFX1200:** 0x002a + * **RFX2400:** 0x002b +* <args> are device address arguments (optional if only one USRP is on your machine) +* <slot> is the name of the daughterboard slot (optional if the USRP has only one slot) |