1 files changed, 139 insertions, 0 deletions
diff --git a/fpga/usrp2/extramfifo/nobl_if.v b/fpga/usrp2/extramfifo/nobl_if.v
new file mode 100644
index 000000000..391a841e8
--- /dev/null
+++ b/fpga/usrp2/extramfifo/nobl_if.v
@@ -0,0 +1,139 @@
+// Tested against an IDT 71v65603s150 in simulation and a Cypress 7C1356C in the real world.
+
+module nobl_if
+  #(parameter WIDTH=18,DEPTH=19)  
+    (
+     input clk,
+     input rst,
+     input [WIDTH-1:0] RAM_D_pi,
+     output [WIDTH-1:0] RAM_D_po,
+     output reg RAM_D_poe,
+     output [DEPTH-1:0] RAM_A,
+     output reg RAM_WEn,
+     output RAM_CENn,
+     output RAM_LDn,
+     output RAM_OEn,
+     output reg RAM_CE1n,
+     input [DEPTH-1:0] address,
+     input [WIDTH-1:0] data_out,
+     output reg [WIDTH-1:0] data_in,
+     output reg data_in_valid,
+     input write,
+     input enable
+     );
+   
+
+   reg 	   enable_pipe1;
+   reg [DEPTH-1:0] address_pipe1;
+   reg 		   write_pipe1;
+   reg [WIDTH-1:0] data_out_pipe1;
+   
+   reg 		   enable_pipe2;
+   reg 		   write_pipe2;
+   reg [WIDTH-1:0] data_out_pipe2;
+
+   reg 		   enable_pipe3;
+   reg 		   write_pipe3;
+   reg [WIDTH-1:0] data_out_pipe3;
+
+   assign 	   RAM_LDn = 0;
+   // ZBT/NoBL RAM actually manages its own output enables very well.
+   assign 	   RAM_OEn = 0;
+   
+   //
+   // Pipeline stage 1
+   //
+   always @(posedge clk)
+     if (rst)
+       begin
+	  enable_pipe1 <= 0;
+	  address_pipe1 <= 0;
+	  write_pipe1 <= 0;
+	  data_out_pipe1  <= 0;
+       end
+     else
+       begin
+	  enable_pipe1 <= enable;
+	  RAM_CE1n <= ~enable;  // Creates IOB flob
+	  
+	  
+	  if (enable)
+	    begin
+	       address_pipe1 <= address;
+	       write_pipe1 <= write;
+	       RAM_WEn <= ~write;  // Creates IOB flob
+	       
+	       
+	       if (write)
+		 data_out_pipe1 <= data_out;
+	    end
+       end // always @ (posedge clk)
+
+   // Pipeline 1 drives address, write_enable, chip_select on NoBL SRAM
+   assign RAM_A = address_pipe1;
+   assign RAM_CENn = 1'b0;
+ //  assign RAM_WEn = ~write_pipe1;
+//   assign RAM_CE1n = ~enable_pipe1;
+
+   //
+   // Pipeline stage2
+   //
+   always @(posedge clk)
+     if (rst)
+       begin
+	  enable_pipe2 <= 0;
+	  data_out_pipe2 <= 0;
+	  write_pipe2 <= 0;   
+       end
+     else
+       begin
+	  data_out_pipe2 <= data_out_pipe1;
+	  write_pipe2 <= write_pipe1;
+	  enable_pipe2 <= enable_pipe1;
+       end
+   
+   //
+   // Pipeline stage3
+   //
+   always @(posedge clk)
+     if (rst)
+       begin
+	  enable_pipe3 <= 0;
+	  data_out_pipe3 <= 0;
+	  write_pipe3 <= 0;
+	  RAM_D_poe <= 0;	  
+       end
+     else
+       begin
+	  data_out_pipe3 <= data_out_pipe2;
+	  write_pipe3 <= write_pipe2;
+	  enable_pipe3 <= enable_pipe2;
+	  RAM_D_poe <= ~(write_pipe2 & enable_pipe2); // Active low driver enable in Xilinx.	
+       end
+
+   // Pipeline 3 drives write data on NoBL SRAM
+   assign RAM_D_po = data_out_pipe3;
+   
+   
+   //
+   // Pipeline stage4
+   //
+   always @(posedge clk)
+     if (rst)
+       begin
+	  data_in_valid <= 0;
+	  data_in <= 0;
+       end
+     else
+       begin
+	  data_in <= RAM_D_pi;
+	  if (enable_pipe3 & ~write_pipe3)
+	    begin
+	       // Read data now available to be registered.
+	       data_in_valid <= 1'b1;
+	    end
+	  else
+	    data_in_valid <= 1'b0;
+       end // always @ (posedge clk)
+     
+endmodule // nobl_if