diff options
Diffstat (limited to 'fpga/usrp2/gpmc/gpmc_async.v')
| -rw-r--r-- | fpga/usrp2/gpmc/gpmc_async.v | 245 |
1 files changed, 245 insertions, 0 deletions
diff --git a/fpga/usrp2/gpmc/gpmc_async.v b/fpga/usrp2/gpmc/gpmc_async.v new file mode 100644 index 000000000..c0bec683a --- /dev/null +++ b/fpga/usrp2/gpmc/gpmc_async.v @@ -0,0 +1,245 @@ +// +// Copyright 2011 Ettus Research LLC +// +// This program is free software: you can redistribute it and/or modify +// it under the terms of the GNU General Public License as published by +// the Free Software Foundation, either version 3 of the License, or +// (at your option) any later version. +// +// This program is distributed in the hope that it will be useful, +// but WITHOUT ANY WARRANTY; without even the implied warranty of +// MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +// GNU General Public License for more details. +// +// You should have received a copy of the GNU General Public License +// along with this program. If not, see <http://www.gnu.org/licenses/>. +// + +////////////////////////////////////////////////////////////////////////////////// + +module gpmc_async + #(parameter TXFIFOSIZE = 11, + parameter RXFIFOSIZE = 11, + parameter BUSDEBUG = 1) + (// GPMC signals + input arst, + input EM_CLK, inout [15:0] EM_D, input [10:1] EM_A, input [1:0] EM_NBE, + input EM_WAIT0, input EM_NCS4, input EM_NCS6, input EM_NWE, input EM_NOE, + + // GPIOs for FIFO signalling + output rx_have_data, output tx_have_space, output reg bus_error, input bus_reset, + + // Wishbone signals + input wb_clk, input wb_rst, + output [10:0] wb_adr_o, output [15:0] wb_dat_mosi, input [15:0] wb_dat_miso, + output [1:0] wb_sel_o, output wb_cyc_o, output wb_stb_o, output wb_we_o, input wb_ack_i, + + // FIFO interface + input fifo_clk, input fifo_rst, input clear_tx, input clear_rx, + output [35:0] tx_data_o, output tx_src_rdy_o, input tx_dst_rdy_i, + input [35:0] rx_data_i, input rx_src_rdy_i, output rx_dst_rdy_o, + + input [15:0] tx_frame_len, output [15:0] rx_frame_len, + + output tx_underrun, output rx_overrun, + input [7:0] test_rate, input [3:0] test_ctrl, + output [31:0] debug + ); + + wire EM_output_enable = (~EM_NOE & (~EM_NCS4 | ~EM_NCS6)); + wire [15:0] EM_D_fifo; + wire [15:0] EM_D_wb; + + assign EM_D = ~EM_output_enable ? 16'bz : ~EM_NCS4 ? EM_D_fifo : EM_D_wb; + + wire bus_error_tx, bus_error_rx; + + always @(posedge fifo_clk) + if(fifo_rst | clear_tx | clear_rx) + bus_error <= 0; + else + bus_error <= bus_error_tx | bus_error_rx; + + // CS4 is RAM_2PORT for DATA PATH (high-speed data) + // Writes go into one RAM, reads come from the other + // CS6 is for CONTROL PATH (wishbone) + + // //////////////////////////////////////////// + // TX Data Path + + wire [17:0] tx18_data, tx18b_data; + wire tx18_src_rdy, tx18_dst_rdy, tx18b_src_rdy, tx18b_dst_rdy; + wire [15:0] tx_fifo_space; + wire [35:0] tx36_data, tx_data; + wire tx36_src_rdy, tx36_dst_rdy, tx_src_rdy, tx_dst_rdy; + + gpmc_to_fifo_async gpmc_to_fifo_async + (.EM_D(EM_D), .EM_NBE(EM_NBE), .EM_NCS(EM_NCS4), .EM_NWE(EM_NWE), + .fifo_clk(fifo_clk), .fifo_rst(fifo_rst), .clear(clear_tx), + .data_o(tx18_data), .src_rdy_o(tx18_src_rdy), .dst_rdy_i(tx18_dst_rdy), + .frame_len(tx_frame_len), .fifo_space(tx_fifo_space), .fifo_ready(tx_have_space), + .bus_error(bus_error_tx) ); + + fifo_cascade #(.WIDTH(18), .SIZE(10)) tx_fifo + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .datain(tx18_data), .src_rdy_i(tx18_src_rdy), .dst_rdy_o(tx18_dst_rdy), .space(tx_fifo_space), + .dataout(tx18b_data), .src_rdy_o(tx18b_src_rdy), .dst_rdy_i(tx18b_dst_rdy), .occupied()); + + fifo19_to_fifo36 #(.LE(1)) f19_to_f36 // Little endian because ARM is LE + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .f19_datain({1'b0,tx18b_data}), .f19_src_rdy_i(tx18b_src_rdy), .f19_dst_rdy_o(tx18b_dst_rdy), + .f36_dataout(tx36_data), .f36_src_rdy_o(tx36_src_rdy), .f36_dst_rdy_i(tx36_dst_rdy)); + + fifo_cascade #(.WIDTH(36), .SIZE(TXFIFOSIZE)) tx_fifo36 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .datain(tx36_data), .src_rdy_i(tx36_src_rdy), .dst_rdy_o(tx36_dst_rdy), + .dataout(tx_data), .src_rdy_o(tx_src_rdy), .dst_rdy_i(tx_dst_rdy)); + + // //////////////////////////////////////////// + // RX Data Path + + wire [17:0] rx18_data, rx18b_data; + wire rx18_src_rdy, rx18_dst_rdy, rx18b_src_rdy, rx18b_dst_rdy; + wire [15:0] rx_fifo_space; + wire [35:0] rx36_data, rx_data; + wire rx36_src_rdy, rx36_dst_rdy, rx_src_rdy, rx_dst_rdy; + wire dummy; + + fifo_cascade #(.WIDTH(36), .SIZE(RXFIFOSIZE)) rx_fifo36 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .datain(rx_data), .src_rdy_i(rx_src_rdy), .dst_rdy_o(rx_dst_rdy), + .dataout(rx36_data), .src_rdy_o(rx36_src_rdy), .dst_rdy_i(rx36_dst_rdy)); + + fifo36_to_fifo19 #(.LE(1)) f36_to_f19 // Little endian because ARM is LE + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .f36_datain(rx36_data), .f36_src_rdy_i(rx36_src_rdy), .f36_dst_rdy_o(rx36_dst_rdy), + .f19_dataout({dummy,rx18_data}), .f19_src_rdy_o(rx18_src_rdy), .f19_dst_rdy_i(rx18_dst_rdy) ); + + fifo_cascade #(.WIDTH(18), .SIZE(12)) rx_fifo + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .datain(rx18_data), .src_rdy_i(rx18_src_rdy), .dst_rdy_o(rx18_dst_rdy), .space(rx_fifo_space), + .dataout(rx18b_data), .src_rdy_o(rx18b_src_rdy), .dst_rdy_i(rx18b_dst_rdy), .occupied()); + + fifo_to_gpmc_async fifo_to_gpmc_async + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .data_i(rx18b_data), .src_rdy_i(rx18b_src_rdy), .dst_rdy_o(rx18b_dst_rdy), + .EM_D(EM_D_fifo), .EM_NCS(EM_NCS4), .EM_NOE(EM_NOE), + .frame_len(rx_frame_len) ); + + wire [31:0] pkt_count; + + fifo_watcher fifo_watcher + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .src_rdy1(rx18_src_rdy), .dst_rdy1(rx18_dst_rdy), .sof1(rx18_data[16]), .eof1(rx18_data[17]), + .src_rdy2(rx18b_src_rdy), .dst_rdy2(rx18b_dst_rdy), .sof2(rx18b_data[16]), .eof2(rx18b_data[17]), + .have_packet(rx_have_data), .length(rx_frame_len), .bus_error(bus_error_rx), + .debug(pkt_count)); + + // //////////////////////////////////////////// + // Control path on CS6 + + gpmc_wb gpmc_wb + (.EM_CLK(EM_CLK), .EM_D_in(EM_D), .EM_D_out(EM_D_wb), .EM_A(EM_A), .EM_NBE(EM_NBE), + .EM_NCS(EM_NCS6), .EM_NWE(EM_NWE), .EM_NOE(EM_NOE), + .wb_clk(wb_clk), .wb_rst(wb_rst), + .wb_adr_o(wb_adr_o), .wb_dat_mosi(wb_dat_mosi), .wb_dat_miso(wb_dat_miso), + .wb_sel_o(wb_sel_o), .wb_cyc_o(wb_cyc_o), .wb_stb_o(wb_stb_o), .wb_we_o(wb_we_o), + .wb_ack_i(wb_ack_i) ); + +// assign debug = pkt_count; + + // //////////////////////////////////////////// + // Test support, traffic generator, loopback, etc. + + // RX side muxes test data into the same stream + wire [35:0] timedrx_data, loopbackrx_data, testrx_data; + wire [35:0] timedtx_data, loopbacktx_data, testtx_data; + wire timedrx_src_rdy, timedrx_dst_rdy, loopbackrx_src_rdy, loopbackrx_dst_rdy, + testrx_src_rdy, testrx_dst_rdy; + wire timedtx_src_rdy, timedtx_dst_rdy, loopbacktx_src_rdy, loopbacktx_dst_rdy, + testtx_src_rdy, testtx_dst_rdy; + wire timedrx_src_rdy_int, timedrx_dst_rdy_int, timedtx_src_rdy_int, timedtx_dst_rdy_int; + + wire [31:0] total, crc_err, seq_err, len_err; + wire sel_testtx = test_ctrl[0]; + wire sel_loopbacktx = test_ctrl[1]; + wire pkt_src_enable = test_ctrl[2]; + wire pkt_sink_enable = test_ctrl[3]; + + fifo36_mux rx_test_mux_lvl_1 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .data0_i(timedrx_data), .src0_rdy_i(timedrx_src_rdy), .dst0_rdy_o(timedrx_dst_rdy), + .data1_i(loopbackrx_data), .src1_rdy_i(loopbackrx_src_rdy), .dst1_rdy_o(loopbackrx_dst_rdy), + .data_o(testrx_data), .src_rdy_o(testrx_src_rdy), .dst_rdy_i(testrx_dst_rdy)); + + fifo36_mux rx_test_mux_lvl_2 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .data0_i(testrx_data), .src0_rdy_i(testrx_src_rdy), .dst0_rdy_o(testrx_dst_rdy), + .data1_i(rx_data_i), .src1_rdy_i(rx_src_rdy_i), .dst1_rdy_o(rx_dst_rdy_o), + .data_o(rx_data), .src_rdy_o(rx_src_rdy), .dst_rdy_i(rx_dst_rdy)); + + fifo_short #(.WIDTH(36)) loopback_fifo + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx | clear_rx), + .datain(loopbacktx_data), .src_rdy_i(loopbacktx_src_rdy), .dst_rdy_o(loopbacktx_dst_rdy), + .dataout(loopbackrx_data), .src_rdy_o(loopbackrx_src_rdy), .dst_rdy_i(loopbackrx_dst_rdy)); + + // Crossbar used as a demux for switching TX stream to main DSP or to test logic + crossbar36 tx_crossbar_lvl_1 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .cross(sel_testtx), + .data0_i(tx_data), .src0_rdy_i(tx_src_rdy), .dst0_rdy_o(tx_dst_rdy), + .data1_i(tx_data), .src1_rdy_i(1'b0), .dst1_rdy_o(), // No 2nd input + .data0_o(tx_data_o), .src0_rdy_o(tx_src_rdy_o), .dst0_rdy_i(tx_dst_rdy_i), + .data1_o(testtx_data), .src1_rdy_o(testtx_src_rdy), .dst1_rdy_i(testtx_dst_rdy) ); + + crossbar36 tx_crossbar_lvl_2 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .cross(sel_loopbacktx), + .data0_i(testtx_data), .src0_rdy_i(testtx_src_rdy), .dst0_rdy_o(testtx_dst_rdy), + .data1_i(testtx_data), .src1_rdy_i(1'b0), .dst1_rdy_o(), // No 2nd input + .data0_o(timedtx_data), .src0_rdy_o(timedtx_src_rdy), .dst0_rdy_i(timedtx_dst_rdy), + .data1_o(loopbacktx_data), .src1_rdy_o(loopbacktx_src_rdy), .dst1_rdy_i(loopbacktx_dst_rdy) ); + + // Fixed rate TX traffic consumer + fifo_pacer tx_pacer + (.clk(fifo_clk), .reset(fifo_rst), .rate(test_rate), .enable(pkt_sink_enable), + .src1_rdy_i(timedtx_src_rdy), .dst1_rdy_o(timedtx_dst_rdy), + .src2_rdy_o(timedtx_src_rdy_int), .dst2_rdy_i(timedtx_dst_rdy_int), + .underrun(tx_underrun), .overrun()); + + packet_verifier32 pktver32 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_tx), + .data_i(timedtx_data), .src_rdy_i(timedtx_src_rdy_int), .dst_rdy_o(timedtx_dst_rdy_int), + .total(total), .crc_err(crc_err), .seq_err(seq_err), .len_err(len_err)); + + // Fixed rate RX traffic generator + packet_generator32 pktgen32 + (.clk(fifo_clk), .reset(fifo_rst), .clear(clear_rx), + .header({len_err,seq_err,crc_err,total}), + .data_o(timedrx_data), .src_rdy_o(timedrx_src_rdy_int), .dst_rdy_i(timedrx_dst_rdy_int)); + + fifo_pacer rx_pacer + (.clk(fifo_clk), .reset(fifo_rst), .rate(test_rate), .enable(pkt_src_enable), + .src1_rdy_i(timedrx_src_rdy_int), .dst1_rdy_o(timedrx_dst_rdy_int), + .src2_rdy_o(timedrx_src_rdy), .dst2_rdy_i(timedrx_dst_rdy), + .underrun(), .overrun(rx_overrun)); + + // FIXME -- hook up crossbar controls + // // FIXME -- collect error stats + // FIXME -- set rates and enables on pacers + // FIXME -- make sure packet completes before we shutoff + // FIXME -- handle overrun and underrun + +wire [0:17] dummy18; + +assign debug = {8'd0, + test_rate, + pkt_src_enable, pkt_sink_enable, timedrx_src_rdy_int, timedrx_dst_rdy_int, + timedrx_src_rdy, timedrx_dst_rdy, + testrx_src_rdy, testrx_dst_rdy, + rx_src_rdy, rx_dst_rdy, + rx36_src_rdy, rx36_dst_rdy, + rx18_src_rdy, rx18_dst_rdy, + rx18b_src_rdy, rx18b_dst_rdy}; + +endmodule // gpmc_async |