diff options
Diffstat (limited to 'firmware/microblaze')
| -rw-r--r-- | firmware/microblaze/apps/txrx.c | 73 |
1 files changed, 24 insertions, 49 deletions
diff --git a/firmware/microblaze/apps/txrx.c b/firmware/microblaze/apps/txrx.c index 262995885..926260bac 100644 --- a/firmware/microblaze/apps/txrx.c +++ b/firmware/microblaze/apps/txrx.c @@ -291,53 +291,6 @@ void handle_udp_ctrl_packet( break; /******************************************************************* - * GPIO - ******************************************************************/ - case USRP2_CTRL_ID_USE_THESE_GPIO_DDR_SETTINGS_BRO: - if (!DEBUG_MODE) hal_gpio_set_ddr( - OTW_GPIO_BANK_TO_NUM(ctrl_data_in->data.gpio_config.bank), - ctrl_data_in->data.gpio_config.value, - ctrl_data_in->data.gpio_config.mask - ); - ctrl_data_out.id = USRP2_CTRL_ID_GOT_THE_GPIO_DDR_SETTINGS_DUDE; - break; - - case USRP2_CTRL_ID_SET_YOUR_GPIO_PIN_OUTS_BRO: - if (!DEBUG_MODE) hal_gpio_write( - OTW_GPIO_BANK_TO_NUM(ctrl_data_in->data.gpio_config.bank), - ctrl_data_in->data.gpio_config.value, - ctrl_data_in->data.gpio_config.mask - ); - ctrl_data_out.id = USRP2_CTRL_ID_I_SET_THE_GPIO_PIN_OUTS_DUDE; - break; - - case USRP2_CTRL_ID_GIVE_ME_YOUR_GPIO_PIN_VALS_BRO: - ctrl_data_out.data.gpio_config.value = hal_gpio_read( - OTW_GPIO_BANK_TO_NUM(ctrl_data_in->data.gpio_config.bank) - ); - ctrl_data_out.id = USRP2_CTRL_ID_HERE_IS_YOUR_GPIO_PIN_VALS_DUDE; - break; - - case USRP2_CTRL_ID_USE_THESE_ATR_SETTINGS_BRO:{ - //setup the atr registers for this bank - int bank = OTW_GPIO_BANK_TO_NUM(ctrl_data_in->data.atr_config.bank); - if (!DEBUG_MODE) set_atr_regs( - bank, - ctrl_data_in->data.atr_config.rx_value, - ctrl_data_in->data.atr_config.tx_value - ); - - //setup the sels based on the atr config mask - int mask = ctrl_data_in->data.atr_config.mask; - for (int i = 0; i < 16; i++){ - // set to either GPIO_SEL_SW or GPIO_SEL_ATR - if (!DEBUG_MODE) hal_gpio_set_sel(bank, i, (mask & (1 << i)) ? 'a' : 's'); - } - ctrl_data_out.id = USRP2_CTRL_ID_GOT_THE_ATR_SETTINGS_DUDE; - } - break; - - /******************************************************************* * SPI ******************************************************************/ case USRP2_CTRL_ID_TRANSACT_ME_SOME_SPI_BRO:{ @@ -354,8 +307,8 @@ void handle_udp_ctrl_packet( (ctrl_data_in->data.spi_args.readback == 0)? SPI_TXONLY : SPI_TXRX, (ctrl_data_in->data.spi_args.dev == USRP2_DIR_RX)? SPI_SS_RX_DB : SPI_SS_TX_DB, data, num_bytes*8, //length in bits - (ctrl_data_in->data.spi_args.push == USRP2_CLK_EDGE_RISE)? SPIF_PUSH_RISE : SPIF_PUSH_FALL | - (ctrl_data_in->data.spi_args.latch == USRP2_CLK_EDGE_RISE)? SPIF_LATCH_RISE : SPIF_LATCH_FALL + (ctrl_data_in->data.spi_args.edge == USRP2_CLK_EDGE_RISE)? SPIF_PUSH_RISE : SPIF_PUSH_FALL | + (ctrl_data_in->data.spi_args.edge == USRP2_CLK_EDGE_RISE)? SPIF_LATCH_RISE : SPIF_LATCH_FALL ); //load the result into the array of bytes @@ -571,6 +524,24 @@ void handle_udp_ctrl_packet( ctrl_data_out.id = USRP2_CTRL_ID_UPDATED_THE_MUX_SETTINGS_DUDE; break; + /******************************************************************* + * Peek and Poke Register + ******************************************************************/ + case USRP2_CTRL_ID_POKE_THIS_REGISTER_FOR_ME_BRO: + if (ctrl_data_in->data.poke_args.addr < 0xC000){ + printf("error! tried to poke into 0x%x\n", ctrl_data_in->data.poke_args.addr); + } + else{ + *((uint32_t *) ctrl_data_in->data.poke_args.addr) = ctrl_data_in->data.poke_args.data; + } + ctrl_data_out.id = USRP2_CTRL_ID_OMG_POKED_REGISTER_SO_BAD_DUDE; + break; + + case USRP2_CTRL_ID_PEEK_AT_THIS_REGISTER_FOR_ME_BRO: + ctrl_data_in->data.poke_args.data = *((uint32_t *) ctrl_data_in->data.poke_args.addr); + ctrl_data_out.id = USRP2_CTRL_ID_WOAH_I_DEFINITELY_PEEKED_IT_DUDE; + break; + default: ctrl_data_out.id = USRP2_CTRL_ID_HUH_WHAT; @@ -759,6 +730,10 @@ main(void) hal_gpio_set_ddr(GPIO_TX_BANK, 0x8000, 0x8000); #endif +//set them all to the atr settings by default +hal_gpio_set_sels(GPIO_TX_BANK, "aaaaaaaaaaaaaaaa"); +hal_gpio_set_sels(GPIO_RX_BANK, "aaaaaaaaaaaaaaaa"); + output_regs->debug_mux_ctrl = 1; #if DEBUG_MODE hal_gpio_set_sels(GPIO_TX_BANK, "0000000000000000"); |